Supermicro AS-2123BT-HNR Betriebsanleitung

Information for Lot 9 of ErP (Ecodesign)

This addendum addresses European Union (EU) Ecodesign requirements for servers and storage

products. All data and ratings within this addendum are in reference only to the Supermicro product(s) in

the manual. The below information conforms to requirements laid down in Annex II of the Commission

Regulation 2019/424.

3(1)(a): See Section 1.1 of the system manual for the product type.

3(1)(b): See the title page and preface of the system manual for the trademark and

manufacturer’s address.

3(1)(c): See the title page of the system manual for product model number(s).

3(1)(d): See the serial number on the physical system to determine the year of manufacture.

3(1)(e-j): PSU Efficiency and Power Factor Value (Table) (From 80 Plus report)

PSU Model #: PWS-

2K60A-1R

Watts: 2600W

PSU Efficiency

Power Factor

% of Rated Load

10 % 20 % 50 % 100 %

50 %

Single Output (AC-DC)

90.42

95.83

96.22

94.37

0.99

Multiple Output (AC-DC)

N/A

System (EUT) Efficiency in Idle State Power (Table)

Representative

Configurations

Total Measured Idle

State Power (W)

Calculated Idle Power

Allowance per Node (W)

High-End Performance

Configuration

961.7

1519.9

Typical Configuration

Low-End Performance

Configuration

599.8

881.5

System (EUT) Efficiency in Active State Power (Table)

Representative

Configurations

Active State

Efficiency Score

(Effserver)

Minimum Active State

Efficiency for 2-Socket

Server

High-End Performance

Configuration

40.1

Typical Configuration

8.0

Low-End Performance

Configuration

38.4

3(1)(k): The operating condition class is A2.

Dry bulb temp °C

Humidity range, non-condensing

Operati

conditi

Allowab

range

Reco

m

mend

Allowable range

Recommended

range

Max

dew

point (°

Maximu

m rate

change

15- 32

18-27

–

12 °C Dew Point (DP)

and

8 % relative

humidity (RH) to

17 °C DP and 80 % RH

–

9 °C DP to

15 °C DP

and

60 %

5/20

10-35

18-27

–

12 °C DP and 8 % RH

21 °C DP and 80 %

Same as A1

5/20

5-40

18-27

–

12 °C DP and 8 % RH

24 °C DP and 85 %

Same as A1

5/20

5-45

18-27

–

12 °C DP and 8 % RH

24 °C DP and 90 %

Same as A1

5/20

3(1)(l): The idle state power at the higher boundary temperature of the operating conditions

class is 1135W.

3(1)(m): The active state efficiency and performance is 40.1.

3(1)(n): There are two methods by which a user can securely delete data from this system. The

user performing secure data deletion should be an IT professional.

The first is with a Unified Extensible Firmware Interface (UEFI) shell utility. This utility

works on X10/X11/H11/H12/M11 motherboard series with onboard SATA/NVMe devices.

Any user may access and download this utility through following link:

https://www.supermicro.com/about/policies/disclaimer.cfm?url=/wftp/utility/Lot9_Secure

_Data_Deletion_Utility/

Download the shell utility package and extract it to a USB flash drive, then plug the drive

into the server for which secure data deletion is necessary. Then turn the system on.

Navigate to the BIOS setup menu, then place the server system into the UEFI shell

environment. Follow the instructions in the README file to invoke the utility and

complete the deletion.

The second method is through the secure data deletion tool provided by the original

manufacturer of the hard drive. This should be used in a scenario where the shell utility

is not applicable. Each manufacturer should have the tool available on their website. If

needed, please look on the hard drive label for the name of the manufacturer and model

information.

3(1)(o): List of recommended combinations of blade servers with chassis: N/A.

3(1)(p): List of all current SKUs within this product family: AS -2123BT-HNR.

3(3)(a): There is no use of cobalt in batteries in this product.

The indicative weight range of neodymium in the HDD is 0.0 if manufactured by Western

Digital, and is between 5-25 grams if manufactured by Seagate.

3(3)(b): Please see the disassembly instructions on the next page.

Illustrated System Disassembly Instructions

Please note:

All the illustrations in the below disassembly instructions are for demonstration only.

Components shown here may not match exactly with the components in your system.

CAUTION: Always power off the system and unplug the power cord(s) first

before disassembling the system!

1. Data Storage Devices

Type and number of fastenings:

One (1) latch and four (4) Phillips screws per drive.

Tools required:

Screwdriver with PH2 bit.

Procedure:

1. Press the release button on the drive tray. This extends the drive bay handle.

2. Use the handle to pull the drive out of the chassis.

3. Remove the four screws on the drive tray to release the hard drive (dummy tray shown in

illustration).

2. Memory

Type and number of fastenings:

Two (2) latches per memory module.

Tools required:

None.

Procedure:

1. Press both release tabs on the ends of the memory module to unlock it.

2. Once the module is loosened, remove it from the memory slot.

3. Processor

Type and number of fastenings:

Four (4) T20 Torx screws.

Tools required:

Screwdriver with T20 Torx bit.

Procedure:

Remove the screws in the sequence of 4, then 3, then 2, then 1, as marked in the

illustration below. After removing the screws, lift the processor heatsink module off the processor

socket. Unscrew the processor socket frame in the sequence of 3, 2, and then 1. Flip the socket

frame up. Lift up the rail frame and slide the processor out.

4. Riser Card

Type and number of fastenings:

Five (5) Phillips screws.

Tools required:

Screwdriver with PH2 bit.

Procedure:

1. Remove the node from the chassis by pulling on the pulling ears.

2. Remove the screw at the center of the bracket.

3. Remove the two screws securing each riser card.

4. Lift the riser card out from the motherboard expansion slot.

5. Expansion Card

Type and number of fastenings:

One (1) Phillips screw.

Tools required:

Screwdriver with PH2 bit.

Procedure:

1. Remove the screw holding the add-on card in place.

2. Carefully pull the add-on card out from the riser card.

6. Power Supply Module

Type and number of fastenings:

One (1) latch per module.

Tools required:

None.

Procedure:

1. Unplug the power cord from the power supply.

2. Push the release tab on the back of the power supply module to the side and pull the module

straight out.

7. Chassis Cover

Type and number of fastenings:

Two (2) Phillips screw

Tools required:

Screwdriver with PH2 bit.

Procedure:

1. Remove the two screws that secure the top cover onto the chassis.

2. Lift the top cover up and off the chassis.

8. Batteries

Type and number of fastenings:

One (1) latch.

Tools required:

None.

Procedure:

Push aside the small clamp that covers the edge of the battery. When the battery is

released, lift it out of the holder.

Inhaltsverzeichnis

Andere Supermicro Server Handbücher

Supermicro

Supermicro SuperServer E300-9A-4CN8 Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 5018A-LTN4 Bedienungsanleitung

Supermicro

Supermicro A+ AS -2114GT-DNR Bedienungsanleitung

Supermicro

Supermicro AS -4125GS-TNRT Bedienungsanleitung

Supermicro

Supermicro MicroBlade MBE-628L-416 Bedienungsanleitung

Supermicro

Supermicro SuperServer 2028R-C1R Bedienungsanleitung

Supermicro

Supermicro SuperServer 2028GR-TR Bedienungsanleitung

Supermicro

Supermicro SuperServer E50-9AP-L Bedienungsanleitung

Supermicro

Supermicro SuperServer 5029C-T Bedienungsanleitung

Supermicro

Supermicro A+ Server AS-2115GT-HNTR Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-121C-TN2R Bedienungsanleitung

Supermicro

Supermicro SuperServer 2049U-TR4 Bedienungsanleitung

Supermicro

Supermicro 7044H-32R Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 5015P-8R Bedienungsanleitung

Supermicro

Supermicro A+ AS-1114S-WN10RT Bedienungsanleitung

Supermicro

Supermicro SuperServer 6027TR-DTRF+ Bedienungsanleitung

Supermicro

Supermicro SuperServer 1029P-N32R Bedienungsanleitung

Supermicro

Supermicro X13SRA-TF Bedienungsanleitung

Supermicro

Supermicro SuperServer 6011D Bedienungsanleitung

Supermicro

Supermicro SuperServer 610U-TNR Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-110P-FRN2T Bedienungsanleitung

Supermicro

Supermicro AS-1115HS-TNR Bedienungsanleitung

Supermicro

Supermicro SuperStorage SSG-6049SP-DE2CR60 Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6034H-X8R Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung