Stealth Cam QV20 Bedienungsanleitung
QV20 Instruction
Manual
R0
Page 2
Notice
To ensure the product is being utilized to its full potential, we recommend checking our
website for new product updates. If your camera is having an issue, please check the
website to determine you are using the latest firmware or software version.
Contact Us
TECHNICAL SUPPORT
EMAIL:
Stealthcam@gsmorg.com
Please allow 48 hours for email
response.
STEALTH CAM LLC
P.O. Box 535189
Grand Prairie, TX 75053-9504
CUSTOMER SERVICE
CONTACT & HOURS
Toll Free: 877‐269‐8490
CALL CENTER HOURS
Mon – Fri / 8 AM – 5 PM (CST)
WEBSITE
www.stealthcam.com
QV20
Page 4
About Your Camera
Device Features
Energy Efficient Design
Completely re-energized to optimize energy efficiency.
Burst Rapid-Fire Mode
Rapid-fire Burst Mode, 1-9 exposures per triggering.
Quick Set Options
Set up in seconds with pre-programmed options.
Expand Storage Space
Expand your storage space with an SD memory card up to 32 GB.
Page 5
Camera Overview
Page 6
Quick Set-up Guide
Insert Batteries and SD Card
Install 8 AA batteries and a class 10 SD card into camera.
Mount Camera
Mount the camera at the desired location using the strap mount, Python Lock
cable, Articulating Ball Joint Mount, or other desired mounting mechanism.
Position the camera so that it does not face East or West directly as the rising
and setting of the sun can cause false positive triggers.
Activate Camera
Set camera to "On" position and place in desired
vantage point to start capturing photos of game.
Page 7
Camera Care
Operating Conditions
This camera is designed to function in 14°F – 104°F (10°C - 40°C). 20%-85%
relative humidity, non-condensing.
Product Care
❖When not in use, store camera in a cool, dust-free, environment.
❖Handle camera with care
❖Camera is weather resistant only. Do no fully submerge camera in water or
other liquid. Doing so will void camera warranty.
❖Only use same type of batteries to power camera. Do not mix old and new
batteries.
❖Do not touch camera lens directly. Clean only with soft lens cloth.
❖Use damp cloth to clean. DO NOT submerge camera.
❖Remove batteries when camera is not in use for an extended time.
❖Do not open camera housing to access internal parts. Doing so could damage
camera and void warranty.
Notice
Camera is an active electronic device. Attempting to service internal parts may
expose you to dangerous voltages and other risks.
Page 8
Camera Setup
Battery Installation
To remove batteries from unit, simply open camera, and slide the battery
release switch to the left. Once the battery compartment is open, insert
batteries into camera, being careful to match the orientation marked on your
camera. After batteries are inserted, close the battery compartment and
secure the battery release switch.
SD Card Installation
SD card slot is located on the bottom of the
camera, above the battery compartment. Insert
SD card with the label facing back of camera.
Only minimal resistance should be felt as card is
inserted and a click when the card is fully
inserted.
Page 9
Camera Configuration
Cycle between camera modes by pressing the UP and DOWN arrows. The
camera mode will be displayed on the left side of the LCD Screen. This camera
comes equipped with two Quick Sets (QSET) containing some of our most
popular configurations. QSET 1 and 2 are defined in the table below. For
alternate configurations, press the UP or DOWN arrows until CUSTOM is
displayed on the left of the LCD screen and press ENTER.
Name
Quality
Timeout Delay
Detail
QSET 1
Med
30s
1 Photo
QSET 2
Med
30s
10 sec Video
Continue to next page for more information regarding each setting.
Page 10
OPERATION MODE: The operation mode setting is
accessible immediately after the Time setting. The
screen will be blank with either Video or Photo
displayed on the right side of screen. Press Enter to
change between Photo and Video mode
OPTIONS: Photo | Video
❖DELETE CARD: Selecting “Yes” on this setting
will completely format the SD card inserted into
the camera. Formatting an SD card will
completely erase any data present on the card. It
is recommended to format an SD card before use
inside a Stealth Cam camera.
OPTIONS: Yes | No
Custom Settings
DATE: This setting allows you to enter the date as it
will appear on the info bar of each photo.
TIME: This setting allows you to enter the time as it will
appear on the info bar of each photo.
❖RESET: Selecting “Yes” on this option will reset
every setting back to the default configuration.
Selecting “Yes” will completely wipe your custom
configuration.
OPTIONS: Yes | No
Advanced Options
To navigate to the following advanced options, PRESS and HOLD ENTER button.
Inhaltsverzeichnis
Sprachen:
Andere Stealth Cam Scouting-Kamera Handbücher
Stealth Cam
Stealth Cam ZX36NG Bedienungsanleitung
Stealth Cam
Stealth Cam STC-AD2 Bedienungsanleitung
Stealth Cam
Stealth Cam STC-G45NGMAX Bedienungsanleitung
Stealth Cam
Stealth Cam V30NGKX Bedienungsanleitung
Stealth Cam
Stealth Cam STC-RX36 Bedienungsanleitung
Stealth Cam
Stealth Cam STC-Z8IRTL Bedienungsanleitung
Stealth Cam
Stealth Cam STC-I540IR Bedienungsanleitung
Stealth Cam
Stealth Cam DIGRC-XTRV Bedienungsanleitung
Stealth Cam
Stealth Cam G45NGX Gebrauchs- und Pflegehandbuch
Stealth Cam
Stealth Cam STC-SK724 Bedienungsanleitung
Stealth Cam
Stealth Cam Reactor Bedienungsanleitung
Stealth Cam
Stealth Cam STC-GMAX32V Bedienungsanleitung
Stealth Cam
Stealth Cam RX36NG Kurzanleitung
Stealth Cam
Stealth Cam ZX36NG Bedienungsanleitung
Stealth Cam
Stealth Cam DS4K Bedienungsanleitung
Stealth Cam
Stealth Cam STC-IR1 Bedienungsanleitung
Stealth Cam
Stealth Cam PX Pro Series Bedienungsanleitung
Stealth Cam
Stealth Cam STC-WD3RT Bedienungsanleitung
Stealth Cam
Stealth Cam STC-AD3X Bedienungsanleitung
Stealth Cam
Stealth Cam STC-BT14 Bedienungsanleitung
