Sunbeam HE3100 Bedienungsanleitung

Convection Plus Heaters

Instruction Booklet

HE3100 1200W heater with micathermic elements

HE3900 2200W heater with micathermic elements

Please read these instructions carefully

and retain for future reference.

Contents

Important instructions – retain for

future use.

Sunbeam’s Safety Precautions 1

Sunbeam’s Total Safety System 3

Features of your HE3100 Convection Plus Heater 4

Features of your HE3900 Convection Plus Heater 6

Using your Convection Plus Heater – HE3100 8

Using your Convection Plus Heater – HE3900 9

Wall Mounting and Attaching the Wheels 11

Care and Cleaning 12

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

Sunbeam are very safety conscious when

designing and manufacturing consumer products,

but it is essential that the product user also

exercise care when using an electrical appliance.

Listed below are precautions which are essential

for the safe use of an electrical appliance:

• Read carefully and save all the instructions

provided with an appliance.

• Always turn the power off at the power outlet

before you insert or remove a plug. Remove

by grasping the plug – do not pull on the cord.

• Turn the power off and remove the plug

when the appliance is not in use and

before cleaning.

• Do not use your appliance with an extension

cord unless this cord has been checked

and tested by a qualified technician or

service person.

• Always use your appliance from a power

outlet of the voltage (A.C. only) marked

on the appliance.

• This appliance is not intended for use by young

children or infirm persons unless they have

been adequately supervised by a responsible

adult to ensure that they can use the appliance

safely.

• Young children should be supervised to ensure

that they do not play with the appliance.

• Never leave an appliance unattended while

in use.

• Do not use an appliance for any purpose

other than its intended use.

• Do not place an appliance on or near a hot gas

flame, electric element or on a heated oven.

Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang

over the edge of a table or bench top or touch

any hot surface.

• For safety reasons and to avoid maintenance

by unskilled persons, some appliances are

‘sealed’ using tamperproof screws. Such

appliances should always be returned to the

nearest Sunbeam Appointed Service Centre

for adjustment or repair if required.

• Do not operate any electrical appliance with

a damaged cord or after the appliance has

been damaged in any manner. If damage is

suspected, return the appliance to the nearest

Sunbeam Appointed Service Centre

for examination, repair or adjustment.

• For additional protection, Sunbeam

recommend the use of a residual current

device (RCD) with a tripping current not

exceeding 30mA in the electrical circuit

supplying power to your appliances.

• Do not immerse the appliance in water

or any other liquid unless recommended.

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

• This heater becomes hot during use. To avoid

burns, do not let bare skin touch hot surfaces.

If provided, use handles when moving this

heater. Keep combustible materials such as

furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (90cm) away from the

front of the heater and keep them away from

the sides and rear.

• Extreme caution is necessary when any heater

is used by or near children or invalids and

whenever the heater is left unattended.

• Always unplug the heater when not in use.

• Do not use outdoors.

• Do not run the cord of the heater under

carpeting. Do not cover the cord with throw

rugs, runners or other floor coverings. Arrange

the cord away from traffic areas where it will

not be tripped over.

• Do not locate the heater immediately below a

socket outlet.

• Do not use this heater in the immediate

surrounds of a bath, shower, laundry area or

swimming pool.

• Do not insert or allow foreign objects to enter

any ventilation or exhaust openings as this may

cause electric shock or fire, or damage to the

heater.

• To prevent a possible fire, do not block air

intakes or exhaust in any manner. Do not use

on soft surfaces, such as beds, where opening

may become blocked.

• A heater has hot and arcing or sparking parts

inside. Do not use it in areas where petrol,

paint or flammable liquids are used or stored.

• To prevent overheating, do not cover the

heater.

• When turned on for the first time, your

new heater will emit a slight odour for

up to 8 hours. This is due to the initial

heating of the materials used. It is safe, not

detrimental to the performance of the heater

and will not reoccur. Sunbeam advises that

the heater be placed in a well ventilated

area during this period.

Safety auto shut-off

Your Sunbeam Convection Plus Heater is

equipped with a safety system that detects

any abnormally high temperatures within the

heater and automatically cuts power to the

heating element, preventing overheating.

Once the heater has cooled it will

automatically resume normal operation.

Thermal back-up fuse

In addition to this automatic shut-off, your

heater contains a thermal back-up fuse to

provide additional back-up protection. If the

heater is in an overheat situation, the back-

up fuse will open, stopping the power flow

to the heating element. This fuse cannot

be reset, so in the event that the back-up

fuse is activated, the heater will need to be

replaced.

Instant tip-over cut-out

Your Sunbeam Convection Plus Heater is also

equipped with an instant tip over cut-out

switch. This switch automatically interrupts

the power flow to the heating element when

the heater is tilted to a certain angle. If

the heater is tipped over, it will not turn on

until it has been placed back in the upright

position.

Note: The tip over cut-out switch will activate

when the heater is tilted forward, backward

or sideways. Care should be taken to ensure

your heater remains upright at all times.

Sunbeam’s Total Safety System

Double heat micathermic elements

The revolutionary micathermic heating

elements produce both radiant and

convection heat. Instant heat radiates from

the large surface area in one minute, while

natural convection circulates warm air around

the room quickly and evenly.

Wall mountable

The slim design is ideal for wall mounting.

The unique reflective design keeps the rear of

the heater cooler, enabling it to be mounted

directly onto the wall, without the clearance

required by other panel heaters.

Safety auto shut-off

This built-in safety system detects any

abnormally high temperatures within the

heater and automatically switches it off to

prevent overheating.

Handle and wheels

Wheels and a handle at the rear of

the unit allow you to safely move the

heater while in use.

Instant tip over cut-out

The instant tip over cut-out switch

automatically cuts the power flow to the

heating element if the heater is tipped over.

The heater will not resume operation until it

is replaced in the upright position.

Features of your HE3100

Convection Plus Heater

Figure 1

Power ON light

Illuminates to indicate that the

heater is switched on.

Mode dial

Turn the mode dial to select your

desired setting: OFF, LOW (1)

or HIGH (2).

Thermostat indicator light

The red thermostat light indicates

that the heater is warming up to the

selected temperature and will go out

when the selected temperature has

been reached.

Thermostat dial

Turn the thermostat dial clockwise to

select your desired temperature.

Adjustable thermostat

The adjustable thermostat allows you

to set the temperature to your desired

comfort level.

Once the selected heat level is

reached, the heater will automatically

cycle on and off to maintain it.

Dimensions

When the wheels are attached, your

HE3100 Convection Plus heater is

approximately:

(L)620 x (W)245 x (H)510mm

Features of your HE3900

Convection Plus Heater

Double heat micathermic elements

The revolutionary micathermic heating

elements produce both radiant and

convection heat. Instant heat radiates from

the large surface area in one minute, while

natural convection circulates warm air around

the room quickly and evenly.

Safety auto shut-off

This built-in safety system detects any

abnormally high temperatures within the

heater and automatically switches it off to

prevent overheating.

Instant tip over cut-out

The instant tip over cut-out switch

automatically cuts the power flow to the

heating element if the heater is tipped over.

The heater will not resume operation until it

is replaced in the upright position.

Handle and wheels

Wheels and a handle at the rear of

the unit allow you to safely move the

heater while in use.

Wall mountable

The slim design is ideal for wall mounting.

The unique reflective design keeps the rear of

the heater cooler, enabling it to be mounted

directly onto the wall, without the clearance

required by other panel heaters.

Adjustable thermostat

The adjustable thermostat allows you to set

the temperature to your desired comfort level.

Once the selected heat level is reached, the

heater will automatically cycle on and off to

maintain it.

Figure 2

Remote control

The easy to use remote control enables the

heater to be operated from anywhere in the

room.

LED screen

The LED screen displays the current settings

including the ambient room temperature, the

selected mode, or timer setting.

ON/OFF switch

Illuminates to indicate that the heater is

switched on.

Mode button

Press the mode button to select your desired

operating mode: STANDBY, LO, HI or AUTO.

Select the AUTO mode when setting the

digital thermostat.

Timer button

The timer button allows you to program the

heater to automatically switch on or off after

a desired time period. It can be set to turn

on between 1 and 12 hours or off between

0.5 and 8 hours.

Infrared receiver

Point the remote control towards the infrared

receiver to operate the heater from anywhere

in the room.

Plus/minus arrows

Use the plus/minus arrow buttons when

in AUTO mode to select your desired heat

setting or after pressing the timer button to

select your desired time setting.

Dimensions

When the wheels are attached your

HE3900 Convection Plus heater is

approximately:

(L)850 x (W)245 x (H)600mm

Figure 3

1. Place the heater on a flat level surface and

ensure that the air intake and outlet are

clear of obstructions.

Note: When turned on for the first time,

your new heater will emit a slight odour

for up to 8 hours. This is due to the initial

heating of the materials used. It is safe,

not detrimental to the performance of

the heater and will not reoccur. Sunbeam

advises that the heater be placed in a well

ventilated area during this period.

2. Ensure that the mode dial and thermostat

dial are both in the OFF position.

3. Insert the plug into a 230/240V power

outlet and turn the power on. The power

ON light will illuminate.

4. Move the mode dial to your desired heat

setting, either low heat (1) or high heat

(2).

5. Turn the thermostat dial clockwise until

the red thermostat indicator light turns on,

indicating that the heater is warming to

the selected temperature. This light will go

out when the selected temperature level is

reached.

6. The thermostat is now set and will

automatically maintain the pre-set

temperature level by turning the heater on

and off.

7. To adjust the selected temperature level,

rotate the thermostat dial anti-clockwise to

lower or clockwise to raise the temperature.

8. To turn the heater off, move the mode dial

to the OFF position.

Using your Convection Plus Heater

HE3100 – 1200W heater with micathermic elements

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sunbeam Heizung Handbücher

Sunbeam

Sunbeam SCH4062 Handbuch

Sunbeam

Sunbeam SFH442 Bedienungsanleitung

Sunbeam

Sunbeam MF1500 1500W Bedienungsanleitung

Sunbeam

Sunbeam SCH160 Handbuch

Sunbeam

Sunbeam SEH8001 Handbuch

Sunbeam

Sunbeam SCH4062 Bedienungsanleitung

Sunbeam

Sunbeam HE2105 Bedienungsanleitung

Sunbeam

Sunbeam Calefactor SFH612 Bedienungsanleitung

Sunbeam

Sunbeam SCH4015 Series Bedienungsanleitung

Sunbeam

Sunbeam Micro Furnace MF2000 Bedienungsanleitung

Sunbeam

Sunbeam HE4900 Bedienungsanleitung

Sunbeam

Sunbeam HE2100 Bedienungsanleitung

Sunbeam

Sunbeam Heater Calefactor Bedienungsanleitung

Sunbeam

Sunbeam SFH431-UM Bedienungsanleitung

Sunbeam

Sunbeam SFH136-CN Handbuch

Sunbeam

Sunbeam HE2050 Bedienungsanleitung

Sunbeam

Sunbeam Smartheat HE6100 Bedienungsanleitung

Sunbeam

Sunbeam Steam Master Bedienungsanleitung

Sunbeam

Sunbeam SFH111 Bedienungsanleitung

Sunbeam

Sunbeam Smartheat HE6150TF Bedienungsanleitung

Sunbeam

Sunbeam SFH436-UM Handbuch

Sunbeam

Sunbeam SFH107 Handbuch

Sunbeam

Sunbeam HE2300 Bedienungsanleitung

Sunbeam

Sunbeam SFH610 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung