Storage Canopy 33x40x12 Bedienungsanleitung

SHELTER ASSEMBLY

MANUAL

33x40x12 Container Shelter Single truss

PARTS LIST

Part Code

Description

Qty

Left base plate

Rigth base plate

Top bent tube

Middle bent tube

Sidewall bent tube

Connection purlin

Support tube

Clip

Lower tensioning tube for roof cover

2 Groups

Roof cover

Bolt M8x70

Bolt M10x80

Ropes

1 dozen

∮32 Plastic plug for end of tensioning tube

Ratchet strap (To tie down ratchet)

Angle seat

Ratchet

Bolt 12*30

SPECIFICATIONS

Width: 33 ft

Length: 40 ft

Height: 12 ft

IMPORTANT: READ MANUAL FIRST

Improper site preparation, assembly and maintenance may invalidate warranty and cause

unnecessary and costly mistakes. If you have any questions, contact your local dealer.

For an easy assembly process, we have identified each individual component with the part

code as indicated in the parts list. Please refer to the part code numbers and drawing to

ensure problem-free assembly.

It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re-

tighten once or twice again after a few months of use. This is important when assembled

during cold seasons (autumn and winter) because the fabric gets stiff in these weather

conditions. When the weather conditions become warmer, the fabric loosens and needs

to be re-tighten

It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on

its own.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set

up near snow drifts, in slippery places, in high winds, or wet locations.

2. All children should be kept away from the work area.

3. Don’t overreach. Always keep proper footing and balance.

4. Do not assemble under the influence of alcohol or drugs. Read warning labels on

medication prescriptions to determine if your judgment or reflexes are impaired

while taking them. If there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these

conditions are likely to occur. Remove the cover during hurricanes.

6. Be careful with power and heat sources. Do not keep heat sources near the

tarpaulin. Do not expose to open flame.

7. Be aware of personal safety during assembly and use. Be careful not to pinch your

fingers with clips and tubes when assembling: When using, make sure there is

adequate ventilation for any dangerous fumes.

EQUIPMENT AND TOOLS FOR INSTALLATION

1. Measuring tape

2. Alignment string

3. Step ladder

4. Welder

5. Sledgehammer

6. Wrench

7. Scissors

INSTALLATION PROCESS

A - BASE PLATES INSTALLATION

Please refer to the Figure 1 to place the base plates.

Figure 1

1. The measure must be taken from center to center of the base plates. Refer to the

diagram above and confirm the place of the base plates. ENSURE THAT THE

FOUNDATIONS ARE SQUARE.

2. All the base plates need to be welded on the Containers.

B - FRAME INSTALLATION (Refer to figure 2 for the full diagram)

Figure 2

1. Connect the Top bent tube (part code 1), the Middle Bent Tube (part code 2) and

the Sidewall Bent Tube (part code 3) with the Bolt M8x70 (part code 9); these

make one group of arches. Please NOTE the direction of the bolt. DO NOT install

the bolts on the top of the truss where the fabric will rest.

2. Insert one end of the assembled arch into one base plate and force the other end

of the arch into the opposite base plate. Secure the arches to the base plates using

the bolts.

Figure 3

3. After installing the first two arches, connect the Connection purlin (part code 4)

onto them using the Bolt M10x80 (part code 10). There are 5 pieces of Connection

purlins (part code 4) between each arch.

4. Install the Support tube (part code 5) using the Clip (part code 6) and the Bolt

M8x70 (part code 9).

Figure 3

5. Then install the third arch into the base plate and connect the purlins.

6. Assemble the arches one by one until the frame is finished.

C - ROOF COVER INSTALLATION

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A

slight breeze is the most advantageous for cover installation. To take advantage of the

breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail

filled with air.

1. Insert the Lower tensioning tube (part code 7) into the pockets on the end of the

roof cover (part code 8). Then put the

∮

32 Plastic plug for end of tensioning tube

(part code 12).

Figure 4

2. Put the Roof cover (part code 8) EVENLY, CAREFULLY AND SLOWLY atop the frame.

Adjust the cover so that it is square and evenly centered on the frame.

Figure 5

3. On the Roof cover, cut pockets over each ratchet on the base plates, then use the

Ratchet strap (part code 13) to tie down the Lower tensioning tubes.

Figure 6

4. Weld the Angle seats (part code 14) on each container and use the Rope (part code

11) to knit the cover on the two external arches. Then tie the Rope to the Angle

seats.

Figure 7

Please, check our installation images and videos section by clicking the following link:

https://drive.google.com/drive/u/3/folders/1p9FLejo-JIrkJPx5_Kp-hDcssOph2dWa

NOTES:

-DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANYCIRCUMSTANCES until

the final assembly and tightening has been completed.

-The process is quite easy, but some tightening adjustments will be necessary to get

a flat, tensioned roof cover. Please adjust the roof cover every month.

-Wrap tape around the gap between the steel after installing.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Storage Canopy Unterschlupf Handbücher

Storage Canopy

Storage Canopy C4060DTR Bedienungsanleitung

Storage Canopy

Storage Canopy C3340DTR Bedienungsanleitung

Storage Canopy

Storage Canopy 40x60x15 ST Container shelter Bedienungsanleitung

Storage Canopy

Storage Canopy C4040DTR Bedienungsanleitung

Storage Canopy

Storage Canopy C6040S Bedienungsanleitung

Storage Canopy

Storage Canopy C3340S Bedienungsanleitung

Storage Canopy

Storage Canopy C4020 Bedienungsanleitung

Storage Canopy

Storage Canopy C3340DTPR Bedienungsanleitung

Storage Canopy

Storage Canopy C4060R Bedienungsanleitung

Storage Canopy

Storage Canopy FB408021DP Bedienungsanleitung

Storage Canopy

Storage Canopy FB408021P Bedienungsanleitung

Storage Canopy

Storage Canopy C2620R Bedienungsanleitung

Storage Canopy

Storage Canopy C2620 Bedienungsanleitung

Storage Canopy

Storage Canopy SHELTER Bedienungsanleitung

Storage Canopy

Storage Canopy W33 x L40 x H12 ft Bedienungsanleitung

Storage Canopy

Storage Canopy 40x40x15 Bedienungsanleitung

Storage Canopy

Storage Canopy Two Car Garage Shelter Bedienungsanleitung

Storage Canopy

Storage Canopy FB406021P Bedienungsanleitung

Storage Canopy

Storage Canopy C4040R Bedienungsanleitung

Storage Canopy

Storage Canopy C3340R Bedienungsanleitung

Storage Canopy

Storage Canopy 40x80x15 Bedienungsanleitung

Storage Canopy

Storage Canopy FB406021DP Bedienungsanleitung

Storage Canopy

Storage Canopy C3340 Bedienungsanleitung

Storage Canopy

Storage Canopy FB335017P Bedienungsanleitung

Beliebte Unterschlupf Handbücher anderer Marken

Tempo Fitness

Tempo Fitness S11 Bedienungsanleitung

Tuindeco

Tuindeco 42.7906 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1605 Bedienungsanleitung

TMG

TMG TMG-DT5040CG Bedienungsanleitung

TMG

TMG TMG-DT3063-PRO Bedienungsanleitung

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Bedienungsanleitung

Kampa

Kampa Poled Shelter 300 Bedienungsanleitung

Harnois

Harnois TA-R Bedienungsanleitung

Shelters4Less

Shelters4Less SR1551 Bedienungsanleitung

TMG

TMG TMG-DT50FW8 Bedienungsanleitung

Vikre Handel AS

Vikre Handel AS JIT-1216 Bedienungsanleitung

VARNA buildings

VARNA buildings C2020H Bedienungsanleitung

Frabill

Frabill ICE HUNTER 195 Bedienungsanleitung

Shelters4Less

Shelters4Less SR1588 Bedienungsanleitung

Sealey

Sealey Power Products GSS150819SD Bedienungsanleitung

Crivit

Crivit 104155 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1558-F Bedienungsanleitung

TMG

TMG TMG-ST3040C Bedienungsanleitung