Suntor ST5HPT Bedienungsanleitung

1st

ST5/11/30/50HPT User Manual

Contents

I. Disclaimer...............................................................................................................................................................................2nd

II. Precautions for integration...................................................................................................................................................2nd

III. List of in-box items................................................................................................................................................................3rd

IV. Interface................................................................................................................................................................................ 4th

V. Precautions When Powering On............................................................................................................................................4th

VI. Operating Instructions & Steps............................................................................................................................................ 5th

VII. Antenna Installation............................................................................................................................................................ 7th

1. Multi-rotor UAV............................................................................................................................................................. 7th

2. Fixed Wing UAV..............................................................................................................................................................7th

VIII. Software Operation............................................................................................................................................................ 8th

1. Start Connecting Tdd-cofdm equipment....................................................................................................................... 8th

2. Restart TDD-COFDM Control Panel software.............................................................................................................8th

3. RF Configuration method..........................................................................................................................................8th

3. 1. TX Rate..............................................................................................................................................................8th

3.2. Channel Bandwidth............................................................................................................................................ 9th

3.3. Channel-Frequency.............................................................................................................................................9th

3.4. Wireless Distance............................................................................................................................................... 9th

3.5. RX TX Mode:...................................................................................................................................................10th

3.6. TX Power..........................................................................................................................................................10th

4. Seria Configuration method:....................................................................................................................................... 10th

4.1. Data Baud Rate.................................................................................................................................................10th

4.2. Data Format...................................................................................................................................................... 11th

4.3. IP Protocol Config............................................................................................................................................ 11th

5. RS232 Configuration Menu.........................................................................................................................................11th

6. IP New Network Configuration method:.................................................................................................................... 12th

7. RF New NET Configuration method.......................................................................................................................... 12th

7.1. RF Net ID:........................................................................................................................................................ 12th

7.2. RF Encrypt KEY ............................................................................................................................................ 12th

SUNTOR ELECTRONICS CO., LIMITED

V1.0

2nd

I. Disclaimer

SUNTOR is the registered trademark of SUNTOR ELECTRONICS CO., LIMITED. All product names and brands

in this manual are trademarks or registered trademarks of the Company. SUNTOR ELECTRONICS CO.,

LIMITED. reserves all copyrights of the product and the manual. All the information must not be copied or

reproduced in any form without permission of the Company. There may be semantic differences between

disclaimers of different languages. The Chinese version shall prevail in Chinese mainland, while the English

version shall prevail in other regions. Thank you for purchasing SUNTOR ST5/11/30HPT. Please use

ST5/11/30HPT according to local radio regulations. Before use, carefully read this disclaimer. Once the

product is used, all the contents of the disclaimer will be regarded recognized and accepted. Please install

and operate the product in strict accordance with the requirements of this manual. SUNTOR ELECTRONICS

CO., LIMITED and its affiliates will not assume any legal responsibility for results or losses caused by

improper use, installation, assembly and modification (including the use of non-specified SUNTOR parts

and accessories, such as the radio power amplifier, antenna and SMA extension cord).

Notes: Improper operation of ST5/11/30HPT may cause personal injury or damage to properties to some

extent. Pay attention to operation safety.

II. Precautions for integration

1. Be sure to use the parts provided by SUNTOR.

2. Please not reverse connect power line positive and negative. Or the device will be burn out.

3. Install the antenna before power on. Please not install or remove the antenna with power.

4. Given that the carbon fiber body and metal load may have shielding effects on antenna signals, they

should not be installed between the antenna and ground terminal. Keep the antenna of the on board

terminal free from winding or blocking by obstacles. The antenna end should be vertically downward

without bending, to prevent shortening of the communication distance and failure in communication

as a result of blocking.

5. The antennas of the onboard terminal should be separated from each other to achieve good

anti-jamming effects. It should be kept far away from antennas of other onboard radio transmitters, as

huge electromagnetic noise and interference may be caused between various radio antennas, which

will seriously shorten the communication distance, reduce the reliability of communication and even

cause failure in communication. It is recommended to use the functions of SUNTOR product, i.e. image

transmission and RS232 two-way serial port communication to minimize the quantity of onboard radio

devices.

6. Use the antenna of specified type, and properly install it. It is prohibited to use antennas of other

types.

