Structural Concepts Addenda SHS9251 Montageanleitung

Rev A Date: 9.10.2019

Operating Manuals\Addenda SHS9251 Ambient Bread Island Lineup 21-12070.pub

Structural Concepts Corporation ∙ 888 E. Porter Road ∙ Muskegon, MI 49441

Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts.com

READ AND SAVE THESE INSTRUCTIONS

P/N 21-12070

INSTALLATION &

OPERATING MANUAL

Model SHS9251 7’-8” Ambient Bread Island Display:

> Adjustable/Lockable Casters > LED Lighting At Underside Of Certain Shelves

> Shelving Adjustable At 5° and 10° Angles > Transparent Product Stops > Rubberized Bumpers

> Reversible Bread Display With Acrylic Dividers > Stowaway Shelf With Acrylic Dividers

View of Case

With Stowaway

Shelf Lowered

View of Case With

Stowaway Shelf

Raised And Locked

TABLE OF CONTENTS

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING …………..………….

INSTALLATION: TOOLS REQUIRED / PALLET DISCONNECT …..…………………………………………..

INSTALLATION, CONT’D: CASTER MANEUVERABILITY & ADJUSTABILITY …………………………..

INSTALLATION, CONT’D: CASE REMOVAL FROM PALLET / LOCKING CASTERS ………………

MODEL SHS9251 LAYOUT: GENERAL SHELVING (15º VS. 0º ANGLES) ……………………………

MODEL SHS9251 LAYOUT, CONT’D: STOWAWAY SHELF / REVERSIBLE SHELF / PRODUCT

STOPS …………………………………………………………………………………………………..

MODEL SHS9251 LAYOUT, CONT’D: LED LIGHTS & SWITCHES / STOWAWAY SHELF

SIGNAGE SURFACE ………………………………………………………………………………….

MODEL SHS9251 LAYOUT, CONT’D: LED STYLE LIGHT FIXTURES ………………………………...

MODEL SHS9251 LAYOUT, CONT’D: WIRE ROUTE …………………………………………………….

MODEL SHS9251 LAYOUT, CONT’D: FIELD ACCESS BOX / LED DRIVER …………………………

GENERAL CLEANING ……………………………………………………………………………….………..

STAINLESS STEEL CLEANING ……………………………………………………………………....……..

TROUBLESHOOTING ………………………………………………………………………………………….

SERIAL LABEL INFORMATION & LOCATION ..……………………………………...…....………….…..

TECHNICAL SERVICE CONTACT INFORMATION & WARRANTY INFORMATION ……….………..

OVERVIEW

 These Structural Concepts display cases are

designed to merchandise packaged products at

ambient temperatures.

 Refrigerator unit has its own operating manual.

 Cases should be installed and maintained according

to this operating manual’s instructions to ensure

proper performance. Improper use will void warranty.

COMPLIANCE

 Performance issues when in violation of applicable

NEC, federal, state and local electrical codes are not

covered by warranty. See below.

OVERVIEW / COMPLIANCE / PRECAUTIONS / WARNINGS / WIRING DIAGRAM

WARNING

Risk of electric shock. Disconnect power before servicing unit.

CAUTION! More than one source of electrical supply is

employed with units that have separate circuits.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

ELECTRICAL

HAZARD

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local

electrical codes.

CAUTION! LED LAMP REPLACEMENT GUIDELINES

LED lamps reflect specific size, shape and overall design.

Any replacements must meet factory specifications.

CAUTION

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

you MUST use a GFCI breaker in lieu of a GFCI receptacle.

ATTENTION

CONTRACTORS

PRECAUTIONS AND WARNINGS

 This page contains an important precautions and

warning to prevent injury or death.

 Please read carefully!

WIRING DIAGRAM

 Each case has its own wiring diagram folded and in its

own packet.

 Wiring diagram placement may vary; it may be placed

near ballast box, field wiring box, raceway cover, or

other related location.

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

WIRING DIAGRAM FORMAT & LOCATION

 Each case has its own wiring diagram folded & in its own packet.

 Wiring diagram placement may vary; it may be placed near field

wiring box, raceway, or other related location.

INSTALLATION: TOOLS REQUIRED / PALLET DISCONNECT

Note: This Page Only Applies To Models With

Lockable/Adjustable Features.

1. Tools Required For Installation Process

 Driver with Phillips® head bit.

2. Disconnect Case From Pallet

 Use driver with Phillips® head bit to remove all

shipping components that are used to secure case to

pallet. Discard/recycle.

 Place J-bar/pry bar under base frame. Raise case up

from pallet to take weight off casters.

 With case raised, lower casters all the way down

against pallet (see next step for instructions on

lowering or raising casters).

 Remove rubber shipping blocks (if any).

Caster

Vertical

Adjustment

Ring

Caster

INSTALLATION, CONT’D: CASTER MANEUVERABILITY & ADJUSTABILITY

Note: This Page Only Applies To Models With

Lockable/Adjustable Features.

3. Caster Height: Raising and Lowering

 Raise or lower casters (to adjust case height) by

rotating casters’ vertical adjustment rings.

 Rotate vertical adjustment ring clockwise to lower

caster (and increase height of case).

 Rotate vertical adjustment ring counter-clockwise

to raise caster (and decrease height of case).

4. Caster Rolling Capability: Unlocking

 Important! Case is shipped with caster mechanisms

that are factory set at ON (locked) which prevents

case from rolling.

 Unlock casters by pressing OFF on the caster

mechanism. See illustration at right.

5. Carefully Roll Case Down Pallet

 Check that casters are lowered as far down as

they will go (as instructed on previous step).

 Slide case to rear of pallet (see below illustration).

 Caution! 2 people may be required

for this task!

 Carefully lower to floor

(using ramp if available).

 Slide pallet from under

case as required.

 Maintain support of case

at all times while rolling

down ramp.

 See illustration at right.

Press “OFF” Lever To

Unlock Caster (And

Allow Casters To Roll)

Pallet

Support case

while removing

from pallet

Ramp

Caster

Tighten Set

Screws To

Lock Caster

Height In

Place

INSTALLATION, CONT’D: LOCKING CASTERS / TOE-KICK ATTACHMENT

6. Casters: Locking

 After case is at desired position (and height),

use level to check that case is level and plumb.

 Readjust height as needed (as instructed on

previous page).

 Locking Height: After proper height (and positioning) of

case is attained, tighten the two (2) set screws to lock

each caster’s height in place.

 Locking Movement: Then, to prevent casters’ rolling

capability, lock casters by pressing ON atop the “ON”

and “OFF” lever mechanism (shown at right).

 Case will now be secured at its new location.

7. Toe-Kick Attachment

 Toe-kicks are held in place with magnets suspended at

all four corners of the case.

 After case has been moved into position and locked in

place, all four (4) toe-kicks must be attached.

 See illustration below.

Press “ON” Lever To

Lock Caster In Place

(And Prevent Caster

From Rolling)

Rear Toe-Kick

Front Toe-Kick

Left Toe-Kick

Right

Toe-Kick

MODEL SHS9251 LAYOUT: GENERAL SHELVING (15º VS. 0º ANGLES)

Model SHS9251 Layout

 Shelves are single piece construction; they are

adjustable and/or removable.

 To remove, simply lift upward. Move to new

position or remove from case for cleaning or

storage.

 Pins may be staggered to allow angled shelving

(as illustrated in lower shelves, below).

 Use pliers to remove shelf support pins and

adjust as desired.

 Wicker support bracket have rubber feet.

 Casters are adjustable and lockable

0º (Flat) Shelving

Notch

15º Shelving Notch

Shelving Retaining

Clip (Typ.)

Case Rear

MODEL SHS9251 LAYOUT: STOWAWAY SHELF / REVERSIBLE SHELF / PRODUCT STOPS

Model SHS9251 Layout - Stowaway Shelf, Etc.

>> Model SHS9251 has a stowaway shelf that must

be raised and locked in place with a lever (lever is

shown in top-right illustration).

>> Model SHS9251 also has a reversible shelf with

an adjustable product stop.

1. When stowaway shelf is lowered, product stops

must be in RAISED POSITION (see below

insertion slots and product stop placement).

2. Stowaway shelf may be raised for

placing flyers and ads on surface.

When stowaway shelf is raised,

reversible shelf must be

repositioned and product stops

must be in LOWERED

POSITION (as shown

below).

Product

Stop

Product

Stop

Product Stop

Hook (Typ.)

Reversible

Shelf

Slots For

Product Stop

Hooks (Typ.)

Product Stop

Hook (Typ.)

Lever

Stowaway

Shelf

Lowered

Stowaway

Shelf Raised

And Locked

Product Stops

Reversible

Shelf

Slots (Typ.)

Reversible

Shelf

MODEL SHS9251 LAYOUT: LED LIGHTS & SWITCHES / STOWAWAY SHELF SIGNAGE SURFACE

Model SHS9251 Layout - LED Lights & Switches

A. LED lights are on all four (4) sides of case

(as illustrated below).

B. The main LED light switch controls ALL LED

lights except the ONE above the Stowaway

Shelf.

C. The light switch on the Stowaway Shelf side

controls ONLY the LED light positioned above it.

This LED light may be used when shelf is either

raised or lowered.

Model SHS9251 Layout - Stowaway Shelf / Surface

A. When the Stowaway shelf is raised, it is to be

locked in place with latch (shown at right).

B. The surface created when Stowaway Shelf is

RAISED may be used for signage.

LED Light Switch For

Stowaway Shelf Side

LED Light For

Stowaway Shelf Side

Shelving LED Lights

(Stowaway Shelf Side)

Shelving LED Lights

(Center Shelving) Typ.

Shelving LED Lights (Opposite

Stowaway Shelf Side)

Main LED Light

Switch For ALL

Case Lights

EXCEPT The

Light Above

Stowaway

Shelf

After Stowaway Shelf

Is Raised and Locked,

Signage May Be

Placed On Surface

Latch To Lock

Stowaway Shelf In

Upright Position

MODEL SHS9251 LAYOUT: LED STYLE LIGHT FIXTURES

LED Style Light Fixtures

Removal of Faulty LED Lights:

 LED lights rarely require change-out.

 Contact Structural Concepts’ Technical Service

Department for replacement LED lights.

 Turn off LED light switch.

 To remove faulty LED light, follow these steps:

A. Disconnect plug from LED light.

B. Using both hands, grasp LED light assembly

(with its magnetic mounting clips). Pull

downward and off its shelf (or header).

C. Remove magnetic mounting clips from LED

light by pressing against flange part of clip

with thumb.

>> Note: Mounting clips MAY be riveted to shelf or

header. In such instances, simply remove LED light

from mounting clips by pressing against flange part

of clips with thumb.

Replacement of LED lights:

 Attach magnetic mounting clips onto LED light.

 Adjust magnetic mounting clips so they are equally

spaced on LED light.

 Reattach LED light assembly to its shelf/header.

 Position properly in shelf/header.

>> Note: If mounting clips are riveted to shelf (or

header), attach by placing LED in base of clip and

then snapping into clip at FLANGE SIDE.

 Press plug’s barrel-shaped insert all the way into

LED light.

 Important: If plug is not inserted ALL THE WAY IN

the LED light’s orifice, the light may not energize.

See “BAD” vs. “GOOD” insertion illustrations

below-right.

 Turn LED light switch back on.

Magnetic Mounting

Clip View #2

LED

Lights

Plug

Barrel

Shaped

Insert

LED

Light

Magnetic Mounting

Clip View #1 No Gap

Gap

Light

Fixtures

(Typ.)

Inhaltsverzeichnis

Andere Structural Concepts Vitrine Handbücher

Structural Concepts

Structural Concepts ENCORE Series Bedienungsanleitung

Structural Concepts

Structural Concepts Harmony HMG2642R.4439 Montageanleitung

Structural Concepts

Structural Concepts Oasis HEFSC663R Bedienungsanleitung

Structural Concepts

Structural Concepts GP641RRLB Bedienungsanleitung

Structural Concepts

Structural Concepts BLEND NM4855RSSV Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis P63941R Bedienungsanleitung

Structural Concepts

Structural Concepts Harmony HMG2642R.4439 Bedienungsanleitung

Structural Concepts

Structural Concepts HECO37R Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Montageanleitung

Structural Concepts

Structural Concepts Oasis W3R Bedienungsanleitung

Structural Concepts

Structural Concepts GP441RG.6122 Bedienungsanleitung

Beliebte Vitrine Handbücher anderer Marken

Hatco

Hatco FLAV-R-SAVOR FSCD Series Bedienungsanleitung

Bonnet Neve

Bonnet Neve SKYLIGHT Bedienungsanleitung

True

True TCGD-50 Bedienungsanleitung

Tecnodom

Tecnodom EVO SELF Betriebsanleitung

Delfield

Delfield F15SC48N Bedienungsanleitung

saro

saro FIONA Bedienungsanleitung

Hendi

Hendi 233962 Bedienungsanleitung

Hoshizaki

Hoshizaki HNC-120BE-L-BLH Bedienungsanleitung

Nordcap

Nordcap GENIUS 2 H145-L70 Bedienungsanleitung

Omcan

Omcan RS-CN-0140-D Bedienungsanleitung

Tecnodom

Tecnodom M Series Betriebsanleitung

freor

freor MERCURY Bedienungsanleitung

Costan

Costan WHALE 2000 G LG300 Bedienungsanleitung

Costan

Costan IMPALA Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TCGD-50 Bedienungsanleitung

Bartscher

Bartscher 100L Bedienungsanleitung

Steelcase

Steelcase Opus Bedienungsanleitung

Hatco

Hatco Glo-Ray GRHD-2P Anwendungshandbuch