Sub-Zero INTEGRATED REFRIGERATION Bedienungsanleitung

I STALLATIO GUIDE

ntegrated Refrigeration

mportant Note

To ensure the safe and efficient installation of Sub-Zero

equipment, please take note of the following types of

highlighted information throughout this guide:

IMPORTA T OTE highlights information that is

especially relevant to a problem-free installation.

CAUTIO signals a situation where minor injury or

product damage may occur if instructions are not

followed.

WAR I G states a hazard that may cause serious injury

or death if precautions are not followed.

Contents

Integrated Refrigeration ....................... 3

Model Specifications .......................... 4

Site Preparation .............................. 6

Integrated Installation ........................ 11

Service Information .......................... 19

Features and specifications in this guide and on the website

are subject to change at any time without notice. Check our

website, subzero.com, for the most up-to-date specifications.

Sub-Zero ntegrated Refrigeration

The importance of the installation of the Sub-Zero

integrated unit cannot be overemphasized. nstallation

should be done by a qualified installer.

Before you begin the installation process, it is recom-

mended that you read this entire installation guide. There

are key details that you should take special care to

observe during the installation. By reading these instruc-

tions carefully, you will make the installation process

easier, problem-free and, most importantly, safe.

Any questions or problems regarding the installation

should be directed to your Sub-Zero dealer or Sub-Zero

customer service at 800-222-7820. You may also check

the contact & support sectionofour website, subzero.com.

mportant product information, including the model and

serial number of your unit are listed on the product rating

plate. The rating plate is located inside the cabinet, to the

left of the upper drawer. Refer to the illustration below.

IMPORTA T OTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specified.

ntegrated Refrigeration 3

subzero.com

Location of rating plate.

RAT NG PLATE

Before You Start

Make sure that the finished rough opening where the

integrated unit is to be installed is properly prepared.

Refer to the specifications for your specific model on the

following pages. Make sure that the opening dimensions,

door and drawer clearances, electrical service and

plumbing are correct for the model you are about to

install.

IMPORTA T OTE: The inside edges of the rough

opening, as well as the sides and a portion of the

backside of the decorative panels will need to be finished,

as they will be exposed when the doors are open.

TOOLS A D MATERIALS REQUIRED

•Appliance dolly able to support 500 lbs (227 kg) and

adequate manpower to handle the weight of the unit.

•Phillips and slotted screwdrivers.

•Allen, standard and crescent wrenches.

•Various sized pliers.

•5/16" hex bolt nut driver.

•Cordless drill and assorted drill bits.

•Level—2' (.6 m) and 4' (1.2 m) recommended.

•4' (1.2 m) of 1/4" copper tubing and saddle valve for the

water line (4200880)—do not use self-piercing valves.

•Copper tubing cutter.

•Masonite, plywood, 1/8" pressed fiberboard, cardboard

or other suitable material to protect finished flooring.

•Appropriate materials to cover and protect the home

and its furnishings during installation.

Model Specifications 4

MODELS 700TR, 700TF(I) A D 700TC(I)

TALL UN TS

MODELS 700BR, 700BF(I) A D 700BC(I)

DRAWER UN TS

27" (686)

14"(356)

13/16"

(21)

341/2"

(876)

24"

(610)

203/8"

(518)

101/4"

(260)

131/4"

(337)

DIMENSIONS WILL VARY WITH PANEL THICKNESS

1/2"

(13)

3/8"

(10)

191/2"

(495)

251/2"

(648)

45/8"

(117)

80"

(2032)

TO TOP OF

OPENNG

24" (610)

789/16"

(1995)

93/4"

(248)

(102)

HEIGHT DIMENSIONS ± 1/2"(13)

27" (686)

341/2"

(876)

24"

(610)

203/8"

(518)

DIMENSIONS WILL VARY WITH PANEL THICKNESS

1/2"

(13)

3/8"

(10)

191/2"

(495)

257/8"(657)

24" (610)

93/4"(248)

(102)

101/4"

(260)

131/4"

(337)

HEIGHT DIMENSIONS ± 1/2"(13)

Overall Dimensions

27" (686) MODELS

Model Specifications 5

subzero.com

MODELS 736TR, 736TFI A D 736TCI

TALL UN TS

Interior Capacity R cu ft (L) F cu ft (L)

27" (686) TALL U ITS

700TR 15.5 (439)

700TF( ) 15.3 (433)

700TC( ) 10.2 (289) 5.1 (144)

27" (686) DRAWER U ITS

700BR 5.3 (150)

700BF( ) 5.1 (144)

700BC( ) 2.9 (82) 2.1 (59)

36" (914) TALL U ITS

736TR 20.9 (592)

736TF 21.5 (609)

736TC 13.3 (377) 7.1 (201)

nterior Capacity and Weight

36" (914)

14"(356)

80"

(2032)

TO TOP OF

OPENNG

24" (610)

15/16"

(33)

7713/16"

(1976)

341/2"

(876)

24"

(610)

203/8"

(518)

101/4"

(260)

131/4"

(337)

93/4"

(248)

(102)

DIMENSIONS WILL VARY WITH PANEL THICKNESS

1/2"

(13)

3/8"

(10)

191/2"

(495)

341/2"

(876)

7" (178)

HEIGHT DIMENSIONS ± 1/2"(13)

Shipping Weight lbs (kg)

700TR, 700TF( ) and 700TC( ) 360 (163)

700BR, 700BF( ) and 700BC( ) 190 (86)

736TR, 736TF and 736TC 480 (218)

Overall Dimensions

36" (914) MODELS

Site Preparation 6

Opening Width A

700TR, 700TF( ) and 700TC( ) 27" (686)

700BR, 700BF( ) and 700BC( ) 27" (686)

736TR, 736TF and 736TC 36" (914)

IMPORTA T OTE: The depth of each integrated model is

24" (610) from the front of the unit to its back. Your design may

necessitate moving the unit back or cabinets forward to achieve

a flush fit. This will require a minimum rough opening depth of

25" (635).

25" (635)

OPENING

DEPTH

OPENING WIDTH

25" (635)

OPENING DEPTH

OPENING

HEIGHT

TOP VIEW

FRONT VIEWSIDE VIEW

Opening Dimensions

I TEGRATED MODELS

Site Preparation 7

subzero.com

Electrical Requirements

The electrical supply should be located within the shaded

area shown in the illustrations. Follow the National

Electrical Code and local codes and ordinances when

installing the receptacle. A separate circuit, servicing only

this appliance is required.

IMPORTA T OTE: t is critical that the electrical outlet be

located within the shaded area shown so it does not inter-

fere with installation of the anti-tip bracket. t must be

flush with the back wall and positioned with the grounding

prong to the right of the thinner blades.

IMPORTA T OTE: A ground fault circuit interrupter

(GFC ) is not recommended and may cause interruption of

operation.

Electrical Requirements

Power Supply 115 V AC, 60 Hz

Circuit Breaker 15 amp

Receptacle 3-prong grounding-type

13" (330)

1/4"(6)

41/2"

(114)

POSITION OUTLET WITH

GROUNDING PRONG

TO THE RIGHT

FLOOR

21/2"(64)

FRONT VIEW

27" (686) models. 36" (914) models.

171/2"(445)

41/2"

(114)

POSITION OUTLET WITH

GROUNDING PRONG

TO THE RIGHT

FRONT VIEW

FLOOR

21/2"(64)

1/4"(6)

Do not use an extension cord or two-prong adapter.

Do not remove the power supply cord ground prong.

The outlet must be checked by a qualified electrician

to be sure that it is wired with the correct polarity.

Verify that the outlet is properly grounded.

Site Preparation 8

Plumbing Requirements

For integrated models with an automatic ice maker, the

water supply line should be located through the floor or

back wall, within the shaded area shown in the illustra-

tions. Routing the line in these locations will avoid any

interference with the anti-tip bracket.

The water supply line should be connected to the house

supply with an easily accessible shut-off valve between

the supply and the unit. Do not use self-piercing valves.

A saddle valve kit (4200880) is available from your

Sub-Zero dealer.

An in-line filter is required when water conditions have

a high sediment content.

A reverse osmosis system can be used provided there is

constant water pressure of 20 psi (1.4 bar) to 100 psi

(6.9 bar) supplied to the unit at all times. n some cases,

a reverse osmosis water filter system may not be able to

maintain the minimum pressure consistently.

IMPORTA T OTE: Do not route the water supply line in

front of the compressor tray. The tray must be slid forward

for service.

Plumbing Requirements

Water Supply Line 1/4" OD copper line

Water Pressure 20–100 psi (1.4–6.9 bar)

Excess Water Line for Connection 27" (686)

3" (76)

(229)

3/4"

(19)

FLOOR

21/2"(64)

FRONT VIEW

27" (686) models.

(229)

(152)

TOP VIEW

11/2"

(38)

21/2"

(64)

BACK

WALL

131/2"

(343)

3" (76)

FRONT VIEW

3/4"

(19)

FLOOR

21/2"(64)

36" (914) models.

131/2"

(343)

TOP VIEW

(152) 11/2"

(38)

21/2"

(64)

BACK

WALL

Site Preparation 9

subzero.com

An anti-tip bracket and hardware is provided with the inte-

grated unit. Placement of the anti-tip bracket is critical to

a stable installation. The anti-tip bracket must be installed

on a solid base.

f you are installing the unit in a space deeper than 24"

(610), be sure to locate the anti-tip bracket so that it

engages the unit properly. t is important that the anti-tip

bracket is placed 24" (610) from the front of the unit

(without panels) to the back of the anti-tip bracket.

IMPORTA T OTE: n some installations the subflooring

or finished floor may require angling the wood screws

used to fasten the anti-tip bracket to the back wall. Refer

to the illustrations.

WOOD FLOOR APPLICATIO S

Use the six #12 x 21/2" wood screws and the six 1/4" flat

washers provided. Drill pilot holes 3/16" (5) diameter

maximum, and be sure that the screws penetrate through

the flooring material and into the wall plate a minimum of

3/4" (19). Be sure that the screws hold tight. Refer to the

illustration below.

CO CRETE FLOOR APPLICATIO S

Use the two 3/8" x 33/4" concrete wedge anchors, two

#12 x 21/2" wood screws and two 1/4" flat washers

provided. Be sure that the anchors and screws hold tight.

Refer to the illustration below.

Anti-Tip Bracket nstallation

Make sure there are no electrical wires or plumbing

in the area which the screws could penetrate.

To prevent the unit from tipping forward and provide

astable installation, the unit must be secured in place

with the anti-tip brackets shipped with the unit.

Anti-Tip Bracket Placement A

27" (686) Models 131/2"(343)

36" (914) Models 18" (457)

FINISHED FLOORING

UNDERLAYMENT

CONCRETE

FLOOR

WALL PLATE

SUBFLOORING

Wood floors. Concrete floors.

11/2"

min

(38)

FINISHED FLOORING

UNDERLAYMENT

CONCRETE

FLOOR

WALL PLATE

SUBFLOORING

Site Preparation 10

Anti-Tip Bracket nstallation

I STALL CO CRETE WEDGE A CHORS:

1) Drill a 3/8" (10) diameter hole any depth exceeding the

minimum embedment. Clean the hole or continue

drilling additional depth to accommodate drill fines.

Use a carbide drill bit manufactured within ANS

B94.12-77.

2) Assemble the washer and nut flush with the end of

anchor to protect threads. Drive the anchor through the

material to be fastened until the washer is flush with

the surface material.

3) Expand the anchor by tightening the nut 3–5 turns past

hand-tight position or to 25 foot-pounds of torque.

Always wear safety glasses and use other necessary

protective devices or apparel when installing or

working with anchors.

Anchors are not recommended for use in lightweight

masonry material such as block or brick, or for use

in new concrete which has not had sufficient time to

cure. The use of core drills is not recommended to

drill holes for the anchors.

Unpacking and Moving

Uncrate the unit and inspect for any damages. Remove

the wood base and discard the shipping bolts that hold the

wood base to the bottom of the unit. Remove and discard

all packing materials.

Retract the front leveling legs all the way up to allow the

unit to be moved into position more easily. You will extend

the leveling legs when the unit is in its final position to

reduce the possibility of the unit tipping forward.

Use an appliance dolly to move the integrated unit near

the installation opening. Position the dolly at the side of

the unit to prevent damage to finished surfaces.

Andere Handbücher für INTEGRATED REFRIGERATION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sub-Zero Kühlschrank Handbücher

Sub-Zero

Sub-Zero ICBBI-36R Betriebsanleitung

Sub-Zero

Sub-Zero 200 Series Bedienungsanleitung

Sub-Zero

Sub-Zero 661 Bedienungsanleitung

Sub-Zero

Sub-Zero 500 Series Technisches Handbuch

Sub-Zero

Sub-Zero IC-27R Bedienungsanleitung

Sub-Zero

Sub-Zero PRO 48 Bedienungsanleitung

Sub-Zero

Sub-Zero 736TCI Bedienungsanleitung

Sub-Zero

Sub-Zero UC-24RO Bedienungsanleitung

Sub-Zero

Sub-Zero 200 Series Bedienungsanleitung

Sub-Zero

Sub-Zero 648PRO Bedienungsanleitung

Sub-Zero

Sub-Zero 600 Series BI-30U Bedienungsanleitung

Sub-Zero

Sub-Zero BI-42S Montageanleitung

Sub-Zero

Sub-Zero UC24CIRH Bedienungsanleitung

Sub-Zero

Sub-Zero 650/B Bedienungsanleitung

Sub-Zero

Sub-Zero IC-24R Bedienungsanleitung

Sub-Zero

Sub-Zero Built-In Refrigeration Betriebsanleitung

Sub-Zero

Sub-Zero ICB700 T Series Bedienungsanleitung

Sub-Zero

Sub-Zero PRO 48 Bedienungsanleitung

Sub-Zero

Sub-Zero IC-30RID Bedienungsanleitung

Sub-Zero

Sub-Zero Integrated Series Bedienungsanleitung

Sub-Zero

Sub-Zero 600 Series BI-48S Bedienungsanleitung

Sub-Zero

Sub-Zero ID-30CI Bedienungsanleitung

Sub-Zero

Sub-Zero Classic Series Bedienungsanleitung

Sub-Zero

Sub-Zero Sub-Zero BI series Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung