STIEBEL ELTRON Hydro-Shark SH3-07 Bedienungsanleitung

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

HYDRO-SHARK®3

MODULATING MICRO BOILERS

Radiant Floor Heating Applications

INSTALLATION INSTRUCTIONS FOR THE LICENSED PLUMBER & ELECTRICAN

MODEL #’S:

• SH3-07

• SH3-10

MODEL #’S:

• SH3-12

• SH3-14

• SH3-19

• SH3-24

MODEL #’S:

• SH3-29

• SH3-36

Warning: Not to be used with potable water systems

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

Table of Contents

Important

General

Mounting the units

Fluid connections

Electrical connections

Technical data

Troubleshooting

Spare parts

Warranty

Electrical & Mechanical Diagrams

Filling the System

4-5

7-9

13-19

20-23

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

IMPORTANT!

BOILERS ARE TO BE USED FOR RADIANT FLOOR HEATING ONLY!

THIS MANUAL MUST BE READ CAREFULLY BEFOREATTEMPTING TO INSTALL THE HYDRO-SHARK

BOILERS. IF YOU DO NOT FOLLOW THE SAFETY RULES OR THE INSTRUCTIONS OUTLINED IN THIS

MANUAL, THE UNIT MAY NOT OPERATE PROPERLY AND IT COULD CAUSE PROPERTY DAMAGE,

SERIOUS BODILY INJURYAND/OR DEATH.

STIEBEL ELTRON, INC. WILL NOT BE LIABLE FORANY DAMAGES BECAUSE OF FAILURE TO COMPLY

WITH INSTALLATION AND OPERATING INSTRUCTIONS OUTLINED IN THIS MANUAL OR BECAUSE

OF IMPROPER USE. IMPROPER USE INCLUDES THE USE FOR THIS APPLIANCE TO HEATANY LIQUID

OTHER THAN WATER OR PROPYLENE GLYCOL. FALURE TO COMPLY WITH THE INSTALLATION AND

OPERATING INSTRUCTIONS OR IMPROPER USE VOIDS THE WARRANTY. NEVER REMOVE THE

UNITS FRONT COVER UNLESS POWER IS TURNED OFF.

IF YOU HAVEANY QUESTIONS REGARDING THE INSTALLATION OR OPERATION OF THES BOILER,

PLEASE CALL OUR TECHNICAL SERVICE LINE AT 800-582-8423 (U.S.A. AND CANADA ONLY). IF YOU

ARE CALLING OUTSIDE OF THE U.S.AND CANADA CALL (413)-538-7850AND WE WILL REFER YOU TO

A QUALIFIED STIEBEL ELTRON SERVICE REPRESENTATIVE IN YOUR AREA.

GENERAL

• The output of heat from the boiler is electronically controlled. The Boiler will deliver any water

tempeture between 86° F and 140° F for the SH3-12,SH3-14, SH3-19, SH3-24, SH3-36 and

120° F for the SH3-07 and SH3-10. Please set the desired water delivery tempeture using the knob

on the front cover.

• When the Power light is ﬂashing, full element power is being applied. When the Power light is not

ﬂashing, the element power is being modulated to the water delivery temperature.

• Recommended Setting for radiant ﬂoor heating in cement or gypcrete is 110° F to 125° F.

• Recommended Setting for staple up or baseboard 140° F.

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

MOUNTING THE UNIT

SH3-12, SH3-14, SH3-19, SH3-24, SH3-29 & SH3-36

UNIT MUST BE INSTALLED IN A VERTICAL POSITION WITH THE WATER FITTINGS

POINTING DOWNWARD, DO NOT INSTALL UNIT WHERE IT WOULD ROUTINELY

BE SPLASHED WITH WATER OR ELECTRICAL SHOCK MAY RESULT.

1. Leave a minimum of 5” of Clearance on all sides for servicing.

2. Make sure that the Power is Off.

3. Remove the Cover.

4. Mount securely to wall by putting four screws through mounting holes.

5. Screw and plastic wall anchors for mounting on masonry or wood are provided.

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

MOUNTING THE UNIT

SH3-3 & SH3-10

UNIT MUST BE INSTALLED IN A VERTICAL POSITION WITH THE WATER FITTINGS

POINTING DOWNWARD, DO NOT INSTALL UNIT WHERE IT WOULD ROUTINELY

BE SPLASHED WITH WATER OR ELECTRICAL SHOCK MAY RESULT.

1. Leave a minimum of 5” of Clearance on all sides for servicing.

2. Make sure that the Power is Off.

3. Remove the Cover.

4. Mount securely to wall by putting four screws through mounting holes.

5. Screw and plastic wall anchors for mounting on masonry or wood are provided.

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

FLUID CONNECTIONS

NOTE: EXCESSIVE HEAT FROM SOLDERING COPPER PIPES NEAR THE BOILER MAY CAUSE DAMAGE.

1. All plumbing work must comply with the national, state, local & any other applicable codes.

2. Make sure the radiant ﬂoor system has been purged & is free of ﬂoating debris.

3. The return side (inlet) is on the right side of the unit, the supply side (outlet) is on the

left of the unit.

4. Apressure & temprature relief valve should be installed on the hot water supply side

(outlet) of the unit.

5. The boiler is designed for a connection to copper tubing and/or PEX tubing. If soldering the

unit is necessary, please direct the ﬂame away from the housing of the unit to avoid damage.

6. When all plumbing work is completed, check for leaks & take corrective action

before proceeding.

SUPPLY OUTLET RETURN INLET

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

ELECTRICAL CONNECTIONS

WARNING: BEFORE BEGINNING ANY WORK ON THE ELECTRIC INSTALLATION, BE SURE THAT

THE MAIN BREAKER PANEL SWITCHES ARE “OFF” TO AVOID ANY DANGER OF ELECTRIC SHOCK.

ALL MOUNTINGAND PLUMBING MUST BE COMPLETED BEFORE PROCEEDING WITH ELECTRICAL

HOOK-UP. WHERE REQUIRED BYLOCAL,STATE OR NATIONALELECTRICALCODES THE CIRCUITS

SHOULD BE EQUIPPED WITH A“ GROUND FAULT INTERRUPTER”.

1. All electrical work must comply with the national, state, local & any other applicable codes.

2. The boiler should be connected to properly grounded dedicated branch circuits of proper

voltage rating. Ground must be brought to the ‘Ground’ at the circuit breaker panel.

3. ASH3-07, SH3-10 & SH3-12 can be connected to ONE independent circuit (FigureA& B).

4. ASH3-14, SH3-19 & SHE-24 can be connected to TWO independent circuits (Figure C).

Use supply table (See Technical Data table “A” on page XX). Protected by TWO double pole

breakers sized for the load.

5. ASH3-29,SH3-36 can be connected to THREE independent circuits (Fig D.). Use supply

cable (See Technical Data Table “A”) protected by THREE double pole breakers sized

for the load.

6. Cut the electrical connection cable to length and strip.

7. The wire must be fed through the knockouts located between the Supply and Return ﬂuid

connections. The “Live” wires must be connected to the slots on the terminal block marked

“L” and “L”. The ground wire must be connected to slot marked with the ground symbol.

8. Reinstall the cover screws.

WARNING! As with any electrical appliance, failure to electrically ground may result in serious injury or Death.

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

Figure B

SH3-12

Figure A

SH3-07 & SH3-10

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

SH3-29,SH3-36 SH3-14,SH3-19,SH3-24 SH3-12

SH3-36 SH3-29

SH3-24 SH3-14, SH3-19 SH3-12

PHONE: 800-355-4945 WEB: www.energyproducts.biz

EMAL: [email protected]

“A” MODEL - 14 1/4 H X 7 7/8 W X 4 1/8 D - 1/2 PLUMBING FITTINGS

MODEL KW BTU VOLTS AMPS BRKR WT-LBS

SH3-07 7.2 24,573 240 30 (1)40 5.9

SH3-10 9.6 32,764 240 40 (1)50 5.9

“B” MODEL - 14 1/2 H X 16 5/8 W X 4 5/8 D - 3/4 PLUMBING FITTINGS

MODEL KW BTU VOLTS AMPS BRKR WT-LBS

SH3-12 12 40,968 240 50 (1)70 17

SH3-14 14.4 49,161 240 60 (2)40 20

SH3-19 19.2 65,548 240 80 (2)50 20

SH3-24 24 81,936 240 100 (2)70 20

“C” MODEL - 14 1/2 H X 16 5/8 W X 4 5/8 D 3/4 PLUMBING FITTINGS

MODEL KW BTU VOLTS AMPS BRKR WT-LBS

SH3-29 28.8 98,323 240 120 (3)50 24

SH3-36 36 122,904 240 150 (3)70 24

NOTE:

1. Boilers are considered a continuous load.

2. Copper conductors only.

TECHNICAL DATA

SERVICEBULLETIN:PolaritymattersontheHydro-SharkModelswithmultiplecircuits.Onmodels

Sh3-14,19,24,29and36thepolarityofL1/L2maters.IftheinstallerplacesL1ontheleftsideofcircuit

1,thanL1hasto beplacedontheleftsideofcircuit2(SH3-14,19,24) andcircuit3(SH3-29,36).

It does not matter if L1 or L2 is placed on the left or right side on the wireing block. It only

maters that all circuits are wired consistently, with L1 either always on the left or always on

the right. If the boiler will not run, reverse the L1 and L2 wires on one or two of the wiring

block to make the “polarity” consistent. The Factory is making changes to the interior wiring

so that the L1/L2 Polarity will not mater in the future. -May 14,2009

Andere Handbücher für Hydro-Shark SH3-07

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere STIEBEL ELTRON Kessel Handbücher

STIEBEL ELTRON

STIEBEL ELTRON SHW 200 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 751 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON EBK 5 G Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON EBK 5 G Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBP 200 E Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 302 WP Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SNU HOT Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBP 100 classic Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DEL 13 Plus AU Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHO AC 600 7,5 Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON HOT 2.6 N 1600 Premium Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON EVS15 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SNU 5 SL antitropf comfort Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON SBB 300 Trend Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SH 30 S Kurzanleitung

STIEBEL ELTRON

STIEBEL ELTRON HydroShark 115NG Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON KA 5 eltroboil Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 301 WP Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON PSH-H 30 Trend Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HOT 2.6 N Premium Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON KA 10 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HydroShark 7 Kurzanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 751 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 300 WP Trend Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung