Swann SwannSecure Bedienungsanleitung

SwannSecure

EN INSTRUCTION MANUAL

Important Information

FCC Verification

This equipment has been tested and found to comply with the limits for

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio

or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

• These devices may not cause harmful interference, and

• These devices must accept any interference received, including in-

terference that may cause undesired operation

Important Note: All jurisdictions have specific laws and regulations re-

lating to the use of cameras. Before using any camera for any purpose,

it is the buyer’s responsibility to be aware of all applicable laws and reg-

ulations that prohibit or limit the use of cameras and to comply with the

applicable laws and regulations.

FCC Regulation (for USA): Prohibition against eavesdropping

Except for the operations of law enforcement officers conducted under

lawful authority, no person shall use, either directly or indirectly, a de-

vice operated pursuant to the provisions of this Part for the purpose

of overhearing or recording the private conversations of others unless

such use is authorized by all of the parties engaging in the conversation.

FCC Warning: The transmitter must not be co-located or operated in con-

junction with any other antenna or transmitter. This equipment complies

with the FCC RF radiation exposure limits set forth for an uncontrolled envi-

ronment. This equipment should be installed and operated with a minimum-

distance of 20cm between the radiator and any part of your body.

Warning: Changes or modifications made to this device not approved

expressly by the party responsible for compliance could void the user’s

authority to operate the equipment.

Important Safety Instructions

• Make sure product is fixed correctly and stable if fastened in place

• Do not operate if wires and terminals are exposed

• Do not cover vents on the back of the device and allow adequate

space for ventilation

Default Password Information

To ensure your privacy, this device supports password protection.

The default, all-access username is admin, the default password is

12345.

To ensure your ongoing privacy, we strongly recommend setting a pass-

word as soon as possible. Choose something that you’ll remember, but

that others would be unlikely to guess.

Contents

Important Information 2

Contents 3

Recording: Encode 4

Recording: Schedule 5

Search: Playback 6

Network: General 7

Network Advanced 8

Alarm: Motion Detection & Sensitivity 9

Alarm: Schedule 10

System: Maintenance & System Information 11

SwannView Link: Local Settings 12

Warranty Information 16

Helpdesk / Technical Support 17

Recording: Encode

The Recording: Encode menu allows you to alter and

customize how the device records footage and encodes

the files.

Encoding is a term which refers to the compression al-

gorithm (a fancy computer term for “make the file small-

er while retaining visual quality”) used by the device.

You can choose and alter:

• The frame rate (how many images per second the de-

vice records)

• The bit rate of each video stream. The higher the data

rate, the “better” your images will look, but the more

space they’ll require on your memory card

Camera No: The channel feed you want to alter the settings for.

Camera Name: You can edit the name of the camera.

Encoding Parameters: Whether you’re editing the parameters for the

mainstream or the substream.

Main-Stream: The main-stream is the video feed that the device will

record and display. This is the higher-quality stream.

Sub-Stream: The sub-stream is the video stream that the device will

send to remote devices via a network or the Internet. It is the low-

er-quality stream as a reduction in video size makes it easier to send

over a network.

Record Audio: This is enabled by default.

Resolution: The resolution cannot be changed.

Frame Rate: The number of frames per second (fps) that the device will

record. The default (and maximum) is referred to as “real-time” and is

15fps. Reducing the number of frames per second will not save on stor-

age space but potentially will improve the data-rate per frame (depend-

ing how you set the bit-rate - see the next point).

Remember that your FPS count is the same as saying “take X photo-

graph per second” (where X is your FPS setting). 6fps doesn’t sound like

much, but it’s still six individual photographs per second. If maintain-

ing image clarity while reducing storage consumption is your priority, it

makes sense to lower the frame rate.

Max. BitRate(Kbps): The actual amount of data that the device will use

to record video. The higher the bitrate, the more space each recording

will take. Generally speaking, recordings encoded at higher bitrates will

be of better quality, especially when recording movement.

The main-stream uses a variable bitrate to record video - the more

movement occurs in the video, the higher the bitrate will have to be.

When there’s little movement in view, the device will automatically re-

duce the bitrate to conserve space.

The sub-stream uses a constant bit-rate. This makes the video easier to

stream over a network or the Internet.

Tap APPLY to save settings.

Recording: Schedule

The schedule presented on-screen applies to one channel only over one

whole week. Use the Copy To function to quickly assign identical sched-

ule layouts to multiple channels at once.

Be careful when programming your schedule. It’s one of the most im-

portant aspects of setting up your device, and if it’s wrong in any way, it

could lead to disastrous complications later.

Copy To: Located at the base of the screen, with Default on one side and

Apply on the other. This will allow you to copy the schedule from the

channel you’re editing to another channel or channels.

Note: The Action Options for Motion Detection will affect the way the

schedule works. By default, all channels are armed to use Motion De-

tection as their recording mode.

Any adjustments in the Alarm menu will change the device’s behaviour,

even if it is set to Motion Recording mode.

There are three types of recording to choose from -

Normal: The device will constantly record for any period where Normal

is selected. You won’t miss anything, but constant recording will fill your

memory card very quickly. Typically, we suggest Motion as a better re-

cording mode for most users.

Motion: The default and recommended recording setting. The device

will only record when it detects something moving in front of a camera,

and will then only record footage from the camera(s) that do detect mo-

tion unless you alter your Action settings.

None: As the name suggests, the device will not record anything.

Tap APPLY to save settings.

Search: Playback

1. Select one or more channels you’d like to playback.

2. From the Video Type menu, select the type(s) of video you’d like to

playback. The options are Manual, Schedule, Motion and All.

3. Set your Start Date/Time and your End Date/Time.

4. Select Search.

5. To initiate playback, select Play.

The playback interface is quite similar to a computer’s media player, or

to the on-screen display of a DVD/Blu-ray player. Most of the controls

are quite straight forward, and operate in the same way as a standard

media player.

Current Position: A basic progress meter. You can click to move the

current position icon to quickly scan through video events.

Rewind: Reverses the footage.

Play / Pause: Plays footage at normal speed. Tap to pause.

Fast-Forward: Speeds up playback.

Network: General

Network Access: Here you can choose between the three different types

of networks that the device can be connected to. The two available are -

DHCP (Dynamic Host Configuration Protocol): Is a system where one

device on your network (usually a router) will automatically assign IP

addresses to devices connected to the network.

Static: Static networks require all devices to have their IP addresses

manually defined, as there is no device dedicated to automatically as-

signing addresses.

IP Address: Just as houses and businesses need to have an address

which identifies their location on the road network, so too do computers

and other devices need addresses to identify their position on the elec-

tronic network. The device uses IPv4 addressing, which consists of four

groups of numbers between 0 and 255, separated by periods. For exam-

ple, a typical IP address might be “192.168.1.24” or something similar.

The most important thing when setting the IP address is that nothing

else on your network shares that IP address.

Subnet Mask: If the IP address is like a street address, then a sub net-

work is like your neighbourhood. This will be formatted in a similar way

to the IP address (e.g. four numbers up to 255 separated by periods) but

contain very different numbers. In the above example, the Subnet Mask

might be something like “255.255.255.0”.

Default Gateway: This is the address of the “way to the Internet” - to

continue the road analogy, this is like your local access point to the high-

way. This is an IP address in the same format as the others, and is typ-

ically very similar to the IP address of the device. To continue the above

examples, it might be something such as “192.168.1.254”.

Preferred DNS Server: Everything on the Internet is located via an IP

address - however, for ease of use, we associate domain names with

those IP addresses.

Alternate DNS Server: A backup DNS server. This is here as a redun-

dancy; your device will probably work without one.

Tap APPLY to save settings.

Network: Advanced

Email Settings: This section has been covered in the quick start guide.

Server Port: This is the port that the device will use to send information

through. You’ll need to enable UPnP on your router so your router can

selectively open these ports, allowing the device to communicate via the

Internet.

HTTP Port: This is the port through which you will be able to log in to

the device.

UPnP Enable: This is enabled by default.

Tap APPLY to save settings.

WiFi Settings: This section has been covered in the quick start guide.

Many of the following networking settings are not required when using SwannLink P2P for remote access.

Alarm: Motion Detection & Sensitivity

The way that the device looks for motion is quite straight forward - it’s a

process where it compares one frame with the next. A certain amount of

“difference” between these two “frames” is interpreted as motion. As a

result, the device is able to detect when there is a change in the picture.

However, this does not necessarily need to be something moving in the

frame. For example, a light being turned on or off, a lightning flash or

even the sun coming out momentarily on a cloudy day might be enough

to trigger the motion detection. However, as these events last only a

moment (and are relatively rare) they will only create a few very short

redundant clips, which will not take up too much space or pose a prob-

lem with scanning through footage.

Channel: Select the camera that you would like to alter.

Motion Detection: Tap the Set button to setup the motion detection area

for that channel. You will see a grid of red boxes. The outlined boxes

mark the area that is sensitive to motion. The area without the red out-

lines is not sensitive to motion. Tap and drag to select the area you want

to select or de-select.

Sensitivity: The Sensitivity setting is controlled by a slider, allowing you

to set a value between 0 and 50. The lower the number, the more sensi-

tive the motion detection will be. There are four time periods which you

can define different motion sensitivity values for. You can change what

time(s) each period starts and ends to best match the changing light-

ing conditions in your location. At night, you may get numerous false

triggers unless you raise the sensitivity setting, perhaps as high as 25 -

30. This is because when cameras use active infrared night vision, they

dramatically increase the gain controls to the image sensor. To find the

best sensitivity values for different times of day/night, it’s best to test the

system during different time periods. Get an able-bodied volunteer to

move about in front of the cameras you’d like to tune the sensitivity for.

The ideal sensitivity level is when your volunteer moving about always

triggers the motion detection, but there are no false triggers (or very

few) when your volunteer isn’t moving about.

Tap APPLY to save settings.

Alarm: Schedule

Schedule: Allows you to select which day and what time that you would

like Motion Detection to be enabled for. By default Motion Detection is

enabled 7 days a week for 24 hours. If you want to alter this, tap on the

day and time that you want to change.

Send Email: Tap this to enable if you would like to be alerted by email

whenever there is an alarm event.

Tap APPLY to save settings.

Andere Handbücher für SwannSecure

Inhaltsverzeichnis

Andere Swann Sicherheitssystem Handbücher

Swann

Swann SW245-SBD Bedienungsanleitung

Swann

Swann SWWHD-INTSOL Bedienungsanleitung

Swann

Swann SW276-ASL Bedienungsanleitung

Swann

Swann SW347-WA2 Bedienungsanleitung

Swann

Swann Advanced Quad Processor Bedienungsanleitung

Swann

Swann Retail Security Kit 4 CCTV Cameras SW244-SK4 Bedienungsanleitung

Swann

Swann REDALERT SW242-WDV Bedienungsanleitung

Swann

Swann SW347-WAK Bedienungsanleitung

Swann

Swann 4 CCTV Cameras Security Monitoring System Bedienungsanleitung

Swann

Swann ADW-340 Bedienungsanleitung

Swann

Swann RL-0507A Bedienungsanleitung

Swann

Swann DVR4-1000 Bedienungsanleitung

Swann

Swann SW351-WSA Bedienungsanleitung

Swann

Swann One Bedienungsanleitung

Swann

Swann ADW-350 Bedienungsanleitung

Swann

Swann DVR4-1100 Kurzanleitung

Swann

Swann Digital EagleEye ADW-400 Bedienungsanleitung

Swann

Swann SW351-CAC Bedienungsanleitung

Swann

Swann SWIFI-WDOORPK4 Bedienungsanleitung

Swann

Swann Advanced SWDVK-825508C Bedienungsanleitung

Swann

Swann USB 2.0 DVR Guardian Bedienungsanleitung

Swann

Swann DVR4-2500 Bedienungsanleitung

Swann

Swann MALARM1301012E Bedienungsanleitung

Swann

Swann DVR9-4200 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung