Stevens Aero Model SQuiRT Bedienungsanleitung
1
© 2005 Stevens AeroModel all rights reserved.
SQuiRT
Aileron Wing Kit
V1.02b
Span 38” / Area 260Sq.”
2
© 2005 Stevens AeroModel all rights reserved.
WARRANTY
Stevens AeroModel guarantees this kit to be free from defects in both material and workmanship
at the date of purchase. This warranty does not cover any component parts damaged by use or
modification. In no case shall Stevens AeroModel’s liability exceed the original cost of the
purchased kit. Further, Stevens AeroModel reserves the right to change or modify this warranty
without notice.
In that Stevens AeroModel has no control over the final assembly or material used for final
assembly, no liability shall be assumed nor accepted for any damage resulting from the use by
the user of the final user-assembled product. By the act of using the user–assembled product,
the user accepts all resulting liability.
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer
is advised to return this kit immediately in new and unused condition to the place of purchase.
3
© 2005 Stevens AeroModel all rights reserved.
REQUIRED TO COMPLETE KIT:
Kit Contents:
1. Rolled Computer Drawn Plan Sheet
2. Illustrated Instruction Manual
3. Laser Cut Balsa and Hardwood Parts Sheets (See Cut Parts Inventory Sheet)
4. Included Hardware
5. 2 - 1/8” x 17.5” Hardwood dowels
•1-1/8”x3”hardwooddowels.
• 1 - 6” length of servo guide tube (paper)
•1-#16RubberBands(10).
•2-.045”x5”PushRods.
• 1 - Pair Balsa Aileron Stock.
• 1 - Pair Fiberglass Control Horns.
•1-Du-bro845E-ZConnectors(2/Pkg.)
Recommended Finishing Items:
1. One roll of AeroFILM covering available from www.stevensaero.com
Suggested Electronics:
1. 4 Channel Transmitter.
2. 2 - Hitec HS-55 Servos (use of HS-55 servos will negate the need for two 6” servo extensions)
3. 2 - 6” Servo Extension (Only required if you do not use the suggested HS-55 Servos)
4. 1 - 6” Servo “Y” Harness
Items You May Need:
1. Thin CA (super glue) or White Glue
2. Plan/Table Protector (use the bag that this kit came in to protect your work surface from CA glue spills)
3. Razor Blade(s)
4. Med-Fine Grit Sand Paper and sanding block
5. Clear Tape
6. Balsa Wood Filler
5
© 2005 Stevens AeroModel all rights reserved.
INSTRUCTIONS:
Thank you, for purchasing this Stevens Aeromodel SQuiRT – Aileron Wing Kit. This kit provides the builder and pilot a
refreshing change of pace from heavy “ARF” style plywood box airframe construction and blends stick and tissue design
methods of the past with state of the art CAD technology and precision interlocking laser cut parts; the result is something
you will find truly exceptional to build and fly. This kit is intended for a beginner-novice builder and beginner pilot as a
primary 3-channel trainer.
Best Regards,
Bill Stevens
Stevens AeroModel “Laser Engineered Kits™”
P.O. Box 15347
Colorado Springs, CO 80935
6
© 2005 Stevens AeroModel all rights reserved.
Wing Assembly
Basic assembly method. Friction fit all parts together prior to gluing. Sanding parts prior to assembly is not advised
nor should it be required. Prior to installing tab/notch parts gently pinch the tab of each part to allow it to slip into the
corresponding notch. Do not try and force parts together – instead use a solid work surface to support your work
and gently install parts using a rocking motion. You’ll find, particularly when installing the D-Lock ™ interlocking d-
tube sheeting, that slightly rubbing back and forth over the tab notch joint with your finger tip will help seat your parts.
Please use thin CA glue for the entire assembly. Do not use thin CA glue without a glue tip installed as you’ll be in
for a sticky mess. Use the poly tube that this kit was shipped in to protect your plan sheet or work table from CA
spills (Cut tube down one side and unfold over your plans – CA glue will not stick to this poly tube). We suggest that,
as you assemble this wing, you only tack glue the parts at the tab/notch locations. Once the assembly has been
completed you should thoroughly wick thin CA glue into all joints. Note that one small drop of CA glue will
adequately wick into a surface joint of about 2 inches in length! CA Accelerator (Kicker) is a handy item for setting
your glue joints faster and will become a necessity should you need to repair parts/joints where the bonding surface
is already soaked with old/set CA glue.
Hint: Keep from gluing yourself to the work! – wrap each finger tip with masking tape. This will prevent you from
bonding yourself to the wing during assembly!
Join S1a to S1b to create S1 main spar.
Join part W5 to bottom center of S1 spar. Next, interlock parts W1 to spar S1 on either side of W5 take note of
the part orientation as W1 is etched to correspond with the R1 rib location. Secure assembly with CA glue at
the tab and notch locations. (see plan sheet for more detail)
7
© 2005 Stevens AeroModel all rights reserved.
InstallRibsR2towingassemblyinthe locations indicated on the plan sheet.
Nextlayinthe1/16”plyspardoublerS2betweenribsR2andontheaftsideofsparS1–retaintheplydoubler
by slipping ribs R1 over the spar and doubler. Wick thin CA in between the balsa S1 spar, ply doubler S2, and
ribs R1.
Install Ribs R3 as indicated on the plan sheet. Next, Install Rib R4 at wing tips as indicated on the plan sheet.
8
© 2005 Stevens AeroModel all rights reserved.
Install Rib R2a as indicated on plan sheet.
Install parts TE2 at wing center section trailing edge as indicated on the plan sheet (etched arrows up). Next,
join parts TE1 to either side of TE2 (the arrows etched on the surface of TE1 should face those of TE2).
Finalize center section trailing edge by installing the 1/16” ply doubler TE3 along trailing edge of wing center
section using the recess created by parts TE1 and TE2 to position the part.
9
© 2005 Stevens AeroModel all rights reserved.
Complete the trailing edge by first assembling parts TE4 and TE5. Notice that TE5 is etched with “FRONT” this
surface should face up when you install TE4. Also note that TE4 is keyed to fit in only one direction. Install the
completed assembly to the wing trailing edge spanning ribs R2, R2a, R3, and R4. Again, please note the part
orientation as the etch marks on TE5 should face the front or leading edge of the wing. You’ll see where this
orientation is important as the tip of each trailing edge part is tapered up at an angle to match the wing tips.
Using a new sharp razor blade, cut the provided 6” paper tube into two equal 3” lengths. Gently sand the burr
(from cutting) off each end of these tubes. Next install these between R1 and R2 by gently working the part into
R1 from the bottom side of the wing until it clears R2 and can then be centered between the ribs. Hint: Use a
twisting motion and gentle pressure to work the tube into position. DO NOT GLUE THIS TUBE IN YET
10
© 2005 Stevens AeroModel all rights reserved.
Install ply servo pocket SR1 to wing assembly between ribs R2 and R2a. SR1 is notched to only fit in one
direction. Once satisfied with the fit, glue both parts SR1 and the paper servo guide tube (installed in the
previous step).
Install lower cap strips W9 (bottom of R2) and W9a (bottom of R2a and ribs R3).
Install part SR2 over ply servo pocket SR1.
Andere Handbücher für SQuiRT
1
Inhaltsverzeichnis
Andere Stevens Aero Model Spielzeug Handbücher
Stevens Aero Model
Stevens Aero Model BuzzBomb 400 Handbuch
Stevens Aero Model
Stevens Aero Model Ace 100 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model LiddleRod 2.4 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model Avro 558 Handbuch
Stevens Aero Model
Stevens Aero Model LiddleGee 2.4 Betriebsanleitung
Stevens Aero Model
Stevens Aero Model CAP 232 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model S-Pou! 300 Handbuch
Stevens Aero Model
Stevens Aero Model microMAX 103 Handbuch
Stevens Aero Model
Stevens Aero Model Build It! FullHouse 500 Handbuch
Stevens Aero Model
Stevens Aero Model 1911 Nieuport Handbuch
Stevens Aero Model
Stevens Aero Model Pober Pixie 360 Handbuch
Stevens Aero Model
Stevens Aero Model SkyBoy 600 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model PACEMAKER Handbuch
Stevens Aero Model
Stevens Aero Model Build It! PuddleBug UM Handbuch
Stevens Aero Model
Stevens Aero Model SE5.a Handbuch
Stevens Aero Model
Stevens Aero Model FreDe 2X Handbuch
Stevens Aero Model
Stevens Aero Model RV-4 Bedienungsanleitung
Stevens Aero Model
Stevens Aero Model 1928 Pietenpol SkyScout Handbuch
Stevens Aero Model
Stevens Aero Model Scimon 30 Handbuch
Stevens Aero Model
Stevens Aero Model WaterBoard PondFlyer Bedienungsanleitung
