STYLE EL-DRL Kurzanleitung zur Einrichtung

Electric height adjustable desk

ASSEMBLY &

USE INSTRUCTIONS

CAUTION/INFORMATION

Make sure no obstacles are in the desk's path.

Make sure the desktop is not touching any walls.

Make sure all cords are appropriate length to

accommodate the change in height.

WARNING

PINCH POINT

keep hands and

fingers clear.

Keep children away from electric height-adjustable desks,

control units and handsets. There is a risk of injury and electric shock.

Keep all electrical components away from liquids.

Do not set or stand on the desk Frame.

Do not crawl or lie under the desk Frame.

Do not place any objects taller than 50 underneath the desk.cm

This product is designed with a duty cycle of 10% (2 min. on, 18 min. off)

In the event of a power outage or if the power cord is unplugged,

a manual reset may be necessary - see Step 12.

USE/LIABILITY

This height adjustable desk has electric motors and is designed for use in dry work areas only. The

desk height is adjustable so that it can be positioned at the most ergonomically suitable height.

Any other use is at user's risk.

Under no circumstances does the manufacturer accept warranty claims or liability claims for damages

caused from improper use or handling of the desk frame.

IMPORTANT:

Please read this manual carefully.

If this desk is sold ,please provide this manual to the buyer.

Do not open any of the components - the Legs, control Box, or handset.

There is a danger of electric shock.

Page1

PARTS

TOOLS REQUIRED

COMPONENTS

HARDWARE

4MM Allen Wrench

(included)

Phillips Head Screwdriver

and/or Power Drill

Tape measure

Page2

Foot with

Glides Crossbar End Center Rail Side Bracket

Legs

x3 x3 x4 x4 x3

Control Box Programmable

Handset

Power cord

Cables:60cm

x1 x1 x3 x1

Machine Screws:

M6x12

x40

Cable Clips

Machine Screws:

M6x10

x16 x10

Wood Screws:

ST M5x16

x17

Part

1Crossbar End

2Leg

3Foot

4Crossbar Center Rail

5Side Bracket

6Control Box

7Programmable Handset

8Power Cord

9Cables

11Machine Screws:M6x12

12Machine Screws:M6x10

13Wood Screws:ST M5x16

14Cable Clips

Foot Glides

Page3

PARTS

QTY

13 14

ASSEMBLY INSTRUCTIONS

Page4

Lay out all components and hardware to ensure that you have all components and hardware listed on the

parts page.

Fully separate the Crossbar Ends (Part #1). You will find the Crossbar Center Rails (Part #4) inside.

STEP1

Place one of the Legs (Part #2) into the Crossbar End (Part #1)

Line up the holes on each Leg (Part #2) with the holes on each

Crossbar End (Part #1)

Using the supplied Allen Wrench, insert four (4) M6x12 Machine

Screws (Part #11) through the holes in each Crossbar End (Part #1) going

into the Leg (Part #2) and rotate each screw just a few turns.

You will need to dip the assembly over to gain access to all four (4) M6x12

Machine Screws (Part #11).

STEP2

ASSEMBLY INSTRUCTIONS

Page5

STEP3

Position one of the Crossbar Ends (Part #1) on its side.

Tighten the screws(Part #16) from the top.

If you drop a screw inside the Crossbar End (Part #1), simply tilt

to retrieve the screw.

Using the Allen Wrench, rotate each screw just a few turns.

Repeat Step 4 with the other assembly.

If you are having difficulty inserting any of the

screws from Step 3 or 4, it is because some of

the installed screws are too tight.

Slide the two (2) Crossbar center Rails (Part #4)

into the two Crossbar Ends, (Part #1)

ensuring:

a) the slots Face inward

b) the slot is closer to top edge of the

Crossbar center Rail (Part #4) when

the assembly is upside down (see inset)

STEP4

ASSEMBLY INSTRUCTIONS

Page6

STEP4

STEP5

Lock the position of the Crossbar center Rails (Part #4)

using eight (8) M6x10 Machine Screws (Part #12).

Remember,maximum width is 180cm.

Using the M6*10 Machine Screw(part 12) to fix the 3rd central frame.

ASSEMBLY INSTRUCTIONS

Page7

STEP6

STEP7

For each leg, attach a foot (Part #3) with

four (4) M6x12 Machine Screws (Part #11)

and tighten screws in a cross pattern.

Lock the position of the Crossbar center Rails (Part #4)

using eight (8) M6x10 Machine Screws (Part #12).

Remember,maximum width is 180cm.

ASSEMBLY INSTRUCTIONS

TROUBLESHOOTING

TECHNICAL SPECIFICATIONS

Plug the Power Cord into a 240v outlet.

Make sure no obstacles are in the desk's path.

Make sure the desktop is not touching any walls.

Make sure all cords are appropriate length to accommodate the change in height

IMPORTANT: You must RESET the desk prior to use.

Height Range

Base width

Travel Speed

Weight capacity

Duty Cycle

60CM-125CM(without desktop)

110CM-180CM

38 per second(no load)

1 0kg8

10%. Max. 2 mins on, 18 mins off

Soft start/stop

Adjustable leveling studs

4 Memory presets

STEP8

Page8

IF your desk is not functioning properly it may need to be reset. Unplug the power cord for 20 seconds.

Plug the power cord back in and follow the RESET procedure outlined in step 8.

IF the LED readout displays “Er8" or "Er9" or "Er00"confirm that all wired connections are secure

(legs to cables, cables to control box). Then perform the reset procedure outlined in step 8.

IF the error message persists after the reset procedure, contact your seller.

IF the height between the legs exceeds 4cm, perform the reset procedure outlined in step 8.

IF the handset displays “HOT”，let the base cool down for 20 minutes.

RESET PROCEDURE: Push and hold the DOWN button on the Programmable Handset (Part #7) the

LED reads “RST”

until the desk reaches its lowest height, slightly rises and stops. Release the DOWN button.

Your desk is now ready to use.

To program up to four presets: Use the up/down buttons to find a desired height, then press "S"(or “M”)

followed by a number 1 - 4.

CAUTION: Once a preset button is pushed, the desk will move to the programmed height .

USE INSTRUCTIONS

Up & Down Movement:

Press the UP arrow continuously, the legs will move up

 Press the DOWN arrow continuously, the legs will move down

 Release arrows to stop movement.

Memory Preset Positions:

 Use the UP and DOWN arrows to set table at a desired height.

 Press the POSITION SETTING BUTTON (S) followed by one of the 4 PRESET POSITION

BUTTONS(1 2 3 4) buttons. The memory position is set.

 There are up to 4 presets available. To return to a memory preset press the desired number.

Warning:

 It is recommended that the legs not be moved up and down continuously for more than 2

minutes within a 20 minute interval or exceed the lift capacity.

 To avoid over loading the transformer an overload protection program is built into the system.

If the unit stops working let it cool off before trying to raise or lower it again.

 If the unit overloads the LED display will display "HOT".

Reset:

 Press the DOWN button and lower the desk to its lowest setting..

 Press the DOWN Button again for ~ 5 seconds until the LED reads “RST”

 Press the DOWN button & hold it while the legs move up & down to level and stop.

 Release the DOWN button as the reset is now complete and your table is ready to use.

Error Code Key:

E02 –unbalanced, keep the desk moving will auto matically adjust it to balance state.

E04 –overload,move something off the desk to reduce the loading weight.

E05 – resistance to return.

R5T - means “reset” cycle in progress.

Er8 – miscommunication between control box and legs plugged into port 1.

Er9– miscommunication between control box and legs plugged into port 2.

HOT –desk has reached its duty cycle limit – let desk base cool for 20 minutes.



Page9

Inhaltsverzeichnis

Andere STYLE Inneneinrichtung Handbücher

STYLE

STYLE PALMETTO D71 M20302 Bedienungsanleitung

STYLE

STYLE Uplifting Omesh-L Kurzanleitung

STYLE

STYLE ERGO-1 Bedienungsanleitung

STYLE

STYLE Uplifting ATLAS Bedienungsanleitung

STYLE

STYLE ZODIAC Bedienungsanleitung

STYLE

STYLE SS 30IN ANTIQUE WHT VANITYW/MIRR Bedienungsanleitung

STYLE

STYLE ergo mesh Bedienungsanleitung

STYLE

STYLE OMesh-L Bedienungsanleitung

STYLE

STYLE BRYANT 5PCS DINING SET Bedienungsanleitung

STYLE

STYLE D71 M25783 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

Furinno

Furinno 18089 Bedienungsanleitung

Munchkin

Munchkin Push to Close MK0001 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Anthro

Anthro GT03 Series Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung