Stryker 240-099-155 Bedienungsanleitung

Unpacking and Installation Instructions / Instructions de déballage et d’installation /

Instrucciones de desembalaje e instalación / 开箱和安装说明 / 포장 풀기 및 설치 지침 /

Hướng dẫn mở bao bì và lắp đặt

P41610 Rev. C

2020-01 EN / FR / ES / ZH / KO / VI

240-099-155 / 240-099-156

Connected OR Cart / Chariot Connected OR /

Carro Connected OR / Connected OR 流动车 /

Connected OR 카트 / Xe đẩy Connected OR

P41610 Rev. C EN 1

Contents

Unpacking the Connected OR Cart..........................................................................................2

Inspecting the Cart....................................................................................................................4

Installing the Shelves................................................................................................................5

Installing the Connected OR Mount.........................................................................................6

Installing the Monitor on the Connected OR Mount...............................................................8

Installing the Footswitch Holder (Optional Accessory).......................................................10

Final Inspection .......................................................................................................................10

P41610 Rev. C2 EN

Unpacking the Connected OR Cart

To unpack the Connected OR Cart:

1. Remove the top cap and outer tube pieces of the carton.

2. Remove the ramp from the side of the cart.

3. Remove the polybag.

4. Cut the banding that secures the cart to the pallet.

5. Place the ramp on the ground at the rear of the cart.

P41610 Rev. C EN 3

6. Unlock all four wheels using the foot levers.

7. Place one foot on the center of the leading edge of the ramp to secure it against the pallet.

Caution: Ensure that the ramp is ush against the pallet before rolling the cart o󰀨.

8. Carefully roll the cart o󰀨 the pallet and down the ramp by grasping the handles and pulling it towards you.

P41610 Rev. C4 EN

9. Remove the shrink wrap from around the cart.

10. Remove the boxes containing the shelves and Connected OR Mount.

Inspecting the Cart

After unpacking, inspect the Connected OR Cart and following components for damage that may have occurred

during shipping:

• SPY-PHI imager holder and cable hook

• Transporting and positioning handles

• Accessory basket

• IFU holder

• Monitor stow bracket

• CO2tank holder

• Rear door

• Power cord hooks

P41610 Rev. C EN 5

• Cart cabinet

• Labels

• Connected OR Mount monitor arm

• Console power cables

• Shelves

• Wheels and brakes

• Power cord

• Cart power button

Note: For diagrams showing the locations of accessories, see the Connected OR Cart Instructions for Use,

pages 2 to 4.

Installing the Shelves

To install the shelves:

1. Remove each shelf from its box and inspect it for damage that may have occurred during shipping.

2. Install each shelf in the desired location in the cabinet according to the following illustrations.

Caution: Ensure that each shelf is installed with the top side facing up.

P41610 Rev. C6 EN

Installing the Connected OR Mount

To install the Connected OR Mount:

1. Remove the arm from the box and inspect it for any damage that may have occurred during shipping.

2. On the end of the radial arm (mounted on the cart), loosen the lock screw (lower screw) using a 4 mm hex

tool but do not remove it.

P41610 Rev. C EN 7

3. Insert the post of the arm in the socket at the end of the radial arm.

4. Tighten the lock screw.

5. Attach the monitor mounting bracket to the tilt mechanism on the end of the arm using the 4 at-head screws

provided with the arm (#10-32 x 0.375”) and a Philips screwdriver.

Ensure that all four screws are fully seated against the monitor stow bracket and that the screw heads are not

protruding.

P41610 Rev. C8 EN

Installing the Monitor on the Connected OR Mount

Install the monitor in two steps. First, install the monitor power supply in the base of the Connected OR Cart. Then

install the monitor on the Connected OR Mount (arm).

To install the monitor power supply:

1. Remove the bottom shelf by removing the 4 screws shown below.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Stryker Medizinische Geräte Handbücher

Stryker

Stryker TPS MicroDrill 5100-15 Bedienungsanleitung

Stryker

Stryker TPS 5100-9 Bedienungsanleitung

Stryker

Stryker 3002 Bedienungsanleitung

Stryker

Stryker Trauma Stretcher 1037 Bedienungsanleitung

Stryker

Stryker 1089 Bedienungsanleitung

Stryker

Stryker 1020 Bedienungsanleitung

Stryker

Stryker Zoom 2040 Bedienungsanleitung

Stryker

Stryker MX-PRO 6083 Bedienungsanleitung

Stryker

Stryker SERFAS Bedienungsanleitung

Stryker

Stryker sdc classic Bedienungsanleitung

Stryker

Stryker The Go BED FL17E Bedienungsanleitung

Stryker

Stryker Prime Series Bedienungsanleitung

Stryker

Stryker LD304 Bedienungsanleitung

Stryker

Stryker POWEReam 4405 Series Bedienungsanleitung

Stryker

Stryker IsoTour Standard 2872 Bedienungsanleitung

Stryker

Stryker System 6 6208 Bedienungsanleitung

Stryker

Stryker C-Mount Bedienungsanleitung

Stryker

Stryker MX-PRO R3 Bedienungsanleitung

Stryker

Stryker 6100 Rugged M1 Handbuch

Stryker

Stryker Neptune 2 Bedienungsanleitung

Stryker

Stryker Flosteady Arthroscopy Pump 200 Bedienungsanleitung

Stryker

Stryker 747 Bedienungsanleitung

Stryker

Stryker IsoAir Bedienungsanleitung

Stryker

Stryker Core 5400-050-000 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung

Romet

Romet R210 Bedienungsanleitung