Stevens Aero Model CAP 232 Bedienungsanleitung
© 2003 Stevens AeroModel Page 1 5/8/2008
CAP 232
1:12 Scale micro
V2.01
Span 24.2” / Length 22.2” / Area 105 Sq.” / Weight 6-7oz
© 2003 Stevens AeroModel Page 2 5/8/2008
REQUIRED TO COMPLETE KIT
Kit Contents:
¾Computer Drawn Rolled Plan Sheet
¾Illustrated Instruction Manual
¾1 - Clear Canopy
¾1 - Cowl Assembly
¾Bricked Wood and Wire/Tube Stock
Laser Cut Balsa and Hardwood Parts (See Parts Inventory Sheet)
2 - 1/32” x 12” Music Wire.
1 - 12” Length of pull/pull guide tubing.
2 - 3/16” Square x 18” balsa stock
2 - 3/16” Square x 12” balsa stock
¾Hardware Bag (4x6 Bag)
2 - 1/8” x 3” hardwood wing dowel (Wing Hold Down)
1 - 1/8” x 2” hardwood wing dowel.
1 - 1/4” x 3” hardwood dowel (LPS Motor Mount)
2 - 0.070” x 3” length carbon rod (Landing Gear Struts)
1 - 1/16” x 3” length heat shrink tubing.
1 - 1/16” x 4” aluminum tube.
2 - 1”x3/4” CA Hinges
1 - Package #16 rubber bands.
Suggested Finishing Items:
¾DuBro RC 1” Mini lite wheels (DUB100MW).
¾DuBro RC Micro Pull/Pull Assembly (DUB846).
¾1 Roll Stevens AeroModel AeroLITE film
Suggested Radio Gear:
Note that the Micro Cap 232 was originally designed for brushed power systems. The design lends itself
very well to brushless power. When running a brushless system shoot for a motor that turns a 6-7” propeller
with authority while producing about 45-60 Watts. This should be ample power for the micro Cap 232.
Small hand wound CD Rom motors and similar outrunners readily attach to the motor stick and are capable
of the required power output. New light weight servos can also be used in place of the GWS Pico servos -
Cirrus CS101’s work great and only require minor fit modifications.
¾3 - GWS Pico Servos (GWSPIC/STD/J)
¾1 - Sub-micro Receiver 6g or less (Berg MS4L)
¾1 - 2A ESC (GWESC050A)
¾1 - LPS-RLC-C 4.8v (6.0:1)
¾1 - Motor Heat Sink (GW/EHS-50)
¾1 - 7x6 Slow-Fly Prop (GW/EP7060)
¾1 - 7.4V 350mAh or smaller LiPo battery (ThunderPower RC Pro-Lite 350mAh)
Things you may need:
¾Thin CA (super glue)
¾CA Glue Tips
¾Five Minute Epoxy
¾Plastic Model Cement
¾Clear Plastic Wrap (for protecting plans)
¾Razor Blade(s)
¾Fine Grit Sand Paper
¾Flat Rat Tail File or Emery Board
¾Clear Tape
¾Balsa Wood Filler
¾Sewing Thread
© 2003 Stevens AeroModel Page 4 5/8/2008
GENERAL ASSEMBLY INSTRUCTIONS:
Thank you, for purchasing this Stevens AeroModel 1:12 Scale Cap 232 (MICRO).
Please keep in mind that while small and cute like a “park flyer” this is a sport plane and behaves as such.
Therefore we recommend this kit to the advanced pilot. The tiny airframe, wheels, and building materials
exclude this model from flying from anything but and improved surface (read: sealed asphalt, concrete,
etc..). A good rule of thumb –if you cannot readily taxi and take off from the surface – do not attempt to land
there!
We hope you enjoy this model as much as we have.
Sincerely,
Bill Stevens
Stevens AeroModel
1528 S. Nevada Ave.
Colorado Springs, CO 80906
General Assembly Tips
READ THE INSTRUCTIONS and the plan sheet prior to starting any work!
Tape plans to work table. Cover with wax paper or plastic wrap.
Join all joints with Thin CA unless otherwise specified.
DO NOT REMOVE THE PARTS FROM THE BALSA SHEETS UNTIL REQUIRED!
DO NOT FORCE THE FIT – when in doubt double check your parts and remove material should
not be required. If you feel that you have a poor connection check first to see that the part is not
upside down. Next, referenced each piece against the plan sheet.
This is very important so I’ll say it again – Prior to gluing, test fit and match parts over the plan
sheet to ensure you have the correct pieces and orientation.
Making solid glue joints: Hold parts together on top of plan sheet using moderate pressure to fit
parts - wick thin CA into joint. (There is no need to pin parts to work table as all pieces interlock
and self - jig.)
© 2003 Stevens AeroModel Page 5 5/8/2008
Tail Feathers
1. Build the Rudder, Vertical Stabilizer, Elevator, and Horizontal Stabilizer. Parts are grouped
according to tail section component on the 3/32” balsa sheet. Work with each component
separately. Assemble over plan sheet, removing only those parts necessary to complete each
individual component. Though the parts fall together and self jig, pay particular attention to making
solid glue joints. (note: at the time of printing your plan sheet may reflect the old-style tail feathers
use the included update sheet to replace the parts overlay for the tail feathers as illustrated on the
plan sheet)
F
Elevator
Horizontal
Stab.
D
A
D
A
EE
BB
C
F
C
FF
CC
E
E
BB
DDVertical
Stab.
F
F
I
I
E
E
G
G
H
H
2. Elevator Joining Tube. Locate the provided 1/16” aluminum tube - rough the surface with fine grit
sand paper to remove dirt, oil, and debris, from the tube. Bond elevator halves over plan sheet
using thin CA tack the joining tube to each elevator halve and allow to dry. Once dry use a small
amount of 5-minute epoxy to create a fillet between the wood and the metal tube.
3. Sand all surfaces with fine grit sandpaper and bevel / taper hinged surfaces in preparation for your
preferred hinging method.
Fuselage
Fuselage components are exceptionally brittle until the entire assembly is complete. Handle parts
accordingly and do not force the fit!
1. Join over plan sheet F16A and F16B to produce 2 F16 fuselage side sheets.
© 2003 Stevens AeroModel Page 6 5/8/2008
2. Assemble formers F4, F5, and F6. Join over plan sheet F4A, F4B, F4C, F4D, F5A, F5B, F5C,
F5D, F6A, F6B, F6C.
3. Assemble fuselage sides over plan sheet. Parts are grouped on the 3/32” balsa sheet. Make 2
sides.
4. Locate Firewall parts F1 and F2 – if using the recommended LPS drive insert the 10mm balsa
square with the ¼” hole into both F1 and F2 (Hole should be positioned such that it is at the lower
part of the square when joined to F1/F2. Join fuselage sides to F1, F2 and F1A. Test fit parts
before gluing.
F1 F2
F1A
LPS Adapterx2
© 2003 Stevens AeroModel Page 7 5/8/2008
5. Install F3A, F3B and servo rails SR1-SR2. Site fuselage construction over plan sheet top view to
ensure straight and true assembly. Join each of these to the fuselage sides in their respective
positions. Note the servo rails are composed of a top piece SR1 and bottom 3/32” doublers SR2.
6. Glue F14 3/32” stringers to top of F1, F2, and F3A.
1. Pinch fuselage sides together at tail position, using a flat rat tail file or emery board bevel the
notches and alignment tabs in the fuselage to better accommodate formers F4, F5, and F6.
© 2003 Stevens AeroModel Page 8 5/8/2008
2. Test fit former F4 and F15 to fuselage. Align over top view on plan sheet and secure with thin CA.
Hint: Sand a slight bevel on sides of former F4 to aid fit. Again, do not force fit!
3. Proceed to install former F5 and F6 inserting F13 stringer along the bottom of the formers to jig the
assembly. Initially test fit F5 and F6 then glue F5 and F6 to fuselage sides - then glue (if the fit is
too snug bevel the notches with a rat-tail file or emery board). Only glue F13 where it makes
contact with F4, F5, and F6 – Do not glue F13 to fuselage sides at this time!
4. Test fit former F7. Capture aft section of F13 between fuselage sides, do not glue at this time.
© 2003 Stevens AeroModel Page 9 5/8/2008
5. Place some sort of weight over servo rails. Using a builders square hold tail section 90 degrees to
building table and glue F7 and F13.
6. Add tail gear block F11 to aft section of F13 inside fuselage.
7. Laminate F10 in position over aft section of fuselage. Important - Key F10 to top of F7.
© 2003 Stevens AeroModel Page 10 5/8/2008
8. Laminate F9 to F10, key to F7. DO NOT align with holes provided in F10 but key to F7.
9. Test fit F12 to F8. Lay F8 on building table, press F12 into F8 and glue.
10. Test F12/F8 assembly to formers F4, F5, and F6 (do not glue until specified). Align outer edge of
F8 with outer edge of F9 and tack glue just the aft end of both parts.
© 2003 Stevens AeroModel Page 11 5/8/2008
11. Test fit horizontal stabilizer in the slot created between F10 and F8. Snug F6 against F12/F8
assembly – remove horizontal stab and glue. Finish gluing parts F8 and F9
12. Glue F12/F8 assembly to F4 and F5.
13. Laminate finishing blocks to top of F8.
14. Sheet fuselage sides with F16.
15. Sheet fuselage top/front with F17. Test fit – then secure one end with thin CA. Next, gradually tack
down the sheets to the formers with thick CA.
Andere Handbücher für CAP 232
1
Andere Stevens Aero Model Spielzeug Handbücher
Stevens Aero Model
Stevens Aero Model SkyBuggy 100 Handbuch
Stevens Aero Model
Stevens Aero Model RingRat 100 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model GYM-E Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model Hummingbird (100) Betriebsanleitung
Stevens Aero Model
Stevens Aero Model SHAFT S400 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model QuickOats100 Handbuch
Stevens Aero Model
Stevens Aero Model PuddleBug 2.4 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model SQuiRT Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model Build It! Pietenpol Sky Scout 1928 Handbuch
Stevens Aero Model
Stevens Aero Model SQuiRT Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model Farman Carte Postale Post Card Betriebsanleitung
Stevens Aero Model
Stevens Aero Model QuickOats 100 Betriebsanleitung
Stevens Aero Model
Stevens Aero Model Swift 100 Handbuch
Stevens Aero Model
Stevens Aero Model QuickOats 250 Handbuch
Stevens Aero Model
Stevens Aero Model 1928 Pietenpol SkyScout Handbuch
Stevens Aero Model
Stevens Aero Model WaterBoard PondFlyer Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model SHAFT25e Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model LiddleRod 2.4 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model Scimon 20 Handbuch
Stevens Aero Model
Stevens Aero Model G-480 Bedienungsanleitung
