STIEBEL ELTRON IS 5-1 E Bedienungsanleitung

This water heater must be installed (water and electrical installation),

commissioned and serviced by approved service technicians in

accordance with these instructions.

Este calentador de agua debe ser instalado (instalación eléctrica y de agua),

revisado y puesto en servicio por técnicos certicados de acuerdo a estas

instrucciones.

English

Instantaneous shower water heater - Operation and installation instructions

Español

Calentador de ducha instantáneo – Instrucciones de instalación y uso

IS 5-1 E / 5-2 E / 7-2 E

STIEBEL ELTRON

1. Operating Instruction for the user and the qualied installer

1.1 Description of the unit

The Stiebel Eltron IS pressureless

(open) instantaneous water heater is

a device for heating water for shower.

The electrical power is electronically

controlled. The unit switches the

power on once the ow volume

reach 1.5-2 l/min.

The “Power” light (C) indicates

that the unit is switched on. If the

temperature adjustment rotary

(B) switch is turned to the left, it is

possible to take a cold shower (the

heating will not be switched on).

The IS is tted with an overheating

protection device. In the event of

overheating the heating power will

be cut o.

This appliance is not intended

for use by persons (including

children) with reduced physical,

sensory or mental capabilities, or lack

of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the

appliance by a person responsible for

their safety.

Children should be supervised

to ensure that they do not

play with the appliance.

1.2 The essentials - in brief (Fig 1)

A) Water valve

B) Rotary control for temperature

adjustment

C) “Power” light

D) Shower accessories

English

Fig 1

Shower head level must not be higher than the unit.

STIEBEL ELTRON 3

English

1. Operating Instruction for the user and the qualied installer

1.3 Important information

The unit is optionally equipped

with an ELSD (Type IS..E only)

It is recommended to test the ELSD

one time per month.

How to test:

Switch on the electrical supply.

Press the Test button, the Trip light

will go on. Press the Reset button.

Warning!

If the Trip light activate after

reset or if the light activate during

shower, never try to x it. Contact

your dealer for a check and repair.

1.5 Technical Data

Warning!

If, during a shower , the

water valve is closed, (such as

applying soap to the body), then

valve opened again, high water

temperature may occur, to avoid risk

of scalding, stay any from the shower

head discharge zone momentarily.

The unit must not be put

under pressure. The outlet

of the unit is also used as a vent. A

periodical scale removal is essential

for the function of the shower head.

1.4 Hot water capacity

The hot water capacity depends on

the power of the unit, the cold water

temperature, and the ow volume.

Type IS 5-1 E IS 5-2 E IS 7-2 E

Design Open outlet

Min. inlet water pressure MPa(bar) 0.015(0.15)

Max. inlet water pressure MPa(bar) 0.5(5)

Cold water connection G½”

Electrical connection 1/N/PE/AC 115...127V 1/N/PE/AC 208...240V

Recommended circuit breaker 50 A 25 A 30 A

Recommended cable size 8 AWG 12 AWG 10 AWG

Voltage (V)

Rated Power (kW)

Rated current (A)

115 120 127

4.6 5.0 5.6

40 41.7 44

208 220 240

4.1 4.5 5.4

19.5 20.5 22.5

208 220 240

5.3 6.0 7.1

25.7 27.3 29.6

Note:

The cable sizes can only be a guiding value. Always abide by the corresponding

local standards, laws and regulations.

Stiebel Eltron cannot be held liable for any damages.

STIEBEL ELTRON

English

1.6 Important note

All the information in these

Operating and Installation

Instructions must be carefully

followed. These instructions provide

important details regarding the

safety, operation,

installation, and

maintenance of the unit.

The outlet must not be

connected to any tab or

tting other than those specied

1.7 Regulations and Provisions

- Regulations of the local power

supply company should be

observed.

- Regulations of the water supply

company should observed

- Technical data.

- Install the unit ush with the wall

- Electrical connection to be secure.

The device must be capable

of being isolated from the

mains, for example by fuses, with an

isolating distance of at least 3.5 mm.

in all poles.

If the supply cord is damaged,

it must be replaced by the

manufacturer, its service agent or

similarly qualied persons in order to

avoid a hazard.

The unit must be earthed

(see circuit diagram). To

protect against water penetration,

the cable seal (2) must be used.

1.8 Installation location

The shower unit is to be

installed in a closed, frost-free

room (disconnected units are to be

1. Operating Instruction for the user and the qualied installer

stored in a frost-free location, since

there will always be some water left

in the unit) The IS is to be installed

vertically on a wall (hot water

connection downwards).

1.9 First operation

(Only to be carried out by a qualied

installer)

Before switching on, set the

rotary water valve to“Max”

setting until the pipework and the

unit are free of air.

- Check theoperation of the water heater.

- Before switching “ON” set the rotary

temperature to “OFF”

Handing over the unit

Explain to the user how the unit works

and familiarise him or her with its use.

- Advise the user about possible

hazards (high water temperature)

- Hand over these instructions, to

be kept in a safe place.

1.10 Care and Maintenance

All that is needed for the housing is a

damp cloth. Do not use any abrasive

cleaning agents or agents containing

solvents.

Maintenance work may only

be carried out by a qualied

installer.

1.11 Service note

When carrying out any work,

isolate the unit from the mains

and shut o the water connection.

- Clean the lter

Disconnect water valve (17), remove

lter (14) and clean. Re-assemble

in reverse order.

STIEBEL ELTRON 5

English

2. Guarantee

3. Fault elimination for the user

For guarantees please refer to the

respective terms and conditions of

supply for your country.

The installation, electrical

connection and rst

operation of this appliance should be

carried out by a qualied installer.

The company does not accept liability

for failure of any good supplied

which have not been installed and

operated in accordance with the

manufacturer’s instructions.

Fault Cause Rectication

No hot water despite ow volume

setting at

“Trip” - light on

The water ow volume

required for the unit to

turn on has not been

reached.

- The shower head is

blocked with

dirt or limescale.

- Flow volume too low.

- ELSD activated

- Clean shower head

or remove limescale.

- Increase ow volume.

- Press“Reset”- button.

The unit is not being switched

on. Electricity supply and ow

available.

The water ow volume

required for the unit to

turn on has not been

reached.

- Filter in the cold water

connection pipeblocked

with dirt.

- Water pressure not

enough

- Clean the lter after

shutting o the cold

water intake.

- Increase mains

pressure

4 x 35 mm

6 mm

min. 4.5 mm

max. 5.5 mm

6 mm

210

350

275.28

100.02

100

115 mm

50 mm

Wiring diagram

Type IS 5-1 E

Type IS 5-2 E , IS 7-2 E

A - Heating Element

B - Electronic control set

C - Double Triac Set

D - Double action Thermostat

A - Heating Element

B - Electronic control set

C - ELSD Circuit

D - Triac Set

E - Thermostat

F - Button Board

G - Current Leakage Sensor

STIEBEL ELTRON

English

4. Installation Instruction for the qualied installer

Fig 2

Fig 4 Fig 5 Fig 6

Fig 7

Fig 3

514

STIEBEL ELTRON 7

4. Installation Instruction for the qualied installer

English

4.1 Description of the unit

1 Double action thermostat

2 Cable duct for electrical

connection

3 Power light

4 Rotary control for temperature

adjustment

5Hot water connection for

shower hose

6 Cold water connection

7 Lower fixing hole

8 Position for electrical connection

9 Upper fixing hole

10 Connection cable (Fig 5)

11 Cover securing screw (Fig 3)

12 Depthformounting screw (Fig 4)

13 Rear wall installation (Fig 6)

14 Combination filter

15 Washer

16 Union nut and washer, provide

by client

17 Water valve

18 ELSD (option)

Fig 8

STIEBEL ELTRON

4.2 Installing the unit

1. Flush the cold water pipe

thoroughly.

2. Fit a secure connection cable (10

ensure dimensions are correct).

3. Release cover securing screw (11).

4. Remove cover.

5. Determine the position of the

drill holes and drill the holes.

Insert the wall plugs and screw in

the screws (ensure screw insertion

depth is correct, 12).

6. Feed the connection cable through

the cable seal (2) in the rear wall.

Guide the unit over the wall

securing screws and slide it

downwards (13).

7. Fit the cold water connection.

Connect the water valve (17) with

the lter (14) and the washer (15)

to the cold water inlet of the unit

(6). Tighten the union nut and

washer (16) to the water valve.

8. Straighten the unit and tighten

the screws.

9. Connect the electrical supply.

10. Fit the cover and secure with the

screw.

11. Turn the rotary control (B) to the

left and right (internal setting

lever will engage).

12. Fit the shower accessories to the

unit.

4. Installation Instruction for the qualied installer

English

STIEBEL ELTRON 9

1. Instrucciones de uso para el usuario y el instalador certicado

1.1 Descripción de la unidad

El calentador de agua instantáneo

sin presión interna de Stiebel Eltron

es un una unidad para calentar

agua para la ducha. La intensidad

de la unidad está controlada

electrónicamente. El ujo se abre

o se cierra usando la válvula de

entrada. La unidad se enciende

cuando el ujo alcanza 1.5-2l/

min. El indicador de “energía”(C) se

enciende cuando la unidad se activa.

Si el control de temperatura (B) se

gira hacia la izquierda, es posible

tomar una ducha fría(la resistencia

no estará activa). La ducha IS cuenta

con un sistema de prevención de

sobrecalentamiento. En caso del

mismo, se desactivará el calor en la

resistencia.

1.2 Información básica- resumen

A Válvula de agua

B Control rotatorio para ajuste

de temperatura

C Indicador de encendido

D Accesorios de ducha

1.3 Información importante

Esta unidad no debe ser

instalada a presión. La salida

de la unidad también es utilizada

como ventilación. Una eliminación

peródica de residuos de aguas duras

es esencial para el funcionamiento de

la ducha a lo largo del tiempo.

La unidad está equipada de

manera opcional con

un ELSD (sólo modelo IS…E). Se

recomienda probar el ELSD una vez

al mes..

Cómo probar:

Encienda la corriente eléctrica.

Presionar el botón de Test, la luz

indicadora se encenderá. Presionar el

botón de Reset.

Atención!

Si la luz indicadora está activa

después del Reset o si dicha luz está

activa durante el uso de la ducha,

no intente repararla. Contacte con

su distribuidor o técnico para su

comprobación y reparación.

Atención!

Si durante la ducha, la

válvula de agua está cerrada(por

ejemplo, mientras aplicamos el

jabón), y posteriormente se abre,

puede salir agua a temperaturas

muy altas. Para evitar riesgo de

quemarse, apártese de la dicha

momentáneamente.

1.4 Cuidado y Mantenimiento

Lo único que necesita para la

cobertura es un trapo húmedo.

No utilice productos de limpieza

abrasivos o que contengan disolventes

Trabajo de mantenimiento

debe ser realizado

únicamente por un instalador

cualicado.

Español

STIEBEL ELTRON

1. Instrucciones de uso para el usuario y el instalador certicado

1.5 Capacidad de agua caliente

La capacidad de agua caliente

depende de la potencia de la unidad,

de la temperatura del agua entrante

y del volumen del ujo entrante.

- Este calentador no

está diseñado para su uso

por personas(incluidos niños) con

capaciadades físicas, sensoriales o

mentales reducidas, o insuciente

experiencia o conocimiento, a no ser

que hayan recibido instrucciones para

el uso de este aparato por la persona

responsable de su seguridad.

- Los niños deben ser

supervisados para asegurarse

de que no juegan con la unidad.

1.6 Datos Técnicos

(Se aplica la información en la placa de datos de la unidad)

Los tamaños

de cables son únicamente valores orientativos. Se deben tener en cuenta los

correspondientes estándares, normas, leyes y reglamentos locales. Stiebel Eltron

no se hace responsable de posibles daños y perjuicios.

Español

Tipo IS 5-1 E IS 5-2 E IS 7-2 E

Diseño Sistema abierto

Min. la presión del agua de entrada MPa (bar)

0.015(0.15)

Max. la presión del agua de entrada MPa (bar)

0.5(5)

Conexión de agua ( Ø Tuberia) G ½“

Conexión eléctrica 1/N/PE/AC 115...127V 1/N/PE/AC 208...240V

Tamaño Mínimo Requerido

del Interruptor Auto. “Breaker”

50 A 25 A 30 A

Cable AWG Cobre 8 AWG 12 AWG 10 AWG

Voltaje (V)

Vatios (kW)

Amperaje (A)

115 120 127

4.6 5.0 5.6

40 41.7 44

208 220 240

4.1 4.5 5.4

19.5 20.5 22.5

208 220 240

5.3 6.0 7.1

25.7 27.3 29.6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere STIEBEL ELTRON Boiler Handbücher

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHH 12 Si control Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON AQ 35 E Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHC 3-1 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DX 35 E Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HDB-E 12 Si Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SN 5 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON UFP 5 t Si Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHM 3 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON UFP 5 t Si Anleitung zur Verwendung

STIEBEL ELTRON

STIEBEL ELTRON SHZ 30 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHU 5 SLi comfort Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHC 2.5 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SH 10 SL Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHB-E 11 SLi electronic Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HDB-E 12 Si Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SH 10 SL Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DCE 10 Plus Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON IS 35 E Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHB-E 11 SLi electronic Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHC 6 XG Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DNM 3 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SNU 5 SL antitropf comfort Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHC 3-1 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung