Stinger STXJLPOD Bedienungsanleitung

STXJLPOD Installation Guide

STXJLPOD

2018- 2022 Jeep Wrangler JL / Gladiator JT

6.5" Speaker Pods with Tweeter Adapters

Installation Guide

What’s In The Box

LH Speaker Pod X 1

Tweeter Mounting Plate X 2 Speaker Plug Adapter X 2

RH Speaker Pod X 1

STXJLPOD Installation Guide

Recommended Tools

Installation Notes

 Read this installation guide thoroughly before disassembling or

modifying the vehicle. Installation of this product requires technical skill,

experience and specialized tools. If in doubt, it’s recommended to have

it professionally installed by an authorized Stinger Dealer.

Nylon Trim Tools

Phillips Screwdriver

7, 10, 13mm Sockets

Ratchet

7mm Wrench

Vehicle Disassembly

1. Starting at the top, remove the

knee panel below the steering wheel

by pulling outward to release the

retaining clips, then work your hands

down the edges of the panel to

release the remaining clips and

remove the panel.

2. Remove the three Phillips/7mm

screws circled. Remove the two

10mm bolts indicated by the arrows.

The bolt on the left is behind the

horizontal bar facing down.

3. Starting on the exposed left-hand

side of the radio/climate control

panel, pull outward to release the

retaining clips.

STXJLPOD Installation Guide

4. Unplug the two connectors on

the backside of the radio/climate

control panel and remove.

5. Remove the two screws securing

the radio bezel to the sub-dash.

NOTE: If the vehicle has an

aftermarket radio, it may need to be

removed to complete disassembly

of the dash area.

6. Starting at the bottom, pull

outward to unclip the radio bezel,

working your way up the sides and

then release the top and remove the

bezel.

Vehicle Disassembly (cont.)

7. Remove the indicated screw

above the radio display that is

securing the upper dash pad.

8. Starting at either end, pull the

upper dash pad trim towards the

rear of the vehicle to release the

retaining clips from one side to the

other.

NOTE: These clips can be extremely

hard to remove and some may stay

in the dash and need to be removed

and placed back on the trim panel.

9. Remove the four screws along the

top of the instrument cluster bezel.

Pull outward on the bezel to

disengage bezel from lower retaining

clips and remove.

STXJLPOD Installation Guide

10. Remove the indicated screws at

the top of the light switch panel to

the left of the instrument cluster.

11. Unclip the left side of the upper

steering wheel trim.

Remove the indicated screw.

12. Using a trim tool, remove the

dash end cover on the driver's side.

13. Remove the 4 screws from the

driver's end panel.

NOTE: Unplugging the door harness

and unbolting the door stay will

allow the door to open freely and

allow easier access to the screws.

14. Using a 7mm wrench, remove

the lower screw on the driver's end

panel.

15. Remove the speaker enclosure

side screw indicated.

If you are having trouble accessing

this screw, read NOTE in Step 13.

Vehicle Disassembly (cont.)

STXJLPOD Installation Guide

16. Pull out (towards the door)

on the edge of the end panel

and release the alignment studs

indicated.

Then pull towards the rear to access

the back of the panel.

17. Unplug the headlamp switch

wire harness connector and remove

the panel.

18. Remove the 10mm bolt below

the speaker on the left side. Pull the

metal brace off the locator pin so it

can drop down and allow room to

remove the speaker enclosure.

19. Remove the screw at the top

of the speaker enclosure. The

enclosure should now be free.

20. Push down on the enclosure and

angle the top mounting tab passed

the sub-dash and outward.

21. Tilt the enclosure forward far

enough to access the speaker

connector on the backside of the

enclosure. Unplug the speaker

connector.

Vehicle Disassembly (cont.)

Inhaltsverzeichnis

Andere Stinger Autozubehör Handbücher

Stinger

Stinger DSI computer Bedienungsanleitung

Stinger

Stinger SG-3 Bedienungsanleitung

Stinger

Stinger HEIGH10 SRK-JK11H Bedienungsanleitung

Stinger

Stinger SPXULED Bedienungsanleitung

Stinger

Stinger VIP Bedienungsanleitung

Stinger

Stinger XLINK XFDB108 Bedienungsanleitung

Stinger

Stinger XL 112 Beilage

Stinger

Stinger HEIGH10 UN1810E-VX1 Bedienungsanleitung

Stinger

Stinger Heigh10 Bedienungsanleitung

Stinger

Stinger STXKBR4 Bedienungsanleitung

Stinger

Stinger SR-RUN10H Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung