Storage Canopy Two Car Garage Shelter Bedienungsanleitung

SHELTER

ASSEMBLY MANUAL

Two Car Garage Shelter

Parst List

Roof bent tube

Incline tube

Shoulder bent tube

Standing leg

Purlin

Supporting tube for roof frame

Base Plate

Base Plate at middle

Ratchet

Tension tube

Stake peg

Roof cover

Front and back cover

bolt 8*70mm

bolt 10*80mm

bolt 8*20mm

Rope

60 m

Nylon Band for Ratchet

Plastic cap

Supporting tube for arch frame

19A

Clip

SPECIFICATION

Width:22 Length: 24 Height: 11 ft

IMPORTANT ---- READ MANUALFIRST

Improper site preparation, Assembly and Maintenance may invalidate warranty and

cause unnecessary and costly mistake. If you have any questions contact your local

dealer.

For user friendly assembly we have identified each individual component with the part

code as indicated in the parts list. Please refer to the part code numbers and drawing to

ensure problem free assembly.

It’ s necessary to tighten the roof fabric enough to avoid “ hammocks” on the roof and

also re-tighten once or twice again after a few months of use. This is important when

assembly in cold weather (autumn and winter) because the fabric is stiff then and when

we got the sun and warm weather afterwards it will make the fabric “ slack”

again and need to be re-tighten before nextwinter.

It’ s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

Keep work area clean. Cluttered areas invite injuries. Do not set up near snow

drifts, in slippery places, in high winds, or wet location.

Keep children away. All children should be kept away from the workarea.

Don’ t over reach. Keep proper footing and balance at all times.

Do not assemble in under the influence of alcohol or drugs. Read warning labels on

prescriptions to determine if your judgment or reflexes are impaired while taking

drugs. If there is any doubt, do not assemble.

Be aware of possible windy conditions; fasten the bases in concrete if these

conditions are likely to occur. Remove the cover during hurricane.

Be careful with powerand heat sources. Do not keep heat sources near the tarpaulin.

Do not expose to open flame.

Be aware of personal safety during assembly and use. Be carful not to pinch fingers

with clips and tubes when assembling: when using makes sure there is adequate

ventilation for exhaust and other dangerous fumes.

EQUIPEMNT AND TOOLS FOR INSTALIATION

Measuring tape

String for alignment

Step ladder

Welder

Sledge hammer

Wrench

Scissors

INSTALLATION PROCESS

A—BASE INSTALLATION

Please refer to the diagram (Figure 1) to place the base plates. (UNIT: m)

Figure 1

1. The measure is from center to center of the tubes. Referring to the above diagram and confirm

the place of the base plates. ENSURE THAT THE FOUNDATIONS IS SQUARE.

2. There are two holes on the Base Plates, please using stake Pegs (No.10). THUS ALL BASE

PLATES ARE SECURED.

Note: The Stake Pegs apply for normal conditions, not suitable to the rock ground,

frozen soil and concrete ground.

、

Model: 222411P Frame Figure 2 (Size: W22 x L24 x H11 )

B--FRAME INSTALLATION

As Figure 3 shown find 1 piece of Roof Bent Tube (part code 1), 2 pieces of Incline Tube (part

code 2) 2 pieces of Shoulder Bent Tube (part code 3) and 2 pieces of Standing Leg Tube (Part No.

4). To connect them by using Bolt M8x70（part code 13）, which makes one group of peak arch.

Please NOTE the direction of the screw. DO NOT install the bolts on the top of the truss where the

fabric will rest.

Figure 3

Insert two end of the assembled peak arch into one base plate and force the other end of the peak

arch into the opposite base plate, fix them using Bolt M8x70mm（part code 13）.

Figure 4

After finishing installing the first two groups of peak arches, connect the Connection Tube (part

code 5) and Supporting tube for roof frame (Part No 6) onto them by using Bolt M10x80mm

（part code 14）. Then install the third group into base plate and connect the connection tubes,

there are 5 groups of peak arches and 5 pieces ofconnection tubes between each two groups. Finally

install the Diagonal Bracing Tube (part code 19) using Clip（part code 19A）asFigure No

2. By turns the assembly of the main frame is finished.

C--END DOORS ATTACHED

Figure 5

Door frame: Connect all the tube for door frame and fix them by using right bolts.

Put on the front and back covers (Part No. 12) refer to the Figure 5 and knit the cover by using

rope (No.16).

D- Install the Roof Cover

Figure 6

NOTE: DO NOT install the

cover onto the frame of your

building in high wind

conditions. A slight breezeis

the most advantageous for

cover installation. To take

advantage of the breeze,

pull the cover up over the

arches with the breeze

blowing in the cover like a

sail filled with air.

Put the Roof cover (part

code 11) EVENLY,

CARRFULLR AND

SLOWLY on the frame.

Adjust the cover so that it is square and evenly centered on the frame.

Use Rope (part code 21) to knit the cover on the two sides of the peak arches through all the

holes.

Cut 3 pockets according to the position of the base plates and insert the Lower Tension Tubes

(part code 9) into the pocket of roof cover. Then use the Ratchet (part code 8A) to fix the

Lower tension tubes like the Figure 7. Finally install the Plastic plug (part code 18) for into

two ends of the Lower tension tubes. Loosely secure the Nylon Band (No.17) in the ratchet on

the base plates. DO NOT TIGHTEN. Finally adjust the cover so that it is square and evenly

centered on the frame.

NOW THE INSTALLATION IS FINISHED, PLEASE ASJUST THE BASE PLATES VERY MONTH.

Figure 7

The process is

quite easy. But

some tightening

adjustments will

be necessary to

produce a flat,

tension roof

cover. Please adjust the roof cover every month or windy day.

Inhaltsverzeichnis

Andere Storage Canopy Unterschlupf Handbücher

Storage Canopy

Storage Canopy 40x80x15 Bedienungsanleitung

Storage Canopy

Storage Canopy C3340 Bedienungsanleitung

Storage Canopy

Storage Canopy C2620R Bedienungsanleitung

Storage Canopy

Storage Canopy C4040 Bedienungsanleitung

Storage Canopy

Storage Canopy C2620 Bedienungsanleitung

Storage Canopy

Storage Canopy W33 x L40 x H12 ft Bedienungsanleitung

Storage Canopy

Storage Canopy C4060R Bedienungsanleitung

Storage Canopy

Storage Canopy C3340DTPR Bedienungsanleitung

Storage Canopy

Storage Canopy DT Container shelter Bedienungsanleitung

Storage Canopy

Storage Canopy C4040S Bedienungsanleitung

Storage Canopy

Storage Canopy 26x40x10 Container Shelter Single truss Bedienungsanleitung

Storage Canopy

Storage Canopy C3340R Bedienungsanleitung

Storage Canopy

Storage Canopy C4040S Bedienungsanleitung

Storage Canopy

Storage Canopy 40x40x15 Bedienungsanleitung

Storage Canopy

Storage Canopy FB408021DP Bedienungsanleitung

Storage Canopy

Storage Canopy C4040DTR Bedienungsanleitung

Storage Canopy

Storage Canopy C2640R Bedienungsanleitung

Storage Canopy

Storage Canopy C6040S Bedienungsanleitung

Storage Canopy

Storage Canopy 33x40x12 Bedienungsanleitung

Storage Canopy

Storage Canopy EWC6040DTR Bedienungsanleitung

Storage Canopy

Storage Canopy C4080S Bedienungsanleitung

Storage Canopy

Storage Canopy FB406021P Bedienungsanleitung

Storage Canopy

Storage Canopy C4020 Bedienungsanleitung

Storage Canopy

Storage Canopy FB406021DP Bedienungsanleitung

Beliebte Unterschlupf Handbücher anderer Marken

Tempo Fitness

Tempo Fitness S11 Bedienungsanleitung

Tuindeco

Tuindeco 42.7906 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1605 Bedienungsanleitung

TMG

TMG TMG-DT5040CG Bedienungsanleitung

TMG

TMG TMG-DT3063-PRO Bedienungsanleitung

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Bedienungsanleitung

Kampa

Kampa Poled Shelter 300 Bedienungsanleitung

Harnois

Harnois TA-R Bedienungsanleitung

Shelters4Less

Shelters4Less SR1551 Bedienungsanleitung

TMG

TMG TMG-DT50FW8 Bedienungsanleitung

Vikre Handel AS

Vikre Handel AS JIT-1216 Bedienungsanleitung

VARNA buildings

VARNA buildings C2020H Bedienungsanleitung

Frabill

Frabill ICE HUNTER 195 Bedienungsanleitung

Shelters4Less

Shelters4Less SR1588 Bedienungsanleitung

Sealey

Sealey Power Products GSS150819SD Bedienungsanleitung

Crivit

Crivit 104155 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1558-F Bedienungsanleitung

TMG

TMG TMG-ST3040C Bedienungsanleitung