Sub-Zero IC-27R Bedienungsanleitung

Integrated Refrigeration Installation Guide

INTEGRATED REFRIGERATION

Contents

3Integrated Refrigeration

4Opening Dimensions

5Electrical

6Plumbing

7Preparation

7Anti-Tip Bracket

9Placement

9Alignment

10 Water Line

10 Custom Panels

13 Panel Installation

15 Completion

Features and specications are subject to change at any

time without notice. Visit subzero.com/specs for the most

up-to-date information.

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

subzero.com

Product Information

Important product information including the model and

serial number of the unit are listed on the product rating

plate. For column models, the rating plate is located inside

the middle drawer near the drawer guide opposite the hinge.

For tall and drawer models, the rating plate is located inside

the cabinet, to the left of the upper drawer. Refer to the

illustrations below.

If service is necessary, contact Sub-Zero factory certied

service and have the model and serial number of the unit.

For the name of the nearest Sub-Zero factory certied

service or for questions regarding the installation, visit the

contact & support section of our website, subzero.com or

call Sub-Zero customer care at 800-222-7820.

INTEGRATED REFRIGERATION

Tools and Materials

•Screwdrivers—standard, Phillips and Torx.

•Power drill.

•Drill bits (masonry bits required for concrete installation).

•Standard socket and wrench set.

•2' and 4' levels.

•Tubing cutter.

•3' (.9 m) of 1/4" OD copper, braided stainless steel or

PEX tubing.

•Saddle valve.

•Material to protect home, ooring and cabinetry during

installation.

Column models.

Tall and drawer models.

RATING

PLATE

RATING

PLATE

Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Opening Dimensions

INTEGRATED MODELS

25" (635)

OPENING

DEPTH

OPENING WIDTH

OPENING

HEIGHT

SIDE VIEW

TOP VIEW

FRONT VIEW

OPENING DIMENSIONS

COLUMN W H

IC-27R and IC-27FI 27" (686) 81" (2057)

TALL W H

700TR, 700TFI, 700TCI 27" (686) 80" (2032)

736TR, 736TFI, 736TCI 36" (914) 80" (2032)

DRAWERS W H

700BR, 700BF(I), 700BC(I) 27" (686) 341/2"(876)

The depth of each integrated model is 24" (610). Allow for

panel thickness when planning the nished opening depth.

subzero.com

SITE PREPARATION

CAUTION

The outlet must be checked by a qualied electrician to

be sure that it is wired with the correct polarity. Verify

that the outlet is properly grounded.

WARNING

Do not use an extension cord, two-prong adapter or

remove the power cord ground prong.

Electrical

Installation must comply with all applicable electrical codes.

The electrical supply must be located within the shaded

area shown in the illustration and chart below. A separate

circuit, servicing only this appliance is required. A ground

fault circuit interrupter (GFCI) is not recommended and may

cause interruption of operation.

The electrical outlet must be positioned with the grounding

prong to the right of the thinner blades.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

13" (330)

1/4"

(6)

41/2"

(114)

LEFT SIDE

OF OPENING

FLOOR

21/2"

(64)

FRONT VIEW

171/2" (445)

41/2"

(114)

FRONT VIEW

FLOOR

1/4"

(6)

LEFT SIDE

OF OPENING

21/2"

(64)

Electrical—27" models.

Electrical—36" models.

Sub-Zero Customer Care 800.222.7820

Plumbing

Installation must comply with all applicable plumbing codes.

For models with an ice maker, the water supply line should

be located within the shaded area shown in the illustrations.

The water supply line should be connected to the house

supply with an easily accessible shut-off valve. Do not use

self-piercing valves. The water supply line must be ush

to the oor and not interfere with installation of the anti-tip

bracket. Do not route the water supply line in front of the

compressor tray. The tray must be slid forward for service.

An in-line lter is required when water conditions have a

high sediment content.

A reverse osmosis system can be used provided there is

constant water pressure of 20–100 psi (1.4–6.9 bar) supplied

to the unit at all times. In some cases, a reverse osmosis

water lter system may not be able to maintain the minimum

pressure consistently. A copper line is not recommended for

this application.

PLUMBING REQUIREMENTS

Water Supply 1/4" OD copper, braided

stainless steel or PEX tubing

Pressure 20–100 psi (1.4–6.9 bar)

Excess Line for Connection 36" (914)

SITE PREPARATION

3" (76)

(229)

3/4"

(19)

FLOOR

21/2" (64)

FRONT VIEW

(229)

(152)

TOP VIEW

11/2"

(38)

21/2"(64)

BACK

WALL

11/2"(38)

Plumbing—27" models (rear).

Plumbing—27" models (bottom).

131/2"

(343)

3" (76)

FRONT VIEW

3/4"

(19)

FLOOR

21/2" (64)

131/2"

(343)

TOP VIEW

(152) 11/2"

(38)

BACK

WALL

21/2"(64)

11/2"(38)

Plumbing—36" models (rear).

Plumbing—36" models (bottom).

subzero.com

SITE PREPARATION

Preparation

Uncrate the unit and inspect for damage. Remove the wood

base and discard shipping bolts and brackets. Remove and

recycle packing materials. Do not discard the kickplate,

anti-tip bracket and hardware. Remove the kickplate by

removing the screws holding it in place.

IMPORTANT NOTE: For drawer models, the upper drawer

has a control cable that must be disconnected before

removing the drawer. Refer to the illustration below.

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

bracket must be installed.

The back of the anti-tip bracket must be installed 24" (610)

from the front of the unit (without panels).

Use all anti-tip bracket hardware as instructed for wood or

concrete oors.

IMPORTANT NOTE: For wood or concrete oor applications,

if the #12 screws do not hit a wall stud or wall plate, use the

#8 screws and #12 washers with the wall anchors.

IMPORTANT NOTE: In some installations the subooring or

nished oor may necessitate angling the screws used to

fasten the anti-tip bracket to the back wall.

ANTI-TIP HARDWARE

1 Anti-tip bracket

12 #12 x 21/2" pan head screws

43/8"–16 x 33/4" wedge anchors

12 #12 at washers

4 #8–18 x 11/4" truss head screws

4 Nylon Zip-it®wall anchors

Control cable (drawer models).

Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

CONCRETE WEDGE ANCHOR INSTALLATION:

1Drill a 3/8"(10) diameter hole any depth exceeding the

minimum embedment. Clean the hole or drill additional

depth to accommodate drill nes.

2Assemble the washer and nut ush with the end of

anchor to protect threads. Drive the anchor through the

material to be fastened until the washer is ush with the

surface material.

3Expand the anchor by tightening the nut 3–5 turns past

hand-tight position or to 25 foot-pounds of torque.

WARNING

Verify there are no electrical wires or plumbing in the

area which the screws could penetrate.

CAUTION

Always wear safety glasses and use other neces-

sary protective devices or apparel when installing or

working with anchors.

Anchors are not recommended for use in lightweight

masonry material such as block or brick, or for use in

new concrete which has not had sufcient time to cure.

The use of core drills is not recommended to drill holes

for the anchors.

Anti-Tip Bracket

WOOD FLOOR APPLICATION

After properly locating the anti-tip bracket in the opening,

drill pilot holes 3/16"(5) diameter maximum in the wall studs

or wall plate. Use the #12 screws and washers to secure the

brackets. Verify the screws penetrate through the ooring

material and into wall studs or wall plate a minimum of 3/4"

(19). Refer to the illustration and chart below.

CONCRETE FLOOR APPLICATION

After properly locating the anti-tip bracket in the opening,

drill pilot holes 3/16"(5) diameter maximum in the wall studs

or wall plate. Drill 3/8"(10) diameter holes into the concrete

a minimum of 11/2"(38) deep. Use the #12 screws and

washers to secure the brackets to the wall, and use the 3/8"

wedge anchors to secure the brackets to the oor. Verify the

screws penetrate wall studs or wall plate a minimum of 3/4"

(19). Refer to the illustration and chart below.

ANTI-TIP BRACKET PLACEMENT

WIDTH A

27" Models 131/2"(343)

36" Models 18" (457)

SUBFLOORING

WOOD FLOOR

WALL PLATE

FINISHED

FLOORING

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

11/2"(38)

min

Wood oor.

Concrete oor.

subzero.com

INSTALLATION

Placement

CAUTION

Before moving the unit into position, secure the door/

drawers closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

Front and rear leveling legs can be adjusted from the front

once the unit is positioned.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

Plug the power cord into the grounded outlet and roll the

unit into position. Verify the anti-tip bracket is properly

engaged.

Alignment

LEVELING

Once the unit is in position, height adjustment can be made

from the front. Using a standard screwdriver, turn front

leveling legs clockwise to raise the unit or counterclockwise

to lower. Using a Phillips drive, turn rear adjustment screws

clockwise to raise the unit or counterclockwise to lower. Use

the lowest torque setting when using a power drill (18 revo-

lutions equals 1/16"of height adjustment). Do not turn the

rear leveling legs by hand. Refer to the illustrations below.

Level the unit to the oor, not surrounding cabinetry. This

could affect the operation of the unit, such as door closing.

When the unit is properly leveled, door/drawer adjustments

are less likely to be necessary.

Secure the unit in place using the side mounting clips and

#8 x 1/2" screws provided.

WARNING

To reduce the possibility of the unit tipping forward,

the front leveling legs must be in contact with the oor.

Front adjustment.

Rear adjustment.

Sub-Zero Customer Care 800.222.7820

INSTALLATION

Water Line

Purge the water line prior to nal connection to the unit. This

will remove any debris that may be present in the tubing

from installing the new water line. Connect the plastic tubing

from the unit to the house water supply line with the tting

connection kit provided. Check all water line ttings for

leaks. Refer to the illustration below.

IMPORTANT NOTE: Water lines can not be exposed to

freezing temperatures.

PEX

TUBING

Water line.

Custom Panels

For integrated models, custom door panels and handle

hardware must be installed. Stainless steel panels are

available through an authorized Sub-Zero dealer. For local

dealer information, visit the nd a showroom section of our

website, subzero.com.

The thickness of the custom panel can vary. A minimum

5/8"(16) thick panel is required, but the thickness can be

increased provided it does not exceed the maximum panel

weight indicated in the chart below. The depth of each

integrated model is 24" (610). Allow for panel thickness when

planning the nished opening depth.

PANEL REQUIREMENTS

COLUMN MAX WEIGHT

27" (686) 65 lbs (29 kg)

TALL (DOOR) MAX WEIGHT

27" (686) 40 lbs (18 kg)

36" (914) 53 lbs (24 kg)

DRAWER MAX WEIGHT

27" (686) 12 lbs (5 kg)

36" (914) 16 lbs (7 kg)

PANEL THICKNESS MINIMUM

All Panels 5/8"(16)

Andere Handbücher für IC-27R

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sub-Zero Kühlschrank Handbücher

Sub-Zero

Sub-Zero UC-24 series Bedienungsanleitung

Sub-Zero

Sub-Zero Sub-Zero PRO series Bedienungsanleitung

Sub-Zero

Sub-Zero Built-In Refrigeration Bedienungsanleitung

Sub-Zero

Sub-Zero UC-24RO Bedienungsanleitung

Sub-Zero

Sub-Zero BI-36UG Montageanleitung

Sub-Zero

Sub-Zero IT-30RID Bedienungsanleitung

Sub-Zero

Sub-Zero ID-36RP Bedienungsanleitung

Sub-Zero

Sub-Zero BI-42S Bedienungsanleitung

Sub-Zero

Sub-Zero UC-24C Montageanleitung

Sub-Zero

Sub-Zero BI-36UFD Bedienungsanleitung

Sub-Zero

Sub-Zero ICBBI-36R Leitfaden

Sub-Zero

Sub-Zero DEC3650FI/R Bedienungsanleitung

Sub-Zero

Sub-Zero 695 Bedienungsanleitung

Sub-Zero

Sub-Zero Built-in Series Bedienungsanleitung

Sub-Zero

Sub-Zero PRO 48 Bedienungsanleitung

Sub-Zero

Sub-Zero 601R Bedienungsanleitung

Sub-Zero

Sub-Zero ICBBI-36R Leitfaden

Sub-Zero

Sub-Zero 648PRO Bedienungsanleitung

Sub-Zero

Sub-Zero BI-42SD Bedienungsanleitung

Sub-Zero

Sub-Zero 200 Series Bedienungsanleitung

Sub-Zero

Sub-Zero UC-24BG Montageanleitung

Sub-Zero

Sub-Zero Designer Series Bedienungsanleitung

Sub-Zero

Sub-Zero BI-36S Montageanleitung

Sub-Zero

Sub-Zero UC-24B Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung