Sub-Zero BI-30UA/S/PH-RH Bedienungsanleitung
CLASSIC REFRIGERATION
INSTALLATION GUIDE
SPECIFICATIONS, INSTALLATION, AND MORE
2 | Sub-Zero Customer Care 800.222.7820
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
CLASSIC REFRIGERATION
Contents
3Classic Refrigeration
4Opening Dimensions
8Dual Installation
8Electrical
9Plumbing
9Preparation
10 Anti-Tip Bracket
12 Placement
12 Water Line
13 Custom Panels
16 Alignment
17 Completion
Features and specications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
subzero.com | 3
Product Information
Important product information, including the model and
serial number, are listed on the product rating plate. The
rating plate is located at the top frame of the unit, inside the
door. Refer to the illustration below.
If service is necessary, contact Sub-Zero Factory Certied
Service with the model and serial number. For the name
of the nearest Sub-Zero Factory Certied Service or for
questions regarding the installation, visit the Support
and Service section of our website, subzero.com, or call
Sub-Zero Customer Care at 800-222-7820.
Tools and Materials
•Screwdrivers—standard and Phillips.
•Power drill.
•Drill bits (masonry bits required for concrete installation).
•Torx drives—T-10, 15, and 20.
•Standard Allen wrench set.
•Standard socket and wrench set.
•2' and 4' levels.
•Tubing cutter.
•3' of 1/4" OD copper, braided stainless steel, or PEX
tubing.
•Saddle valve.
•Material to protect home, ooring, and cabinetry during
installation.
Rating plate location
RATING
PLATE
CLASSIC REFRIGERATION
4 | Sub-Zero Customer Care 800.222.7820
SITE PREPARATION
Opening Dimensions
STANDARD INSTALLATION
3/4"(19)
TYPICAL
FRAMED
CABINETRY
W
FILLER
31/2"(89)
FINISHED
RETURN
FRAMELESS
CABINETRY
W
3/4"(19)
TYPICAL
31/2"(89)
FINISHED
RETURN
NOTE:
31/2"(89) finished returns will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit
.
833/4"
(2127)
OPENING
HEIGHT
24" (610)
OPENING
DEPTH
FRONT VIEW
SIDE
VIEW
TOP VIEW
W
OPENING WIDTH
If two units are installed side by side, refer to page 6.
OPENING WIDTH W
30" Model 291/2"(749)
36" Model 351/2"(902)
42" Model 411/2"(1054)
48" Model 471/2"(1206)
subzero.com | 5
Opening Dimensions
FLUSH INSET INSTALLATION
Dimensions assume a 3/4" (19) panel thickness. If two units
are installed side by side, refer to page 7.
84"
(2134)
FLUSH
INSET
HEIGHT
1/4"
(6)
263/16"
(665)
FLUSH
INSET
DEPTH
23/16"
(56)
NOTE:
31/2"(89) finished returns and shaded areas will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit with
3/4"(19) panel.
FRONT VIEW
SIDE
VIEW
TOP VIEW
11/4"
(32)
W
FLUSH INSET WIDTH
FINISHED
CLEATS
511/16"
(145)
FINISHED
RETURN
FILLER
FRAMED
CABINETRY
W
CLEAT
3/4"(19)
TYPICAL
31/2"
(89)
511/16"
(145)
FINISHED
RETURN
FRAMELESS
CABINETRY
W
31/2"
(89)
CLEAT
3/4"(19)
TYPICAL
SITE PREPARATION
FLUSH INSET WIDTH W
30" Model 32" (813)
36" Model 38" (965)
42" Model 44" (1118)
48" Model 50" (1270)
6 | Sub-Zero Customer Care 800.222.7820
Opening Dimensions
DUAL STANDARD INSTALLATION
NOTE:
31/2"(89) finished returns will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit
.
833/4"
(2127)
OPENING
HEIGHT
24" (610)
OPENING
DEPTH
FRONT VIEW
SIDE
VIEW
TOP VIEW
W
OPENING WIDTH
3/4"(19)
TYPICAL
FRAMED
CABINETRY
W
FILLER
31/2"(89)
FINISHED
RETURN
FRAMELESS
CABINETRY
W
3/4"(19)
TYPICAL
31/2"(89)
FINISHED
RETURN
A dual installation kit is required for this installation.
SITE PREPARATION
DUAL OPENING WIDTH W
Two 30" Models 593/4" (1518)
30" and 36" Models 653/4"(1670)
Two 36" Models 713/4"(1822)
subzero.com | 7
Opening Dimensions
DUAL FLUSH INSET INSTALLATION
84"
(2134)
FLUSH
INSET
HEIGHT
1/4"
(6)
263/16"
(665)
FLUSH
INSET
DEPTH
23/16"
(56)
FRONT VIEW
SIDE
VIEW
TOP VIEW
FINISHED
CLEATS
11/4"
(32)
W
FLUSH INSET WIDTH
NOTE:
31/2"(89) finished returns and shaded areas will be visible and should be finished to match cabinetry.
Shaded line represents profile of unit with
3/4"(19) panel.
511/16"
(145)
FINISHED
RETURN
FILLER
FRAMED
CABINETRY
W
CLEAT
3/4"(19)
TYPICAL
31/2"
(89)
511/16"
(145)
FINISHED
RETURN
FRAMELESS
CABINETRY
W
31/2"
(89)
CLEAT
3/4"(19)
TYPICAL
Dimensions assume a 3/4"(19) panel thickness. A dual instal-
lation kit is required for this installation.
SITE PREPARATION
DUAL FLUSH INSET WIDTH W
Two 30" Models 621/4"(1581)
30" and 36" Models 681/4"(1734)
Two 36" Models 741/4"(1886)
8 | Sub-Zero Customer Care 800.222.7820
SITE PREPARATION
Electrical Requirements
Installation must comply with all applicable electrical codes.
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit ser-
vicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause inter-
ruption of operation.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp dedicated circuit
Receptacle 3-prong grounding-type
CAUTION
The outlet must be checked by a qualied electrician
to be sure it is wired with the correct polarity. Verify the
outlet is properly grounded.
WARNING
Do not use an extension cord, two-prong adapter, or
remove the power cord ground prong.
751/2" (1918)
FROM FLOOR
7"
(178) E
6"
(152)
RIGHT SIDE
OF OPENING
Electrical supply location
Dual Installation
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom ller strip
require a dual installation kit. If a dual installation kit is not
specied, a 2" (51) ller strip is recommended between units.
Dual installations without a ller strip can only be accom-
plished using two units with opposite hinges. Refer to the
illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the nd a
showroom section of our website, subzero.com. For ques-
tions regarding the installation, call Sub-Zero Customer
Care at 800-222-7820.
WITHOUT FILLER STRIP FILLER STRIP
Opposite hinges
Same side hinges
subzero.com | 9
SITE PREPARATION
Plumbing Requirements
Installation must comply with all applicable plumbing codes.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must not interfere with the installation
of the anti-tip brackets.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. In this application, the water ltration
system must be bypassed by removing the lter. A copper
line is not recommended for this application.
PLUMBING REQUIREMENTS
Water Supply 1/4" OD copper, braided
stainless steel, or PEX tubing
Pressure 35–120 psi (2.4–8.3 bar)
Excess Line for Connection 36" (914)
Preparation
Uncrate the unit and inspect for damage. Remove the wood
base and discard the shipping bolts and brackets. Remove
and recycle packing materials. Do not discard the kickplate,
anti-tip brackets, and hardware.
Completely retract the front leveling legs to allow the unit to
be moved into position. The front and rear leveling legs can
be adjusted from the front once the unit is in position.
Remove the drain pan from the base of the unit to avoid
damage and to allow for proper placement of the appliance
dolly.
The grille assembly should be removed prior to moving the
unit. To remove, pull out on the bottom edge of the grille and
rotate upward. Loosen the back two grille mounting screws
and remove the front two grille mounting screws. Refer to
the illustrations below. With the grille held rmly, pull forward
to remove.
BACK GRILLE
SCREW
FRONT
GRILLE SCREW
Grille removal
Grille mounting screws
3" (76)
18" (457) 6" (152)
RIGHT SIDE
OF OPENING
AREA EXTENDS 1/2"(13)
FORWARD ON FLOOR
Water supply location
10 | Sub-Zero Customer Care 800.222.7820
SITE PREPARATION
WOOD FLOOR APPLICATION
After properly locating the anti-tip brackets in the opening,
drill pilot holes 3/16"(5) diameter maximum in the wall studs
or wall plate. Use the #12 screws and washers to secure the
brackets. Verify the screws penetrate through the ooring
material and into the wall studs or wall plate a minimum of
3/4"(19). Refer to the illustration below.
CONCRETE FLOOR APPLICATION
After properly locating the anti-tip brackets in the opening,
drill pilot holes 3/16"(5) diameter maximum in the wall studs
or wall plate. Drill 3/8"(10) diameter holes into the concrete
a minimum of 11/2"(38) deep. Use the #12 screws and
washers to secure the brackets to the wall, and use the 3/8"
wedge anchors to secure the brackets to the oor. Verify
the screws penetrate the wall studs or wall plate a minimum
of 3/4"(19). Refer to the illustration below.
4" (102)
MIN
24"
(610)
SUBFLOORING
WOOD FLOOR
WALL PLATE
FINISHED
FLOORING
4" (102)
MIN
24"
(610)
SUBFLOORING
CONCRETE
FLOOR
WALL PLATE
FINISHED
FLOORING
11/2"(38)
min
SUBFLOORING
CONCRETE
FLOOR
WALL PLATE
FINISHED
FLOORING
11/2"(38)
MIN
Wood oor
Concrete oor
Anti-Tip Bracket
WARNING
To prevent the unit from tipping forward, the anti-tip
brackets must be installed.
The two anti-tip brackets must be installed exactly 24"
(610) from the front of the opening to the back of the
brackets and a minimum of 4" (102) from the sides of the
opening. This depth will increase to 263/16"(665) for a ush
inset installation based on 3/4"(19) thick panels. Failure to
properly position the anti-tip brackets will prevent proper
engagement.
Use all anti-tip bracket hardware as instructed for wood or
concrete oors.
IMPORTANT NOTE: For wood or concrete oor applications,
if the #12 screws do not hit a wall stud or wall plate, use the
#8 screws and #12 washers with the wall anchors.
IMPORTANT NOTE: In some installations the subooring or
nished oor may necessitate angling the screws used to
fasten the anti-tip brackets to the back wall.
ANTI-TIP HARDWARE
2 Anti-tip brackets
12 #12 x 21/2" pan head screws
43/8"–16 x 33/4" wedge anchors
12 #12 at washers
4 #8–18 x 11/4" truss head screws
4 Nylon Zip-it®wall anchors
Dieses Handbuch passt für folgende Modelle
9
Inhaltsverzeichnis
Sprachen:
Andere Sub-Zero Kühlschrank Handbücher
Sub-Zero
Sub-Zero ICBBI-36F Bedienungsanleitung
Sub-Zero
Sub-Zero BI-48SD Montageanleitung
Sub-Zero
Sub-Zero UC-24R Bedienungsanleitung
Sub-Zero
Sub-Zero ICB700TCI Bedienungsanleitung
Sub-Zero
Sub-Zero BI-36R Montageanleitung
Sub-Zero
Sub-Zero 700TCI Gebrauchsanweisung
Sub-Zero
Sub-Zero BI-42S Montageanleitung
Sub-Zero
Sub-Zero DEC3650FI/R Bedienungsanleitung
Sub-Zero
Sub-Zero IC-24R-RH Bedienungsanleitung
Sub-Zero
Sub-Zero ICBDEC2450FI/R Bedienungsanleitung
Sub-Zero
Sub-Zero INTEGRATED REFRIGERATION Bedienungsanleitung
Sub-Zero
Sub-Zero 601R Betriebsanleitung
Sub-Zero
Sub-Zero Classic Series Bedienungsanleitung
Sub-Zero
Sub-Zero Built-in refrigerators Bedienungsanleitung
Sub-Zero
Sub-Zero INTEGRATED REFRIGERATION Bedienungsanleitung
Sub-Zero
Sub-Zero 736TCI Bedienungsanleitung
Sub-Zero
Sub-Zero Built-In Refrigeration Betriebsanleitung
Sub-Zero
Sub-Zero BI-42SD/S/PH Bedienungsanleitung
Sub-Zero
Sub-Zero 700BCI Bedienungsanleitung
Sub-Zero
Sub-Zero 600 Series Betriebsanleitung
Beliebte Kühlschrank Handbücher anderer Marken
Bonnet Neve
Bonnet Neve SKYVIEW PLUS Bedienungsanleitung
Zanussi Electrolux
Zanussi Electrolux ZERB 8441 Bedienungsanleitung
Sharp
Sharp SJ-BA31IEXW2-EU Bedienungsanleitung
CORBERO
CORBERO CC2300MCW Bedienungsanleitung
KitchenAid
KitchenAid 2205264 Bedienungsanleitung
Stengel
Stengel KU 1101 A++ Bedienungsanleitung
