StreamLight TLR-1 HL Bedienungsanleitung

User Manual of Product 1:

Streamlight 69260 TLR-1 HL 1000-Lumen Weapon Light with

Rail Locating Keys and Lithium Batteries, Box, Black

TLR-1

/ TLR-2

Series

Operating Instructions // Instrucciones de funcionamiento

Instructions d’utilisation // Bedienungsanleitung

IMPORTANT WARNINGS

WARNING: Use of light in “strobe” mode may cause seizure in persons with photosensitive epilepsy.

Night hunting with articial light may be prohibited or restricted in your state. Please check your state’s

game laws for clarication.

CAUTION: The TLR-1 HL®, TLR-2 HL®, TLR-2 HL®G and TLR-1 HPL®provide a powerful beam.

When operated for a long time, it will get uncomfortably warm. This is NORMAL and is not a defect.

Any LED ashlight of similar size and performance will produce similar amounts of heat during operation.

The only way to reduce operating heat is to SIGNIFICANTLY lower the output, or increase the size of

the ashlight. While this heating may trigger the drop reex if an unattended hot light is picked up, the

temperature does not present a burn hazard. When used tactically for short periods of time to clear a room,

check for intruders, etc., heating will not be a problem.

FAILURE TO READ AND FOLLOW THESE OPERATING INSTRUCTIONS AND WARNINGS WHEN

HANDLING A FIREARM OR THE TLR CAN BE DANGEROUS AND CAN RESULT IN SERIOUS INJURY,

DAMAGE TO PROPERTY, OR DEATH.

• Use of a rearm under any circumstance may be dangerous. SERIOUS INJURY OR EVEN DEATH may

result without proper training in the safe handling of rearms. Proper training should be obtained from an

accredited rearms safety program conducted by competent, qualied instructors in the military, police

academies or National Rie Association afliated instruction programs.

• Read your rearm’s manual before attaching your gun mounted light.

• Never point a rearm at something you are not willing to destroy.

• Streamlight recommends that the TLR should only be activated with the non-trigger hand while employ-

ing a two-hand grip on the rearm and with the trigger nger outside the trigger guard when possible.

Failure to do so could result in an accidental discharge and serious injury, damage to property, or death.

• Thoroughly practice (employing safe training conditions) with the TLR and rearm before using the

weapon in a tactical situation.

BEFORE ATTACHING, INSPECTING OR SERVICING A FIREARM-MOUNTED TLR

1. Engage the safety on the rearm if applicable.

2. Remove the magazine from the rearm if applicable.

3. Open the action and inspect the chamber to be sure it is empty.

IT IS IMPERATIVE THAT SAFETY MEASURES BE EMPLOYED AT ALL TIMES WHILE

HANDLING THE FIREARM.

BATTERIES

WARNING: FIRE, EXPLOSION, BURN HAZARD.

USE ONLY: Streamlight, Panasonic, or Sanyo size CR123A; Duracell 123A, or Energizer 123. Use of other

batteries or mixing of used and new or different brand batteries may result in leakage, re or explosion and

serious personal injury. DO NOT recharge, misuse, short circuit, improperly store or discard, disassemble,

or heat above 212°F (100°C). Keep away from children.

USE ONLY THOSE BATTERIES SPECIFICALLY RECOMMENDED FOR USE IN THIS PRODUCT.

LED (All Models inc. TLR-1®Game Spotter®)

Caution - LED Radiation (RG-2)

Do Not Stare Into Beam.

May Be Harmful To Eyes.

Per IEC 62471 Ed 1.0:2006-07

LASER/LED (TLR-2®/2®s/TLR-2 HL®) LASER/LED (TLR-2®G and TLR-2 HL®G)

Battery Installation/Removal

(TLR-2®Shown)

THE TLR MUST BE REMOVED FROM THE FIREARM BEFORE THE BATTERY

COMPARTMENT CAN BE OPENED OR CLOSED. 1- Unlock

(Apply force and push latch toward

key until latch touches body)

2- Swing Door Open

(After lifting door to

remove tab from slot)

3- Replace Batteries

(Polarity is indicated

on body of ashlight)

4- Insert Tab into Slot to Close Door

CAUTION - LASER/LED RADIATION

- CLASS 3R LASER PRODUCT

AVOID DIRECT EYE EXPOSURE

MAX OUTPUT: <5 mW

WAVELENGTH: 650 - 660 nm

- LED RADIATION (RG-2):

DO NOT STARE INTO BEAM.

MAY BE HARMFUL TO EYES.

AVOID EXPOSURE;

LASER RADIATION

IS EMITTED FROM

THIS APERTURE.

COMPLIES WITH 21 CFR 1040.10 AND 1040.11

AS AMENDED BY LASER NOTICE 50., 24JUNE07.

LASER/LIGHT LIGHT LASER

CAUTION - LASER/LED RADIATION

- CLASS 3R LASER PRODUCT

AVOID DIRECT EYE EXPOSURE

MAX OUTPUT: <5 mW

WAVELENGTH: 510 - 530 nm

- LED RADIATION (RG-2):

DO NOT STARE INTO BEAM.

MAY BE HARMFUL TO EYES.

AVOID EXPOSURE;

LASER RADIATION

IS EMITTED FROM

THIS APERTURE.

COMPLIES WITH 21 CFR 1040.10 AND 1040.11

AS AMENDED BY LASER NOTICE 50., 24JUNE07.

LASER/LIGHT LIGHT LASER

GREEN

2- Swing Door Open

(After lifting door to

remove tab from slot)

3- Replace Batteries

(Polarity is indicated

on body of ashlight)

5- Swing Door Closed

(Apply Force)

6- Lock

(Latch will stop against top of door)

Rail Keys

Four polymer rail keys (included) allow the TLR to be attached to a variety of rearms: GL - Glock or

“universal” rails, SW - TSW & 99, Beretta - 90two, Sig – P320, 1913 - Mil Std-1913 (Picatinny).

Each rail key is stamped for easy identication and

the keys share a common key screw and hex nut.

Each key has a hex nut cavity in the base.

1. Select the appropriate key and insert a hex

nut into the cavity in the base of the key.

Note: Adjust the hex nut so no portion

protrudes from the key.

2. Hold the rail key (hex nut side up) and the

TLR (key pocket side down) and align the two.

3. Insert the key into the TLR key pocket and

use a 7/64” hex wrench to secure it with the

key screw.

NOTE: A key MUST be used or the TLR will slide

off the front of the rail under recoil.

Hex Nut Cavity

Mounting/Removal Procedure

MAKE SURE THAT THE FIREARM IS UNLOADED AND THE BREECH IS OPEN. IT IS IMPERATIVE THAT

SAFETY MEASURES BE EMPLOYED AT ALL TIMES WHILE HANDLING THE FIREARM.

1. The TLR is designed to be quickly attached or detached from the side of the weapon or accessory rail.

2. Loosen the rail clamp tension bolt.

3. Angle the TLR, placing the xed portion of the rail clamp against the accessory rail and align

the rail key with the appropriate cross groove in the accessory rail.

4. Depress the tension bolt to open the rail clamp, rotate the TLR into place and

release the pressure on the tension bolt to “snap” the light in place.

5. Check for t and tighten tension bolt until the TLR is securely attached to the rearm.

A coin should be used to obtain sufcient tightness.

Rail Rail Key

Rail Groove

Rail

Key

Adjustable Portion

of Rail Clamp

Rail Clamp

Tension Bolt

Fixed Portion

of Rail Clamp

Switch Operation

(TLR-2®Shown)

The TLR features a paddle switch providing momentary or constant activation.

The TLR-2®series has an additional mode selection switch located on the rear of the laser housing.

Strobe Operation

The TLR-1®s, TLR-2®s, TLR-1 HPL®, TLR-1 HL®, TLR-2 HL®, TLR-2®G and TLR-2 HL®G feature a strobe

mode that can be activated by the paddle switch. Within 0.4 seconds, press the paddle switch into the

momentary position, release and immediately re-press and hold for strobe.

Strobe Enable/Disable

The TLR-1®s, TLR-2®s, TLR-1 HPL®, TLR-1 HL®, TLR-2 HL®, TLR-2®G and TLR-2 HL®G ship from the

factory with the strobe mode enabled.

The light can be reprogrammed to disable strobe by tapping the momentary paddle switch very rapidly

ten times and holding it down on the tenth time. Hold until the light turns off (about one second) which

indicates reprogramming was successful. Repeat the procedure above to re-enable the strobe mode.

NOTE: Activation of the strobe function is NOT recommended with the remote switch.

Strobe should be disabled.

Green Laser Operating Temperature Range

The green laser used in the TLR-2®G and TLR-2 HL®G employs the latest direct drive technology and

is not sensitive to temperature. The TLR-2®G and TLR-2 HL®G green laser will operate over the full

temperature range of the product from -40°F to 120°F.

TLR-2®Models Laser Sight Zeroing

For a laser mounted below or to the side of the bore, there is only one distance where the bullet path will

coincide with the laser sight line. This point is the “zero range.” Laser adjustment and the muzzle velocity

of the bullet determine where this point occurs. The user must decide how high above or below the sight

line the bullet can be allowed to strike and adjust the sight accordingly. At distances less than the zero

range the bullet will be above the sight line. Beyond the zero range the bullet will be below the sight line.

If mounted to the side, the bullet will also deviate to the side of the laser line, as well as up and down.

In practice, a TLR-2®model on a handgun can be adjusted to keep the bullet strike within about 2” high

and 2” low out to about 100 feet. There are two adjustment screws mounted in brass bushings located on

the laser cartridge housing (for the TLR-2®G on the side body and housing). The windage adjustment is

located on the left hand side of the laser cartridge. Turn the set screw clockwise to move the laser to the

left (POI right). Turn the set screw counter-clockwise to move the laser to the right (POI left). The elevation

Constant

OFF (PADDLE)

Constant

Momentary

OFF (PADDLE)

Momentary

(TLR-2®MODE SWITCH)

Laser Laser/LEDLED

Straight or Coiled

Cord Available

adjustment is located on the underside of the TLR-2®model laser cartridge. With the TLR-2®model

pointed down range a clockwise turn of the adjustment screw will move the laser down (POI up).

A counter-clockwise turn on the adjustment screw will move the laser up (POI down). Move the laser dot in

the direction that the shots are hitting the target (example: If the bullets are striking low and right, move

the laser dot down and right to coincide with the bullet strike).

NOTE: When making large adjustments there may be an interaction that causes the laser to move diago-

nally or bind. It may become necessary to rotate the opposing adjustment screw counterclockwise to allow

the laser cartridge to move to the desired position.

Accessories

TLR Remote Switch

(TLR-1 HPL®shown)

TLR Contour Remote Switch

(TLR-1®Shown)

(Contour remote not recommended for use with the TLR-2 HL®G)

Maintenance

The TLR rail clamp tensioning bolt requires an application of high quality gun oil to keep it rust free. Use a soft

cloth and mild detergent to clean the glass LED lens and keep it free of dirt and grime. The laser aperture on

the TLR-2®models can be cleaned with a Q-tip (or similar item) and mild detergent.

NOTE: Always avoid aggressive cleaning solutions as they may damage the TLR.

Streamlight Limited Lifetime Warranty:

Streamlight warrants this product to be free of defects for a lifetime of use except for batteries and

bulbs, abuse and normal wear. We will repair, replace or refund the purchase price of this product should

we determine it to be defective. This limited lifetime warranty also excludes rechargeable batteries,

chargers, switches and electronics which have a 2 year warranty with proof of purchase. THIS IS THE

ONLY WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARE

EXPRESSLY DISCLAIMED EXCEPT WHERE SUCH LIMITATION IS PROHIBITED BY LAW. You may have

other specic legal rights which vary by jurisdiction.

Go to www.streamlight.com/support for a complete copy of the warranty, and information on product

registration and the location of authorized service centers. Retain your receipt for proof of purchase.

Service

The TLR contains few or no user-serviceable parts.

Go to www.streamlight.com for the location of an authorized Streamlight repair center near you.

For expedited service, go to www.streamlight.com/support/service and complete

the Online Service Request.

Or contact:

Customer Service

STREAMLIGHT, INC.

30 Eagleville Road

Suite 100

Eagleville, PA 19403-3996

Phone: (800) 523-7488 Toll-Free / +1 (610) 631-0600

Fax: (800) 220-7007 / +1 (610) 631-0712

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere StreamLight Taschenlampe Handbücher

StreamLight

StreamLight TASK-LIGHT 3AA Bedienungsanleitung

StreamLight

StreamLight PROPOLYMER 2AA Bedienungsanleitung

StreamLight

StreamLight Stinger 75014 Bedienungsanleitung

StreamLight

StreamLight PROTAC HL 5-X USB Bedienungsanleitung

StreamLight

StreamLight tLR-1 Series Bedienungsanleitung

StreamLight

StreamLight Stinger Bedienungsanleitung

StreamLight

StreamLight Super Tac series Bedienungsanleitung

StreamLight

StreamLight Stinger LED Series Bedienungsanleitung

StreamLight

StreamLight ProPolymer 2AA LED Bedienungsanleitung

StreamLight

StreamLight Stinger LED HP Bedienungsanleitung

StreamLight

StreamLight strion Bedienungsanleitung

StreamLight

StreamLight STINGER 2020 Bedienungsanleitung

StreamLight

StreamLight VANTAGE Bedienungsanleitung

StreamLight

StreamLight Protac 1L Bedienungsanleitung

StreamLight

StreamLight Stinger LED Series Bedienungsanleitung

StreamLight

StreamLight TLR-6 Bedienungsanleitung

StreamLight

StreamLight strion Bedienungsanleitung

StreamLight

StreamLight PROPOLYMAX 4AA Bedienungsanleitung

StreamLight

StreamLight PROTAC HL USB Bedienungsanleitung

StreamLight

StreamLight Scorpion Bedienungsanleitung

StreamLight

StreamLight DUALIE 2AA Bedienungsanleitung

StreamLight

StreamLight DUALIE 3AA Bedienungsanleitung

StreamLight

StreamLight Stylus Pro Reach Bedienungsanleitung

StreamLight

StreamLight DUALIE 3AA Bedienungsanleitung

Beliebte Taschenlampe Handbücher anderer Marken

Silverline

Silverline 994024 Bedienungsanleitung

Gama Sonic

Gama Sonic 23i60065 Bedienungsanleitung

Ryobi

Ryobi RFL180M Bedienungsanleitung

RIB

RIB SPARK ACG7061 Bedienungsanleitung

Abicor Binzel

Abicor Binzel MB EVO PRO Series Bedienungsanleitung

PELI

PELI 7610 Bedienungsanleitung

Black & Decker

Black & Decker FSL18 Bedienungsanleitung

Black & Decker

Black & Decker 9506 Bedienungsanleitung

Berner

Berner 341709 Bedienungsanleitung

PELI

PELI 3415 Zone 0 Bedienungsanleitung

ADC

ADC Adlite Pro Wartungshandbuch

Fervi

Fervi 0338 Bedienungsanleitung

Milwaukee

Milwaukee M18 IL Bedienungsanleitung

Spectronics

Spectronics Spectroline LeakTracker SPI-LT Bedienungsanleitung

Larson Electronics

Larson Electronics SLEDB-110V-M Bedienungsanleitung

vulta

vulta hurricane 262 lumen fg-e15 Bedienungsanleitung

FALCON EYE

FALCON EYE FBR0112 Bedienungsanleitung

Heider

Heider CFX Super Power Bedienungsanleitung