3rd

7. To directly use the HDMI output of the PTZ camera, connect the PTZ holder after energizing and

self-testing, to avoid damage caused by rotation of the PTZ holder in self-testing to the HDMI cable. To

thoroughly solve this problem, it is preferred to use the split product, that is, the HDMI RX video

encoder board and PTZ camera are integrated with a short distance, and separated from the Ethernet

TX via the 4pin 100Mbps Ethernet cable. In this case, the reliability of HDMI signals between the PTZ

camera and HDMIRX video communication board will be greatly improved.

8. The HDMI cable and antenna may cause interference to GPS. They should be kept far away from the

GPS module and its cables as much as possible in the wiring process.

9. Do not disassemble or modify SUNTOR ST5/11/30HPT. Any problem during installation, contact

SUNTOR or the sales agent.

10. Keep appropriate distances between electronic devices during installation to minimize electromagnetic

interference.

III. List of in-box items

On board x1

Ground terminal x1

On board antenna x1

Ground antenna x1

4P-to-DC power cable x2

HDMI video cable x1

Network cable x1

TTL Serial port cable x2

USB cable of TTL serial port x1

4th

TPalyer Key

USB 2.0 Key

IV. Interface

Remark: The TX and RX have same interface specifications, All references are given above.

V. Precautions When Powering On

1. Before using, make sure that all cables are secure and reliably and all components can work properly.

2. After starting the product, check it for proper operation by observing whether the self-test indicator of

ST-3500HDis continuously ON for 30s and then flicker and whether the image of the camera is shown

on the ground terminal.

5th

3. Check the surrounding environment for to ensure there is no other 2.4GHz devices to cause

interference. If use the Futaba remote controller, the controller should be adjusted into the French

mode. Otherwise, the video transmission performance of ST5/11/30HPT may be serious affected and

also the Futaba transceiver may be in the abnormal status and accidents may be caused.

4. Remark: How to adjust the Futaba controller into French mode:

[LINKAGE MENU]→FRQUENCY→ RTN b→ [AREA]→[FRANCE]

5. Before use, check the electric quantity of the ground terminal. If the ground terminal is OFF, the

built-in radio receiver of the onboard terminal will be out-of-control.

6. Pay attention to the angle and direction of the antenna of the ground terminal during flight. In case of

poor signal or image quality, adjusting the inclination of the antenna of the ground terminal can

improve the signal or image effect.

7. The camera should be fully charged to ensure normal video output.

8. ST5/11/30HPT has the functions of two-way communication of image data and serial port data. If the

transmitted ground image is stuck or stopped for more than 10s but less than 30s, it means that the

radio channel signal is weakened or the radio channel is narrowed. In this case, the aircraft must not fly

farther away from the ground. In order to ensure the normal communication of serial data and the

safety of the aircraft, the distance between the aircraft and ground terminal should be immediately

shortened. Otherwise, the built-in radio receiver of the onboard terminal will be out-of-control.

9. 8. If required, purchase electronic devices (such as HD displays, Network cables, etc.) with good

electromagnetic shielding effects.

VI. Operating Instructions & Steps

1. Make TX and RX and accessories ready.

Besides the whole equipment we supply, you need to

also make sure the video source, display and power

ready before operating.

6th

2. Connection

3. Power on

After checking all the connections are in good condition, turn on the the video

source, LCD display, transmitter and receiver. The PWR indicator will bright and

the whole system start.

4. The status of all indicators during starting

When the device begin to normally start and work, all indicators status is described as follow:

1After power on, light 1,2,3 turn green, light 6 turns blue.

2After few seconds, light 1,2,3,6 start flashing.

And light 5 green is normally on.

3After a few seconds, the starting is complete.

Light 1(Green), 2(Green), 3(Green), 6(blue), 4(Red) are

normally on. Light 5 will fast blink.

4When data transmission goes well, WL green

light will flicker.

Remark：Light1, 2, 3 are indicator for signal strength.

1Light 1 on: Signal Weak

2Light 1,2 on: Signal Normal

3Light 1,2,3 on: Signal Strong

4When green light 1,2,3 repeatedly flash in sequence: No connection. The connection between TX and RX is failed

5Light 4 is Data connection light. If light 4 not bright, which means no data connection.

6When the transmission is normal, the WL light will normal on.

7After the receiver powered, the”POWER ON” letters will be showed on the display bottom right corner

5. Boot up successfully

7th

After successfully connection, the display will smoothly show the image.

Remark: In UAV application, please make the connection successfully then fly the UAV. About the right way of

installation antenna please refer to the following description.

VII. Antenna Installation

1. Multi-rotor UAV

1) To select the original antenna and the SMA metal shielded semi-flexible blue feeder cable provided by

SUNTOR. The feeder cable is used to connect the TX SMA port and the antenna.

2) The antenna needs to be mounted vertically downwards, and it

is not recommended to mount it vertically at the top of the UAV.

3) The best installation location is the UAV ground bracket. With

the antenna inside the bracket can only use fiberglass material.

4) If the ground bracket is automatically retracted, the antenna can

be installed in the lower part of the aircraft, and the ground RX

antenna is recommended to use same antenna with TX( 29cm

length antenna).

5) If the antenna is intercepted by the camera or pod or the loudspeaker, the video on RX will appear

image stuck or mosaic and It is recommended to immediately adjust the flight attitude and angle.

2. Fixed Wing UAV

1) To select the original antenna and the SMA metal shielded semi-flexible blue feeder cable provided by

SUNTOR. The feeder cable is used to connect the TX SMA port and the antenna.

2) The antenna needs to be mounted vertically downwards, and it is not recommended to mount it

SMA Feeder Cable

8th

vertically at the top of the UAV.

3) It is recommended to use 29cm long antenna. The best installation position is the center of the UAV tail,

prominent outside the body and vertical downward.

4) The second optional mounting position is located below the wing and body joints, vertical down, as far

as possible away from the wing but near the machine abdomen, protruding below the abdomen level.

VIII. Software Operation

1. Start Connecting Tdd-cofdm equipment

First, enter the IP address，Next click Connect TDD button.

2. Restart TDD-COFDM Control Panel software:click Restart TDD button.

3. RF Configuration method

3. 1. TX Rate（Default：QPSK FEC 1/2）:

This setting determines the modulation type and in turn the rate at which the data is to be

wirelessly transferred. The default and recommended setting for both Master and Slave

units is ‘Auto’. When in ‘Auto’ the unit will transfer data at the highest possible rate in

consideration of the receive signal strength (RSSI).

Refer to Performance for a table breakdown of performance at selected rates. If setting a

fixed TX Rate It is recommended to retain a fade margin of at least 10 dbm for optimum

9th

performance. For example, for a link (8MHz channel) with a signal strength of at least –75dBm, a TX rate of 16-QAM 3/4

FEC is recommended. Setting to the highest rate with a poor link may result in reduced performance.

3.2. Channel Bandwidth（Default：4Mhz）:

Select the channel bandwidth from the list. Refer to the specifications to see

the relationship and performance between channel band, width,throughput

and sensitivity.Generally a larger channel has greater throughput, at the cost of

sensitivity, while a smaller channel tends to be more robust, but at the cost of

throughput.

3.3. Channel-Frequency（Default：2479Mhz）:

2402 - 2482 (1MHz BW, CH 1-81)

2402 - 2482 (2MHz BW, CH 1-81)

2405 - 2479 (4MHz BW, CH 4-78)

2407 - 2477 (8MHz BW, CH 6-76)

3.4. Wireless Distance（Default：10km）:

The Wireless Distance parameter allows a user to set the expected distance the

wireless signal needs to travel. The TDD-COFDM sets various internal timeouts to

account for this travel time. Longer distances will require a higher setting, and

shorter distances may perform better if the setting is reduced.

10th

3.5. RX TX Mode:

TX Master - A Master may provide a wireless data connection to many slaves

RX Slave- A Salve may sustain one wireless connection,i.e. to an Master.

3.6. TX Power（Default：30dbm）:

This setting establishes the transmit power level which will be presented to the

antenna connector of the TDD_COFDM.Unless required, the Tx Power should be

set not for maximum, but rather for the minimum value required to maintain an

adequate system fade margin.

4. Seria Configuration method:

4.1. Data Baud Rate（Default：115200）:

The serial baud rate is the rate at which the modem is to communicate with the

attached local asynchronous device.

921600/460800/230400/115200/57600/38400/28800/19200/14400/9600/7200/4

800/3600/2400/1200/600/300.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Suntor Empfänger Handbücher

Suntor

Suntor ST5NPT Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung