Sunbeam HE2800 Bedienungsanleitung

Oscillating Digital Ceramic

Heater

Instruction Booklet

HE2800

Please read these instructions carefully

and retain for future reference.

Sunbeam’s Safety Precautions 1

Safety Precautions for your heater 2

Sunbeam’s Total Safety System 3

Features of your Oscillating Digital

Ceramic Heater 4

Using your Oscillating Digital

Ceramic Heater 6

Resetting the safety auto shut off 8

Care and cleaning 8

Contents

Sunbeam are very safety conscious when

designing and manufacturing consumer products,

but it is essential that the product user also

exercise care when using an electrical appliance.

Listed below are precautions which are essential

for the safe use of an electrical appliance:

• Read carefully and save all the instructions

provided with an appliance.

• Always turn the power off at the power outlet

before you insert or remove a plug. Remove

by grasping the plug - do not pull on the cord.

• Turn the power off and remove the plug

when the appliance is not in use and

before cleaning.

• Do not use your appliance with an extension

cord unless this cord has been checked

and tested by a qualified technician or

service person.

• Always use your appliance from a power

outlet of the voltage (A.C. only) marked

on the appliance.

• Close supervision is necessary when your

appliance is being used near children or

infirm persons.

• Never leave an appliance unattended while

in use.

• Young children should be supervised to ensure

that they do not play with the appliance.

• Do not use an appliance for any purpose

other than its intended use.

• Do not place an appliance on or near a hot gas

flame, electric element or on a heated oven.

Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang

over the edge of a table or bench top or touch

any hot surface.

• For safety reasons and to avoid maintenance

by unskilled persons, some appliances are

‘sealed’ using tamperproof screws. Such

appliances should always be returned to the

nearest Sunbeam Appointed Service Centre

for adjustment or repair if required.

• Do not operate any electrical appliance with a

damaged cord or after the appliance has been

dropped or damaged in any manner. If damage

is suspected, return the appliance to the

nearest Sunbeam Appointed Service Centre

for examination, repair or adjustment.

• For additional protection, Sunbeam

recommend the use of a residual current

device (RCD) with a tripping current not

exceeding 30mA in the electrical circuit

supplying power to your appliances.

• Do not immerse the appliance in water

or any other liquid unless recommended.

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

• This heater becomes hot during use. To avoid

burns, do not let bare skin touch hot surfaces.

If provided, use handles when moving this

heater. Keep combustible materials such as

furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (90cm) away from the

front of the heater and keep them away from

the sides and rear.

• Extreme caution is necessary when any heater

is used by or near children or invalids and

whenever the heater is left unattended.

• Always unplug the heater when not in use.

• Do not use outdoors.

• Do not run the cord of the heater under

carpeting. Do not cover the cord with throw

rugs, runners or other floor coverings. Arrange

the cord away from traffic areas where it will

not be tripped over.

• Do not locate the heater immediately below a

socket outlet.

• Do not use this heater in the immediate

surrounds of a bath, shower, laundry area or

swimming pool.

• Do not insert or allow foreign objects to enter

any ventilation or exhaust openings as this may

cause electric shock or fire, or damage to the

heater.

• To prevent a possible fire, do not block air

intakes or exhaust in any manner. Do not use

on soft surfaces, such as beds, where opening

may become blocked.

• A heater has hot and arcing or sparing parts

inside. Do not use it in areas where petrol,

paint or flammable liquids are used or stored.

Important instructions – retain for

future use.

Safety auto shut off

Your Sunbeam Oscillating Digital Ceramic

Heater is equipped with a safety system

that detects any abnormally high

temperatures within the heater and

automatically shuts it off to prevent

overheating. This first stage of the safety

system requires the user to manually reset

the heater for it to resume operation.

For instructions on how to reset your

heater, see page 8.

Thermal back-up fuse

In addition to this automatic cut off, your

heater contains a thermal back-up fuse to

provide additional back-up protection. If

the heater is in an overheat situation, the

back-up fuse will open, stopping the power

flow to the ceramic heating discs and fan.

This fuse cannot be reset, so in the event

that the back-up fuse is activated, the

heater will need to be replaced.

Sunbeam’s Total Safety System

Control panel

The compact control panel houses all of the buttons

required to operate the various functions of the

heater.

Mode button

Pres the mode button to select the desired operating

mode: Low Heat, High Heat or Auto mode.

Auto mode

Select the AUTO mode to operate the thermostat.

Use the Temp + and – buttons to select your desired

temperature. Once the set temperature is reached the

thermostat will cycle the heater on and off to

maintain it.

Timer function

The timer function allows you to set the heater to

switch itself off automatically after a specified period

of time, from 1 to 8 hours.

Oscillating function

The heater oscillates 120° on the base, providing

greater heat coverage to gradually warm the entire

room.

Features of your Oscillating Digital

Ceramic Heater

LCD screen

The LCD screen displays the current

settings, including the ambient room

temperature, the selected mode or heat

setting, and the timer icon if activated. It

features a blue backlight for easy

adjustment in the dark.

Remote control

The handy remote allows you to control the

heater from wherever you are in the room.

Switch the unit on or off, adjust the heat or

temperature setting, activate the oscillation,

or set the timer, all at the touch of a button.

Batteries are included.

Instant tip over cut out

The instant tip over cut out interrupts the

power to the heating element and fan if the

heater is accidentally tipped over. The

heater will not resume operation until it is

replaced in the upright position.

Safety auto shut off

The safety auto shut off system detects any

abnormally high temperatures within the

heater and automatically switches it off to

prevent overheating.

1. Place the heater on a flat level surface

and ensure that the air intake and air

outlet are clear of obstructions.

2. Insert the plug into a 230-240V power

outlet and turn the power on.

3. Move the on/off switch at the rear of the

unit to the on (I) position. A beep will

sound.

4. Press the power button on the control

panel to turn the heater on. The LCD will

display the current room temperature and

HIGH, indicating that it is operating in

HIGH heat mode.

5. Press the MODE button to cycle through

the various operating modes:

LOW – the heater will continuously run at

its low wattage.

AUTO - the digital thermostat will cycle

the heater on and off to maintain your

selected temperature. See instructions on

setting the digital thermostat below.

HIGH - the heater will continuously run at

its high wattage.

6. To turn the heater off, press the power

button on the control panel. The heater

will stop operating.

7. Move the on/off switch at the rear of the

unit to the off position (O). Turn the power

off and remove the plug from the power

outlet when not in use.

Setting the digital thermostat

1. Press the mode button to select AUTO

mode. AUTO will appear on the LCD

screen, and the current room temperature

will flash.

2. Use the Temp + and – buttons to select

the desired temperature setting. SET,

TEMP and the selected temperature will

flash several times to indicate that the

thermostat is set. The LCD will return to

displaying the room temperature.

3. Once the room temperature reaches 3°C

above the selected temperature, the heater

will operate for a further 20 seconds and

then cutout. When the room temperature

drops below the set temperature, the

heater will switch back on. The thermostat

will continue to cycle the heater on and off

to maintain your selected temperature.

4. To view the set temperature, press the

Temp button. The set temperature setting

will flash on the screen.

5. To turn the heater off, press the power

button on the control panel. The heater

will stop operating.

6. Move the on/off switch at the rear of the

unit to the off position (O). Turn the power

off and remove the plug from the power

outlet when not in use.

Using your Oscillating Digital

Ceramic Heater

Fig. 2

Activating the Oscillation function

Press the OSC button on the control panel or

remote to activate the oscillation. The heater

will continue to oscillate from side to side,

distributing warm air around the room, until

the OSC button is pressed again.

The body of the heater will stop oscillating in

its current position. To align the heater body

and base, press the OSC button to activate

the oscillation, and press it again when the

two parts are aligned.

Setting the timer

1. Set the heater to the desired heat or

temperature setting as per the instructions

above.

2. Press the timer button once to set the

heater to switch off after one hour, twice

for 2 hours and so on, up to 8 hours. The

timer icon will appear on the screen, as

shown in figure 3. The heater will continue

operating for the selected number of hours

and will then switch off automatically.

Using the remote control

The buttons on the remote control function

in the same way as the buttons on the

control panel. It is powered by 2 x AAA

batteries.

Note: when using the oscillating function in

AUTO mode the heater will stop oscillating

when the selected temperature is reached

and the unit cycles off. It will resume

oscillating when the heater cycles back on to

maintain the selected temperature level.

Using your Oscillating Digital Ceramic Heater (continued)

AUTO ROOM TEMP

Fig. 3

Your Oscillating Digital Ceramic heater is

equipped with a safety system that detects

any abnormally high temperatures within the

heater and automatically shuts it off to

prevent overheating. Should the safety auto

shut off activate and switch the heater off, it

will need to be reset.

To reset the heater:

1. Move the on/off switch at the rear of the

heater to the off position (O).

2. Unplug the heater and wait 5-10 minutes

for the unit to cool down.

3. After 5-10 minutes, plug the heater in

again and operate as usual.

Resetting the safety auto shut off

Ensure that the heater is switched off and

disconnected from the power outlet before

cleaning.

Carefully wipe the exterior of the heater with

a soft damp cloth and dry thoroughly with a

dry cloth.

Over timer dust may accumulate on the front

vent of the heater, this can be removed by

wiping with a damp cloth, or carefully going

across the vent with a vacuum cleaner with

brush attachment.

Do not use harsh or abrasive cleaners to

clean your heater, as these will damage the

surface.

Care and cleaning

Inhaltsverzeichnis

Andere Sunbeam Heizung Handbücher

Sunbeam

Sunbeam SCH4062 Bedienungsanleitung

Sunbeam

Sunbeam HE4100 Bedienungsanleitung

Sunbeam

Sunbeam SCH4062 Bedienungsanleitung

Sunbeam

Sunbeam HE3100 Bedienungsanleitung

Sunbeam

Sunbeam Calefactor Bedienungsanleitung

Sunbeam

Sunbeam SFH436-UM Handbuch

Sunbeam

Sunbeam SFH436-CN Handbuch

Sunbeam

Sunbeam SEH8001 Handbuch

Sunbeam

Sunbeam SCH4062 Handbuch

Sunbeam

Sunbeam SFH111 Bedienungsanleitung

Sunbeam

Sunbeam Micro Furnace MF2000 Bedienungsanleitung

Sunbeam

Sunbeam Smartheat HE6100 Bedienungsanleitung

Sunbeam

Sunbeam Heater Calefactor Bedienungsanleitung

Sunbeam

Sunbeam Tower Fan Heater Bedienungsanleitung

Sunbeam

Sunbeam SFH431-UM Bedienungsanleitung

Sunbeam

Sunbeam SCH160-CN Handbuch

Sunbeam

Sunbeam SCH4015 Series Bedienungsanleitung

Sunbeam

Sunbeam SFH5963M Bedienungsanleitung

Sunbeam

Sunbeam 9100020009040 Bedienungsanleitung

Sunbeam

Sunbeam SFH136-CN Handbuch

Sunbeam

Sunbeam HE2055 Bedienungsanleitung

Sunbeam

Sunbeam HE4900 Bedienungsanleitung

Sunbeam

Sunbeam HE2050 Bedienungsanleitung

Sunbeam

Sunbeam SFH442 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung