Supermicro SBA-7121M-T1 Handbuch

SBA-7121M-T1 Blade Module

RAID Setup Procedure

Revison 1.0

SBA-7121M-T1 Blade Module RAID Setup Procedure

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The

vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no

commitment to update or to keep current the information in this manual, or to notify any person or

organization of the updates. Please Note: For the most up-to-date version of this manual, please see

our web site at www.supermicro.com.

Super Micro Computer, Inc. (“Supermicro”) reserves the right to make changes to the product described

in this manual at any time and without notice. This product, including software, if any, and documentation

may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or

machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE

THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE,

SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF

REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE,

SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara

County in the State of California, USA.. The State of California, County of Santa Clara shall be the

exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not

exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the manufacturer’s instruction manual, may cause harmful interference with radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference,

in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning

applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further

details.

Manual Revison 1.0

Release Date: March 31, 2008

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy

any part of this document.

Information in this document is subject to change without notice. Other products and companies referred

to herein are trademarks or registered trademarks of their respective companies or mark holders.

Printed in the United States of America

WARNING: HANDLING OF LEAD SOLDER MATERIALS USED IN THIS

PRODUCT MAY EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE

STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER

REPRODUCTIVE HARM.

SBA-7121M-T1

RAID Setup Procedure

1. Installing the Operating System

An operating system (OS) must be installed on each blade module. Unlike most blade

systems, blades with Microsoft Windows OS and blades with Linux OS can both occupy

and operate within the same blade enclosure. Refer to the Supermicro web site for a

complete list of supported operating systems.

There are several methods of installing an OS to the blade modules.

Installing with an External USB CD-ROM Drive

The most common method of installing the OS is with an external USB CD-ROM drive.

Take the following steps to install the OS to a blade module:

1. Connect an SUV cable (Serial port/USB port/Video port cable) to the KVM

connector on the front of the blade module. You will then need to attach a USB hub

to the USB port on this cable to provide multiple USB ports.

2. Connect the external CD-ROM drive, a USB keyboard and a mouse to the USB hub.

You will also need to connect a monitor to the video connector on the SUV cable.

Turn on the blade module.

3. Insert the CD containing the OS into the CD-ROM drive.

4. Follow the prompts to begin the installation.

Installing via PXE Boot

PXE (Preboot Execution Environment) is used to boot a computer over a network. To

install the OS via PXE, the following conditions must be met:

1. The PXE BOOT option in BIOS must be enabled.

2. A PXE server has been configured (this can be another blade in the system).

3. The PXE server must be connected over a network to the blade to be booted.

4. The blade has only non-partitioned/unformatted hard drives installed and no

bootable devices attached to it.

Once these conditions are met, make sure the PXE server is running then turn on the

blade you wish to boot and/or install the OS to. The BIOS in the blade will look at all

WARNING: Installing the OS from an external CD-ROM drive may take several

hours to complete.

SBA-7121M-T1 RAID Setup Procedure

bootable devices and finding none will connect to the PXE server to begin the boot/

install.

Installing via Virtual Media (Drive Redirection)

You can install the OS via Virtual Media through either the IPMI or the Web-based

Management utility. With this method, the OS is installed from an ISO image that resides

on another system/blade. Refer to the appropriate Appendix in the SuperBlade User’s

Guide for the Virtual Media (CD-ROM or Drive Redirection) sections in either of the two

utility programs.

2. Management Software

System management may be performed with either of two software packages: IPMI or a

Web-based Management utility. Both are designed to provide an administrator with a

comprehensive set of functions and monitored data to keep tabs on the system and

perform management activites.

Refer to Chapter 8, SuperBlade User’s Guide for details on the various functions

provided by these management programs.

7-1 Installing the Operating System with RAID

Any blade module that supports two or more hard drives may be used to create a RAID

RAID array. For AMD processor SuperBlade modules, only the SBA-7121M-T1 blade

module with two hard drives installed works for this purpose.

Preparing for Setup

Before you begin the installation, verify the following:

1. The blade module has two or more hard drives installed.

2. These drives must not have an OS installed and must be non-partitioned (formatted

is ok).

3. The installation procedure is done via KVM, so have a KVM cable (CBL-0218L)

connected to the KVM connector on the blade module with a keyboard, mouse and

monitor attached.

Changing BIOS Settings for RAID Configuration

1. Boot the blade and hit the <DELETE> key to enter the BIOS setup utility.

2. In the ADVANCED SETTINGS Menu, highlight the SATA CONFIGURATION option and hit

<ENTER>.

NOTE: You may also instead use IPMI or the Web-based Management utility to

access the blade.

SBA-7121M-T1 RAID Setup Procedure

3. From the SATA Configuration menu screen select the NVIDIA RAID FUNCTION

setting, hit <ENTER> to open its options and select ENABLE.

4. Go to the EXIT Menu, highlight SAVE CHANGES AND EXIT and hit <ENTER>.

Configuring RAID in the Media Shield BIOS Utility

1. After exiting the BIOS utility, the blade will begin to boot up. At this time press

<F10>. This brings up the MEDIA SHIELD BIOS UTILITY screen.

2. In the MEDIA SHIELD BIOS UTILITY screen, select either MIRRORED or STRIPED as

your selection for the RAID MODE option.

3. For the DISKS selection, use the arrow keys to add drives to the ARRAY section. You

must select and add at least two drives to the ARRAY section for RAID to work on the

module.

4. Press <F7> to finish.

5. In the confirm message screen that appears press <Y> to confirm your selections.

6. Another confirm screen will appear asking you if you want to “Clear MBR”. Press

<Y> again to confirm this message.

7. Press <CTRL> + <X> to exit the program.

SBA-7121M-T1 RAID Setup Procedure

Notes

Andere Handbücher für SBA-7121M-T1

Inhaltsverzeichnis

Andere Supermicro Server Handbücher

Supermicro

Supermicro SUPERSERVER 6011H Bedienungsanleitung

Supermicro

Supermicro SuperServer 1029P-N32R Bedienungsanleitung

Supermicro

Supermicro SUPER SUPERSERVER 2028U Series Bedienungsanleitung

Supermicro

Supermicro A+ Server AS -3015MR-H8TNR Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6038R-TXR Bedienungsanleitung

Supermicro

Supermicro SC504-203B Bedienungsanleitung

Supermicro

Supermicro A+ Server AS-2015CS-TNR Bedienungsanleitung

Supermicro

Supermicro 7043P-8R Bedienungsanleitung

Supermicro

Supermicro SuperServer E300-9A-4CN10P Bedienungsanleitung

Supermicro

Supermicro AS-1023US-TR4 Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-2029U-MTNRV Bedienungsanleitung

Supermicro

Supermicro SuperServer 6029U-TR25M Bedienungsanleitung

Supermicro

Supermicro A+ Server AS -1015CS-TNR Bedienungsanleitung

Supermicro

Supermicro Supero SUPERSERVER 5013G-6 Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-620U-TNR Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-120TP-DTTR Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 5018A-MHN4 Bedienungsanleitung

Supermicro

Supermicro SuperServer 5019C-M4L Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-110P-WR Bedienungsanleitung

Supermicro

Supermicro 8025C-3R Bedienungsanleitung

Supermicro

Supermicro SBA-7141A-T Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6013P-i Bedienungsanleitung

Supermicro

Supermicro SuperStorage Server 2028R-NR48N Bedienungsanleitung

Supermicro

Supermicro A+ Server AS-2115GT-HNTR Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung