Storage Canopy DT Container shelter Bedienungsanleitung

SHELTER ASSEMBLY

MANUAL

40x80x15 DT Container shelter

Double Truss

PARTS LIST

Part Code

Description

Qty

Top bent tube

Side bent tube

Lower bent tube

Purlin

Top tensioning device

Clips

Left base plate

Right base plate

Ratchet

Nylon band for ratchet

Tensioning tube

2 groups

Bolts M8x70

176

Bolts M12x30

132

Bolts M10x80

Roof cover

Knitting rope for cover

Plastc plug

Angle seat

Iron angle for base plate

ANCHORING THE CONTAINER

Make sure you have:

•Welder.

•Cement.

•Four 3” x 3” x 6 feet ¼” Square steel angle

1. As shown in the diagram 1, make a 3 ft deep hole right beside one of the front and

opposite rear corners of the container, in which the 6ft square steel will be installed.

2. Insert the 6ft square steel into the hole, making sure 3ft is below the surface

completely laying on the side of the containers.

3. Weld the square steel to the 2 containers.

4. Pour cement in the holes to make sure the square steel won’t move.

5. Repeat the previous steps on the corners located in the opposite rear side.

Securing the containers to the floor is crucial, that way the containers won’t shift

under harsh weather conditions, thus avoiding the shipping container canopy roof top

of getting damaged.

Diagram 1

Highly Recommended

1. All container canopy covers need to be removed during windstorm of 60 mph,

leaving frame assembled. Customer responsibility.

2. All container canopy covers need to be removed before a snowstorm of 1-2 inches

(for single truss Shipping container roofs) and 3-4 inches (for double truss Shipping

container roofs), leaving the frame assembled. Customer responsibility.

3. It is highly recommended for customers who live in snow states and cities to use

double truss framing instead of Single truss framing. Customer responsibility.

4. It’s the owner's responsibility to shovel snow off the canopy rooftop.

5. All containers need to be anchored to the ground in each opposite corner sides.

Customer responsibility.

6. All of our products fall under the temporary structure category/storage ragtops.

Return Policy: Any product can be returned within 7 calendar days after arrival; shipping

expenses are not refundable. For more information, please refer to the Return and refund

policy page.

About lifespan:

Tarp lifespan: 7-10 years*

Frame Lifespan: +15 years*

*The term "lifespan" refers to the durability of the materials themselves, not to the

structural integrity of the canopy once assembled.

SPECIFICATIONS

Width: 40 ft

Length: 80 ft

Height: 15 ft

IMPORTANT: READ MANUAL FIRST

Improper site preparation, assembly and maintenance may invalidate warranty and cause

unnecessary and costly mistakes. If you have any questions, contact your local dealer.

For an easy assembly process, we have identified each individual component with the part

code as indicated in the parts list. Please refer to the part code numbers and drawing to

ensure problem-free assembly.

It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re-

tighten once or twice again after a few months of use. This is important when assembled

during cold seasons (autumn and winter) because the fabric gets stiff in these weather

conditions. When the weather conditions become warmer, the fabric loosens and needs

to be re-tighten

It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on

its own.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set

up near snow drifts, in slippery places, in high winds, or wet locations.

2. All children should be kept away from the work area.

3. Don’t overreach. Always keep proper footing and balance.

4. Do not assemble under the influence of alcohol or drugs. Read warning labels on

medication prescriptions to determine if your judgment or reflexes are impaired

while taking them. If there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these

conditions are likely to occur. Remove the cover during hurricanes.

6. Be careful with power and heat sources. Do not keep heat sources near the

tarpaulin. Do not expose to open flame.

7. Be aware of personal safety during assembly and use. Be careful not to pinch your

fingers with clips and tubes when assembling: When using, make sure there is

adequate ventilation for any dangerous fumes.

EQUIPMENT AND TOOLS FOR INSTALLATION

1. Measuring tape

2. Alignment string

3. Step ladder

4. Welder

5. Sledgehammer

6. Wrench

7. Scissors

INSTALLATION PROCESS

A - BASE PLATES INSTALLATION

Please refer to the Figure 1 to place the base plates.

Figure 1

1. The measure must be taken from center to center of the base plates. Refer to the

diagram above and confirm the place of the base plates. ENSURE THAT THE

FOUNDATIONS ARE SQUARE.

2. All the base plates need to be welded on the Containers.

B - FRAME INSTALLATION (Refer to figure 2 for the full diagram)

Figure 2

1. Connect the Top Bent Tube (part code 1), the Side Bent Tube (part code 2) and the

Lower Bent Tube (part code 3) with the Bolts M8x70 (part code 11); these make

one group of arches. Please NOTE the direction of the bolt. DO NOT install the

bolts on the top of the truss where the fabric will rest.

Figure 3

2. Insert one end of the assembled arch into one base plate and force the other end

of the arch into the opposite base plate.

Figure 4

3. After installing the first two arches, connect the Purlin (part code 4) onto them

using the Bolts M10x80 (part code 12). There are 7 pieces of Purlins (part code 4)

between each arch.

4. Install the Inclined Top tension device (part code 5) using the Clips (part code 6).

Figure 5

5. Then install the third arch into the base plate and connect the purlins.

6. Assemble the arches one by one until the frame is finished.

C - ROOF COVER INSTALLATION

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A

slight breeze is the most advantageous for cover installation. To take advantage of the

breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail

filled with air.

1. Insert the Tensioning tube (part code 10) into the pockets on the end of the roof

cover (part code 13). Then put the Plastic plugs (part code 15).

Figure 6

2. Put the Roof cover (part code 13) EVENLY, CAREFULLY AND SLOWLY atop the

frame. Adjust the cover so that it is square and evenly centered on the frame.

Figure 7

3. On the Roof cover, cut pockets over each ratchet on the base plates, then use the

Nylon band for ratchet (part code 9) to tie down the Tensioning tubes.

Figure 8

4. Weld the Angle seats (part code 16) on each container and use Knitting Rope for

Cover (part code 14) to knit the cover on the two side arches and tie the Knitting

Rope for Cover to the Angle seats.

Figure 9

Inhaltsverzeichnis

Andere Storage Canopy Unterschlupf Handbücher

Storage Canopy

Storage Canopy 40x80x15 Bedienungsanleitung

Storage Canopy

Storage Canopy SHELTER Bedienungsanleitung

Storage Canopy

Storage Canopy C604015S Bedienungsanleitung

Storage Canopy

Storage Canopy C2620 Bedienungsanleitung

Storage Canopy

Storage Canopy C4040S Bedienungsanleitung

Storage Canopy

Storage Canopy C3340 Bedienungsanleitung

Storage Canopy

Storage Canopy C4040S Bedienungsanleitung

Storage Canopy

Storage Canopy FB406021DP Bedienungsanleitung

Storage Canopy

Storage Canopy C2620R Bedienungsanleitung

Storage Canopy

Storage Canopy C3340DTPR Bedienungsanleitung

Storage Canopy

Storage Canopy C6040S Bedienungsanleitung

Storage Canopy

Storage Canopy C2640R Bedienungsanleitung

Storage Canopy

Storage Canopy C4040R Bedienungsanleitung

Storage Canopy

Storage Canopy C4060DTR Bedienungsanleitung

Storage Canopy

Storage Canopy Two Car Garage Shelter Bedienungsanleitung

Storage Canopy

Storage Canopy FB408021P Bedienungsanleitung

Storage Canopy

Storage Canopy 26x40x10 Container Shelter Single truss Bedienungsanleitung

Storage Canopy

Storage Canopy C3340R Bedienungsanleitung

Storage Canopy

Storage Canopy 40x60x15 ST Container shelter Bedienungsanleitung

Storage Canopy

Storage Canopy C4080S Bedienungsanleitung

Storage Canopy

Storage Canopy ST Container shelter Bedienungsanleitung

Storage Canopy

Storage Canopy 33x40x12 Bedienungsanleitung

Storage Canopy

Storage Canopy C4040 Bedienungsanleitung

Storage Canopy

Storage Canopy C3340DTR Bedienungsanleitung

Beliebte Unterschlupf Handbücher anderer Marken

Tempo Fitness

Tempo Fitness S11 Bedienungsanleitung

Tuindeco

Tuindeco 42.7906 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1605 Bedienungsanleitung

TMG

TMG TMG-DT5040CG Bedienungsanleitung

TMG

TMG TMG-DT3063-PRO Bedienungsanleitung

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Bedienungsanleitung

Kampa

Kampa Poled Shelter 300 Bedienungsanleitung

Harnois

Harnois TA-R Bedienungsanleitung

Shelters4Less

Shelters4Less SR1551 Bedienungsanleitung

TMG

TMG TMG-DT50FW8 Bedienungsanleitung

Vikre Handel AS

Vikre Handel AS JIT-1216 Bedienungsanleitung

VARNA buildings

VARNA buildings C2020H Bedienungsanleitung

Frabill

Frabill ICE HUNTER 195 Bedienungsanleitung

Shelters4Less

Shelters4Less SR1588 Bedienungsanleitung

Sealey

Sealey Power Products GSS150819SD Bedienungsanleitung

Crivit

Crivit 104155 Bedienungsanleitung

No Butts Bin

No Butts Bin SR1558-F Bedienungsanleitung

TMG

TMG TMG-ST3040C Bedienungsanleitung