Storage Canopy 40x40x15 Bedienungsanleitung

SHELTER ASSEMBLY

MANUAL

40x40x15 ST Container shelter

PARTS LIST

Part Code

Description

Qty

Left base plate

Rigth base plate

Roof bent tube

Upside bent tube

Underside bent tube

Lower bent tube

Purlin

Inclined support tube

Clip for inclined support tube

Bolt M12x110

Bolt M10x100

112

Winch (ratchet?)

Belts for winch

Angle seats

Roof cover

Knitting rope for cover

∮32 Plastic plug for end of tensioning tube

Tensioning tube

Iron angle for base plate

Bolt 12x30

ANCHORING THE CONTAINER

Make sure you have:

•Welder.

•Cement.

•Four 3” x 3” x 6 feet ¼” Square steel angle

1. As shown in the diagram 1, make a 3 ft deep hole right beside one of the front and

opposite rear corners of the container, in which the 6ft square steel will be installed.

2. Insert the 6ft square steel into the hole, making sure 3ft is below the surface

completely laying on the side of the containers.

3. Weld the square steel to the 2 containers.

4. Pour cement in the holes to make sure the square steel won’t move.

5. Repeat the previous steps on the corners located in the opposite rear side.

Securing the containers to the floor is crucial, that way the containers won’t shift

under harsh weather conditions, thus avoiding the shipping container canopy roof top

of getting damaged.

Diagram 1

Highly Recommended

1. All container canopy covers need to be removed during windstorm of 60 mph,

leaving frame assembled. Customer responsibility.

2. All container canopy covers need to be removed before a snowstorm of 1-2 inches

(for single truss Shipping container roofs) and 3-4 inches (for double truss Shipping

container roofs), leaving the frame assembled. Customer responsibility.

3. It is highly recommended for customers who live in snow states and cities to use

double truss framing instead of Single truss framing. Customer responsibility.

4. It’s the owner's responsibility to shovel snow off the canopy rooftop.

5. All containers need to be anchored to the ground in each opposite corner sides.

Customer responsibility.

6. All of our products fall under the temporary structure category/storage ragtops.

Return Policy: Any product can be returned within 7 calendar days after arrival; shipping

expenses are not refundable. For more information, please refer to the Return and refund

policy page.

About lifespan:

Tarp lifespan: 7-10 years*

Frame Lifespan: +15 years*

*The term "lifespan" refers to the durability of the materials themselves, not to the

structural integrity of the canopy once assembled.

SPECIFICATIONS

Width: 40 ft

Length: 40 ft

Height: 15 ft

IMPORTANT: READ MANUAL FIRST

Life span is only on the is only on the material itself not on the installation on the canopy

structure. 7 to 10 years on the tarp and 15 years on the frame.

Improper site preparation, assembly and maintenance may invalidate warranty and cause

unnecessary and costly mistakes. If you have any questions, contact your local dealer.

For an easy assembly process, we have identified each individual component with the part

code as indicated in the parts list. Please refer to the part code numbers and drawing to

ensure problem-free assembly.

It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re-

tighten once or twice again after a few months of use. This is important when assembled

during cold seasons (autumn and winter) because the fabric gets stiff in these weather

conditions. When the weather conditions become warmer, the fabric loosens and needs

to be re-tighten

It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on

its own.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set

up near snow drifts, in slippery places, in high winds, or wet locations.

2. All children should be kept away from the work area.

3. Don’t overreach. Always keep proper footing and balance.

4. Do not assemble under the influence of alcohol or drugs. Read warning labels on

medication prescriptions to determine if your judgment or reflexes are impaired

while taking them. If there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these

conditions are likely to occur. Remove the cover during hurricanes.

6. Be careful with power and heat sources. Do not keep heat sources near the

tarpaulin. Do not expose to open flame.

7. Be aware of personal safety during assembly and use. Be careful not to pinch

your fingers with clips and tubes when assembling: When using, make sure there

is adequate ventilation for any dangerous fumes.

EQUIPMENT AND TOOLS FOR INSTALLATION

1. Measuring tape

2. Alignment string

3. Step ladder

4. Welder

5. Sledgehammer

6. Wrench

7. Scissors

INSTALLATION PROCESS

A - BASE PLATES INSTALLATION

Please refer to the Figure 1 to place the base plates.

Figure 1

1. The measure must be taken from center to center of the base plates. Refer to the

diagram above and confirm the place of the base plates. ENSURE THAT THE

FOUNDATIONS ARE SQUARE.

2. All the base plates need to be welded on the Containers.

B - FRAME INSTALLATION (Refer to figure 2 for the full diagram)

Figure 2

1. Connect the Roof Bent Tube (part code 1), the Upside Bent Tube (part code 2), the

Underside Bent Tube (part code 3) and the Lower Bent Tube (part code 4) with the

Bolt M10x100 (part code 9); these make one group of arches. Please NOTE the

direction of the bolt. DO NOT install the bolts on the top of the truss where the

fabric will rest.

2. Insert one end of the assembled arch into one base plate and force the other end

of the arch into the opposite base plate.

Figure 3

3. After installing the first two arches, connect the Connection purlin (part code 5)

onto them using the Bolts M12x110 (part code 8). There are 7 pieces of Connection

purlins (part code 5) between each arch.

4. Install the Inclined Support tube (part code 6) using Clip for Inclined Support Tube

(part code 7). Assemble the frame by turns like this.

Figure 4

5. Then install the third arch into the base plate and connect the purlins.

6. Assemble the arches one by one until the frame is finished.

C - ROOF COVER INSTALLATION

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A

slight breeze is the most advantageous for cover installation. To take advantage of the

breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail

filled with air.

1. Assemble Tensioning Tube (part code 16) before installing the cover. Insert the

Tensioning Tube (part code 16) into the pockets on the end of the roof cover (part

code 13). Then put the ∮32 Plastic plug (part code 15).

Figure 5

2. Put the Roof cover (part code 13) EVENLY, CAREFULLY AND SLOWLY atop the

frame. Adjust the cover so that it is square and evenly centered on the frame.

Figure 6

3. Cut pockets over each ratchet on the base plates and put the Tensioning Tube for

roof cover (part code 16) into the pocket of Roof cover. Then use the Nylon band

(part code 11) to tie down the Lower tensioning tubes as shown in Figure 6.

Figure 7

4. Weld the Angle seats (part code 12) on each container and use Rope (part code 14)

to knit the cover on the two side arches and tie the Roof cover to the Angle seats.

Figure 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Storage Canopy Unterschlupf Handbücher

Storage Canopy

Storage Canopy C3340S Bedienungsanleitung

Storage Canopy

Storage Canopy SHELTER Bedienungsanleitung

Storage Canopy

Storage Canopy FB406021DP Bedienungsanleitung

Storage Canopy

Storage Canopy C4060R Bedienungsanleitung

Storage Canopy

Storage Canopy C4040 Bedienungsanleitung

Storage Canopy

Storage Canopy 40x60x15 ST Container shelter Bedienungsanleitung

Storage Canopy

Storage Canopy C4060DTR Bedienungsanleitung

Storage Canopy

Storage Canopy 40x80x15 Bedienungsanleitung

Storage Canopy

Storage Canopy C3340R Bedienungsanleitung

Storage Canopy

Storage Canopy FB408021DP Bedienungsanleitung

Storage Canopy

Storage Canopy C2620R Bedienungsanleitung

Storage Canopy

Storage Canopy FB335017P Bedienungsanleitung

Storage Canopy

Storage Canopy C4040DTR Bedienungsanleitung

Storage Canopy

Storage Canopy C4040S Bedienungsanleitung

Storage Canopy

Storage Canopy C2620 Bedienungsanleitung

Storage Canopy

Storage Canopy EWC6040DTR Bedienungsanleitung

Storage Canopy

Storage Canopy C4020 Bedienungsanleitung

Storage Canopy

Storage Canopy C3340 Bedienungsanleitung

Storage Canopy

Storage Canopy DT Container shelter Bedienungsanleitung

Storage Canopy

Storage Canopy ST Container shelter Bedienungsanleitung

Storage Canopy

Storage Canopy Two Car Garage Shelter Bedienungsanleitung

Storage Canopy

Storage Canopy FB408021P Bedienungsanleitung

Storage Canopy

Storage Canopy C4040R Bedienungsanleitung

Storage Canopy

Storage Canopy 33x40x12 Bedienungsanleitung

Beliebte Unterschlupf Handbücher anderer Marken

Tempo Fitness

Tempo Fitness S11 Bedienungsanleitung

Tuindeco

Tuindeco 42.7906 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1605 Bedienungsanleitung

TMG

TMG TMG-DT5040CG Bedienungsanleitung

TMG

TMG TMG-DT3063-PRO Bedienungsanleitung

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Bedienungsanleitung

Kampa

Kampa Poled Shelter 300 Bedienungsanleitung

Harnois

Harnois TA-R Bedienungsanleitung

Shelters4Less

Shelters4Less SR1551 Bedienungsanleitung

TMG

TMG TMG-DT50FW8 Bedienungsanleitung

Vikre Handel AS

Vikre Handel AS JIT-1216 Bedienungsanleitung

VARNA buildings

VARNA buildings C2020H Bedienungsanleitung

Frabill

Frabill ICE HUNTER 195 Bedienungsanleitung

Shelters4Less

Shelters4Less SR1588 Bedienungsanleitung

Sealey

Sealey Power Products GSS150819SD Bedienungsanleitung

Crivit

Crivit 104155 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1558-F Bedienungsanleitung

TMG

TMG TMG-ST3040C Bedienungsanleitung