Sub-Zero Built-in Series Bedienungsanleitung

WARNING

Built-In units are heavy and can be unstable when

attempting to install them. When moving a Built-In unit,

keep the doors and drawers taped closed. The anti-tip

components supplied with Built-In units must be used as

speciﬁed in the installation guide. The front leveling legs of

a Built-In unit must be extended to the ﬂoor to complete

the installation. If a Built-In unit were to tip and fall, it could

cause serious injury or death!

CONTENTS

4 Bolt, Tensilock 5/16-18 × 3/4

1 Clip, cord plastic 5/16 × 1/2

6 Screw, #8-32 × 1/2pan head

4 Threaded insert, 5/16-18 hx opn

1 Trim, dual install center long

1 Bracket, dual install bot

4 Screw, 5/16 × 3/4thread-forming

1 Bracket, dual install top

3 Bracket assembly, dual trim

1 Threaded insert, install tool

1 Heater assembly, dual installation

1 Shim, assembly main frame

6 Nut, 10-24 hex ﬂange lock

1 Machine screw, #10-24 × 21/4

1 Nut, #10-24 with nylon insert

1 Instructions, dual installation

INSTALL THE HEATER

Note: The heater assembly MUST be attached to the right

side of the left-hand unit.

1Clear the foil from the mounting holes of the heater

assembly.

2Place the heater against the right-hand side of the unit

with wires up and foil side in, positioning the heater 2”

(51 mm) from the top edge of the cabinet and 1” (25

mm) from the rear edge of the cabinet.

3Using the heater as a template, mark the heater

mounting holes on the cabinet with a pencil, then

remove the heater.

4Drill a 7/64" (3 mm) hole at each marked location.

Note: To avoid drilling through the inner liner, use a

short drill bit inserted into the drill chuck so that no

more than 1/2” (13 mm) to 3/4” (19 mm) of bit is

protruding.

5Attach the heater to the unit using the #8-32 × 1/2" pan

head screws into the drilled holes.

6Remove the four-prong safety plug from the panel-

mounted four-prong receptacle at the rear side of

the power cord box.

7Connect the heater’s four-prong plug to the receptacle.

8Attach the 5/16" × 1/2" plastic cord clip in a convenient

location near the water ﬁlter.

9Route the heater wires through the plastic cord clip and

any other available wire clips.

1”

2”

Power Cord Box and

4-Prong Heater Plug

Connection (Rear View)

INSTALL THE CENTER TRIM

Note: Assemble the center trim piece and trim brackets

ﬁrst, then attach the trim to the right-hand side of the left-

hand unit.

1Attach the three L-shaped dual trim bracket assemblies

to the dual install center trim piece using the nuts

provided. Do not tighten the nuts at this time.

Built-In Series Dual Installation Kit

subzero.com 800.222.7820

7004565 REV. E 06/2018 Page 1 of 4 *7004565$REV.$E*

2With the trim brackets loosely attached, hold the center

trim piece at about a 75° angle against the right-hand

side main frame.

3Rotate the center trim piece toward the unit so the trim

brackets hook in behind the main frame.

4Align the bottom of the center trim piece with the

bottom of the main frame.

5Tighten the nuts.

Main

Frame

Center

Trim

(Top View)

Main

Frame

Center

Trim

INSTALL THE UNIT INTO THE LEFT-HAND SIDE OF THE

ROUGH-IN OPENING

Install the unit into the left-hand side of the rough-in

opening as speciﬁed in the installation guide.

INSTALL THE MAIN FRAME SHIM

Note: The shim assembly must be attached to the rear of

the left-hand side main frame of the right-hand unit.

1Remove the left-side main frame from the right-hand

unit.

2Remove the backing paper from the double-stick tape

that is attached to the main frame shim.

3Align the shim to the main frame so the two holes in the

shim are at the same height as the two middle main

frame mounting holes. Make sure the shim is tight to

the bend in the main frame, and the shim is in front of

the section of the main frame with the mounting holes.

4Attach the shim to the main frame. Make sure the holes

in the shim are next to but not over the main frame

mounting holes.

5Reattach the left-side main frame to the right-hand unit.

Shim

Left Main Frame

Top View of

Main Frame

and Shim

Built-In Series Dual Installation Kit

subzero.com 800.222.7820

Page 2 of 4

INSTALL THE SECOND UNIT TO THE RIGHT OF THE FIRST

Install, level, and align the unit until its main frame

bumps against the ﬂange of the center trim piece, and

the bottom of the main frame aligns with the bottom of

the center trim piece.

Top View of

Main Frames

with Center

Trim Installed

JOIN THE UNITS TOGETHER AT THE BOTTOM

1Using a 1/2" wrench, install or adjust the bolts at the

bottom adjoining corners of the appliances so that

there is a 1/8" (3 mm) to 1/4” (6 mm) gap between the

bolt heads and the unit shell bottom.

▪For All-Refrigerator and All-Freezer Models:

Loosen the four bolts (two for each unit).

▪For Over/Under Models: Install four 5/16” × 3/4”

thread-forming screws (two for each unit).

2Align the four notches of the dual-installation bottom

bracket with the four bolts at the bottom adjoining

corners of the appliances.

3Push the bracket into position.

4Tighten the bolts.

1/8”-1/4”

Bottom View of Bolts and Bracket

INSTALL THE THREADED INSERTS AT THE TOP (FOR OVER/

UNDER MODELS)

Note: For all-refrigerator and all-freezer models, the

threaded inserts are already installed at the top. Skip these

instructions.

1Open both grilles, and locate the hexagonal holes at

the top adjoining corners of the units (two for each

unit).

2For each of the hexagonal holes:

a) Use a small screwdriver or similar tool to remove

the foam insulation from each hole to a depth of no

more than 1/2” (13 mm).

b) Screw the thread insert installation tool into a

threaded insert.

c) Position the threaded insert over one of the

hexagonal holes, and tap the threaded insert into

the hole.

d) Using a 1/2" wrench at the tool bolt top and a 9/16”

open-end wrench at the collar, spin the tool bolt

clockwise while holding the collar stationary. Stop

when it will spin no further.

e) Remove the tool from the insert.

(Grilles removed

for clarity)

Tool Bolt

Tool Collar

Insert

Hexagonal Hole

Built-In Series Dual Installation Kit

subzero.com 800.222.7820

Page 3 of 4

3Tighten the bolts.

(Grilles

removed

for clarity)

SECURE THE GRILLE FRAMES TOGETHER

1Secure the grilles together by inserting the #10-24 ×

21/4" machine screw into the upper rear holes in the

grille brackets.

2Attach the #10-24 nut to the machine screw, and

tighten it.

3Close the grilles.

#10-24 × 21/4”

Machine Screw

Front View

#10-24 Nut

Built-In Series Dual Installation Kit

subzero.com 800.222.7820

Page 4 of 4

JOIN THE UNITS TOGETHER AT THE TOP

1Working the dual-installation top bracket in from the

side, line up the holes of the top bracket with the

threaded inserts at the top adjoining corners of the

appliances.

2Insert four 5/16-18 × 3/4” Tensilock bolts through the

bracket into the threaded inserts.

Andere Handbücher für Built-in Series

Andere Sub-Zero Kühlschrank Handbücher

Sub-Zero

Sub-Zero UC-24R Bedienungsanleitung

Sub-Zero

Sub-Zero 400 Series Installations- und Betriebshandbuch

Sub-Zero

Sub-Zero 700-2 Series Bedienungsanleitung

Sub-Zero

Sub-Zero PRO 48 Montageanleitung

Sub-Zero

Sub-Zero 601F Bedienungsanleitung

Sub-Zero

Sub-Zero 700BC Bedienungsanleitung

Sub-Zero

Sub-Zero UC-24R Bedienungsanleitung

Sub-Zero

Sub-Zero 600 Series Betriebsanleitung

Sub-Zero

Sub-Zero BI-42SD Montageanleitung

Sub-Zero

Sub-Zero 700BC Bedienungsanleitung

Sub-Zero

Sub-Zero BI-48SD Montageanleitung

Sub-Zero

Sub-Zero BI-30UG Bedienungsanleitung

Sub-Zero

Sub-Zero ICBBI-36R Betriebsanleitung

Sub-Zero

Sub-Zero BI-42SID Bedienungsanleitung

Sub-Zero

Sub-Zero Built-In Refrigeration Bedienungsanleitung

Sub-Zero

Sub-Zero INTEGRATED REFRIGERATION Bedienungsanleitung

Sub-Zero

Sub-Zero IC-27R Bedienungsanleitung

Sub-Zero

Sub-Zero DEC3650RL Bedienungsanleitung

Sub-Zero

Sub-Zero BI-42UFDID/O Bedienungsanleitung

Sub-Zero

Sub-Zero BI-36F Montageanleitung

Sub-Zero

Sub-Zero IT36CIRH Bedienungsanleitung

Sub-Zero

Sub-Zero BI-36RG Montageanleitung

Sub-Zero

Sub-Zero 600 Series BI-30U Bedienungsanleitung

Sub-Zero

Sub-Zero BI-36R Montageanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung