StarTech.com SV831DVIU Bedienungsanleitung

Rack Mount DVI USB

KVM Switch

8-Port 1U Rack Mount DVI USB

KVM Switch

SV831DVIU

Instruction Manual

Manual Revision:11/23/2010

For the most up-to-date information, please visit www.startech.com

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company

in question. Regardless of any direct acknowledgement elsewhere in the body of

this document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Table of Contents

Introduction.................................................................1

Packaging Contents.............................................................................. 1

System Requirements .......................................................................... 1

Installation...................................................................2

Hardware Installation............................................................................ 2

Operation.....................................................................4

Front Panel ........................................................................................... 4

Hot-key commands............................................................................... 5

Speciﬁcations..............................................................7

Technical Support.......................................................8

Warranty Information ..................................................8

Introduction

The SV831DVIU 8 Port 1U Rack Mount DVI USB KVM Switch allows you to

control up to 8 USB connected computers with DVI or HDMI display output

from a single keyboard, mouse and monitor.

The KVM switch offers maximum control, allowing you to switch computers

using hot-key commands or front panel push-buttons. Supporting resolutions

up to 1920x1200 via DVI or HDMI connection (using DVI to HDMI adapter),

the KVM provides the high resolutions recommended for newer displays

allowing you to take full advantage of your screen real-estate.

A perfect addition to any server room operation, this rugged 8 port switch

can be rack-mounted into 1U of cabinet space.

Packaging Contents

• 1 x 1U Rack Mount KVM Switch

• 3 x Power Cord (NA/UK/EU)

• 1 x Set of rack mount brackets

• 1 x Instruction Manual

System Requirements

• DVI/HDMI enabled display device (i.e. monitor, projector, HDTV, etc)

• USB 104-key wired keyboard

• USB 3-button wired mouse

• Computer systems with an available DVI/HDMI and USB port

Front View

Rear View

Installation

Hardware Installation

WARNING: Prior to installation, please ensure that all of the computers and

the KVM switch are powered down.

Console Connection

The KVM switch is designed to use USB console connections only. A USB

compatible keyboard and mouse and DVI/HDMI* monitor must be used for

the local console.

NOTE: DVI to HDMI adapters sold separately.

Plug a monitor into the Console’s DVI connector; plug a USB keyboard and a

USB mouse into the dedicated USB keyboard and mouse ports on the KVM

switch. Ensure the keyboard/mouse are connected to the proper connectors.

Connecting Computer to the KVM Switch

To connect a computer to the KVM switch, use the appropriate DVI/USB

KVM cable (or separate cables) to connect from one of the PC ports located

on the rear panel of the KVM switch to the USB and DVI video ports on the

computer.

1.Use a male-to-male DVI video cable to connect the DVI connector on the

computer’s video card, to one of the KVM’s PC ports (i.e. PC1).

2.Use a USB type A-B Cable to connect the KVM’s USB port (type B,

square connector) for the PC port used in Step 1, and the USB port on the

computer (type A, ﬂat connector).

3.Repeat for Steps 1 and 2 for each PC port on the KVM switch, or each

computer you wish to use on the KVM.

4.Connect the power cord from the KVM to an AC power outlet.

5.Turn the monitor on ﬁrst, followed by the KVM switch via the power switch

on the rear panel.

6.Power up the ﬁrst computer/device and wait for it to fully boot and test

keyboard/mouse functionality.

7.Once operation has been successfully conﬁrmed, switch to the next port

and power up that computer/device and conﬁrm.

Operation

Front Panel

Port Selection/Link LED

The LED turns green when the connected computer is powered-on. The

corresponding LED will also illuminate red when that PC port is currently

selected.

Port Selection Button

Each push button on the front panel corresponds with a PC port. Pressing

the button will immediately select that port.

K/M Reset

K/M Reset resolves the majority of problems developed by keyboard

and/or mouse device replacement or conﬁguration changes. Press

down buttons 1 and 2 simultaneously for 2 seconds to reconﬁgure the

whole system without having to turn off the KVM switch or any attached

computers.

Auto Scan

The KVM automatically scans through the powered-on computers in

sequence on a ﬁxed time interval (see Scan Time below).

To activate Auto Scan, press down front panel push buttons “3” and “4”

simultaneously. The port LED ﬂashes during Auto Scan. Auto Scan is

effective for powered-on computers only. To exit the Auto Scan mode, just

tap any one of the push buttons.

NOTE: When Auto Scan detects any keyboard activity, it suspends the

scanning until the activity stops; it then resumes with the next computer in

sequence. The length of the Auto Scan interval (Scan Rate) is adjustable,

see below.

Hot-key commands

A Hot-key command is a short keyboard sequence for selecting a computer,

activating computer scan, etc. A hot-key sequence starts with two left

<CTRL> keystrokes (successively within 0.2 seconds) followed by one or

two more keystrokes. A high-pitch beep will be generated for each correct

hot-key command; otherwise, one low-pitch beep is generated for errors and

the bad key sequence will not be forwarded to the selected computer.

NOTE: Left <CTRL>: refers to the Control key on the left side of the

keyboard.

1~8: refers to the number keys ‘1’~’8’ in the upper row of the keyboard. Do

not use the keypad at the right of the keyboard.

To select a computer by hot-key command, you must know its port number,

which is determined by the KVM switch connections.

EXAMPLES:

Left <CTRL> , Left <CTRL>, 7 : Selects a computer connected to PC port

7 on the KVM switch.

Auto Scan

In this mode, the KVM Switch automatically switches from one power-on

computer to the next, sequentially, at a ﬁxed interval.

Left <CTRL>, Left <CTRL>, F1

When Auto Scan detects any keyboard or mouse activity, it suspends the

scanning until the activity stops. It then resumes with the next computer in

sequence. The length of the Auto Scan interval (Scan Time) is adjustable.

To abort Auto Scan mode, press the left <CTRL> key twice.

Manual Scan

Enables you to manually switch back and forth between the powered

computers:

Left <CTRL>, left <CTRL>, F2

Press the <UP> arrow key to select the previous computer and the

<DOWN> arrow key to select the next computer. Press any other key to

abort Manual Scan mode.

Scan Time

To adjust Scan Time, which sets the duration before switching to the next

computer in Auto Scan:

Left <CTRL>, Left <CTRL>, F3

The switch will beep one to four times indicating the scan interval of 3, 8,

15 and 30 seconds respectively.

Inhaltsverzeichnis

Andere StarTech.com Schalten Handbücher

StarTech.com

StarTech.com SV231DDVDUA Bedienungsanleitung

StarTech.com

StarTech.com 8STST7300USBME Bedienungsanleitung

StarTech.com

StarTech.com ICUSB23208FD Bedienungsanleitung

StarTech.com

StarTech.com VS721MULTI Bedienungsanleitung

StarTech.com

StarTech.com 5port Bedienungsanleitung

StarTech.com

StarTech.com SDOCK2U33HFW Bedienungsanleitung

StarTech.com

StarTech.com STARVIEW SV831SUN Bedienungsanleitung

StarTech.com

StarTech.com WIFI2HDVGAGE Bedienungsanleitung

StarTech.com

StarTech.com StarView SV231USB Bedienungsanleitung

StarTech.com

StarTech.com IESC1G50UP Bedienungsanleitung

StarTech.com

StarTech.com IES81000POE Bedienungsanleitung

StarTech.com

StarTech.com SV231UADVI Bedienungsanleitung

StarTech.com

StarTech.com ES3116 Bedienungsanleitung

StarTech.com

StarTech.com HB30A7AME Bedienungsanleitung

StarTech.com

StarTech.com ST4200USB Handbuch

StarTech.com

StarTech.com SV231TDVIUA Bedienungsanleitung

StarTech.com

StarTech.com SV441DUSBI Bedienungsanleitung

StarTech.com

StarTech.com 8STICUSB23216FD Bedienungsanleitung

StarTech.com

StarTech.com DS8105 Systemhandbuch

StarTech.com

StarTech.com SV231DDVDUA Bedienungsanleitung

StarTech.com

StarTech.com SV231DPDDUA2 Bedienungsanleitung

StarTech.com

StarTech.com StarView SV221DD Handbuch

StarTech.com

StarTech.com SV231DVIDDU Bedienungsanleitung

StarTech.com

StarTech.com HBS304A24A Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung