Swisher L213-224001 Bedienungsanleitung

OWNER’S

MANUAL

MANUAL DEL

PROPIETARIO

MANUEL DU

PROPRIÉTAIRE

SWISHER

1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093

PHONE 660-747-8183 FAX 660-747-8650

TELÉFONO 660-747-8183 FAX 660-747-8650

TÉLÉPHONE 660-747-8183 TÉLÉCOPIEUR 660-747-8650

Model Number

Número del modelo

Numéro de modèle

Assembly

Operation

Service and Adjustment

Repair Parts

Ensamblaje

Funcionamiento

Servicio y ajuste

Piezas para reparación

Assemblage

Utilisation

Réglage et entretien

Pièces de rechange

10698 REV 13-224

Trim-N-Mow

Visit us at www.swisherinc.com - Visítenos en www.swisherinc.com - Rendez-nous visite à : www.swisherinc.com

ST67522BS

ST67522BS-TSC

ST67522CC

DST67522BS

Starting Serial Number

Del número de serie

A partir du no de série

L213-224001

Read and follow all Safety

Precautions and Instructions before

operating this equipment.

IMPORTANT

IMPORTANTE

IMPORTANT

Lea y siga todas las advertencias e

instrucciones sobre seguridad antes de

poner en funcionamiento este equipo.

Avant de mettre en marche cet

équipement, lire le présent manuel et

suivre toutes les directives de sécurité

indiquées.Fabriqué aux

ÉTATS-UNIS

Made In The

USA

Hecho en

EE.UU.

Trim-Max

1) Engine Warranty All engines utilized on our products have a separate warranty extended

to them by the individual engine manufacturer. Any engine service

difficulty is the responsibility of the engine manufacturer and in no way

is Swisher or its agents responsible for the engine warranty. The Briggs

& Stratton Engine Service Hot Line is 1-800-233-3723.

2) Commercial Use This product is not intended for commercial use and carries no

commercial warranty.

3) Limitation This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the instructions

contained within this manual. This warranty does not apply to any

product of Swisher that has been subject to alteration, misuse, abuse,

improper assembly or installation, shipping damage, or to normal wear

of the product.

4) Exclusions Excluded from this warranty are normal wear, normal adjustments, and

normal maintenance.

In the event you have a claim under this warranty, you must return the product to an authorized service

dealer. All transportation charges, damage, or loss incurred during transportation of parts submitted for

replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions

concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number,

date of purchase, and the name of the authorized Swisher dealer from whom you purchased the mower will

be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED

HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of

consequential damages or limitations on how long an implied warranty may last, so the above limitations or

exclusions may not apply to you. This warranty gives you specific legal rights and you may have other

rights, which vary from state-to-state. This is a limited warranty as defined by the Magnuson-Moss Act of

1975.

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in

materials and workmanship for a period of two (2) years from the date of purchase by the original consumer

purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or

workmanship. This warranty is subject to the following limitations and exclusions:

•

Read, understand and follow all instructions in the manual and on the trimmer

before starting.

•Read this manual carefully. Become familiar with the controls and how to

operate the unit properly.

•Only allow responsible adults, who are familiar with the instructions, to

operate the unit.

•Clear the area of objects such as rocks, toys, etc. that could be thrown by the

unit.

•Be sure the area is clear of other people before trimming. Stop the unit if

anyone enters the area.

•Be aware of the direction of the trimmer discharge and do not direct it at

anyone. Do not direct trimmer discharge at breakable objects, such as

windows, etc.

•Do not operate trimmer without all guards and shields in place.

•Never leave the machine running unattended.

•Trim only in daylight or good artificial light.

•Do not operate the trimmer while under the influence of alcohol or drugs.

•Watch for traffic when operating near roadways.

•Use the trimmer as the manufacturer intended and as described in the

manual.

•Do not operate trimmer if it has been dropped or damaged in any manner.

Always have the damage repaired before operating.

•Always wear safety glasses or eye shields when using the trimmer.

•Dress properly. Do not operate the trimmer when barefoot or wearing open

sandals. Wear only solid shoes for good traction when trimming. Wear long

sleeved shirts or jackets, also long pants. Do not trim in shorts.

•Keep your eyes and mind on your trimmer and the area being trimmed.

•Do not let other interests distract you.

•Do not put hands and feet near or under rotating parts.

•Before cleaning, inspecting or repairing your trimmer, stop the engine and

disconnect the spark plug wire and keep it away from the spark plug to

prevent accidental starting.

•Do not operate the trimmer if it vibrates abnormally. Excessive vibration is a

sign of damage. Stop the engine and safely check for damage and repair as

required.

•Do not operate the trimmer in wet grass, where good footing may not be

possible. Walk, never run.

•Stop the trimmer when crossing gravel drives, etc.

Safety Instructions

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Slopesareamajor factor relatedtolossof control and slipaccidents,

whichcanresult insevereinjury. All slopesrequireextracaution. If you

feel uneasyonit donot trimit.

Slope Operation

•

DO: Trim across the face of a slope and not up and down.

•DO: Remove objects such as rocks, tree limbs, etc.

•DO: Watch for holes, ruts or bumps. Tall grass can hide obstacles.

•DO NOT: Mow near drop-offs, ditches or embankments. The operator could

lose footing or balance.

•DO NOT: Trim excessively steep slopes.

•DO NOT: Trim on wet grass. Reduced footing could cause slipping.

Children

•

Keep children out of the area and under the watchful care of another

responsible adult.

• Be alert and turn the machine off if children enter the area.

• Before and when backing, look behind and down for small children.

• Never allow children to operate this machine.

•

Use extra care when approaching blind corners, shrubs, trees or other objects

that may obstruct vision.

•Use extra care handling gasoline and other fuels. They are flammable and

vapors are explosive.

•Use only an approved container.

•Never remove gas cap or add fuel with the engine running.

•Allow engine to cool before refueling. Do not smoke while refueling.

•Never refuel the machine indoors.

•Never store the machine or fuel container where there is an open flame, such

as a water heater.

•Never run a machine inside a closed area.

•Keep nuts and bolts tight and equipment in good condition.

•Never tamper with safety devices.

•Keep machine free of grass, leaves or other debris build up. Clean oil or fuel

spillage. Allow machine to cool before storing.

•Stop and inspect the equipment if you strike an object. Repair if necessary

before restarting.

•Never make repairs or adjustments with the engine running.

Service

The operation of any mower can encounter foreign objects to be thrown into the eyes, resulting in

severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over

spectacles before starting any cutting machine and while operating such a machine.

The operation of any mower produces sound waves that are damaging to the human ear. Ear

protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of children. Children

are often attracted to the machine and the mowing activity. Never assume that children

will remain where you last saw them.

Do not operate the trimmer if it vibrates abnormally. Excessive vibration is a sign of damage.

Stop the engine and safely check for damage and repair as required.

Trim-Max Decal

OD64 Trim-N-Mow Decal

OD65

Caution Notice Decal

OD67

Trimmer Head

Instruction Decal

OD68

Handle Adjustment

Contents of Box:

• Trimmer

Parts bag containing:

• Manual

• Engine manual

• Safety goggles

• Bottle of engine oil

• Trimmer Line

• Cable Clip

Tools Required:

• ½” wrench

Installation of handles:

• Remove loose fasteners from lower handles.

• Pivot handles up and align lower hole in handles with hole on trimmer frame. Install

hardware removed in previous step. Snug, but do not tighten bolts.

• Pivot upper handles to fit the lower handles. Tighten knobs.

• Adjust handles for comfortable operation.

• Tighten all bolts.

Handles may be adjusted up and down and in and out for comfortable operation.

Installation of Wheels for Trim-Max

Refer to Page 12 for illustration.

•Slide axle through the mounting plates.

• Install conical springs with the large diameter side against the axle plate.

• Install spring retainer against the conical spring.

• Slip wheel on one side and install cotter pin.

• Bend cotter pin over to prevent it from falling out.

• Push the axle completely over to the other side.

• Install the second wheel and insert cotter pin and bend. Some compression of the

conical spring is necessary.

Assembly

To stop the trimmer:

• Release the control bail. Engine will stop immediately.

To start the trimmer:

• Remove any built up debris from engine.

• Pull control bail against the handle and hold.

• Push primer button on engine as directed.

• Pull back sharply on recoil starter handle.

• Begin trimming.

Important! For safest operation, make sure debris is directed away from you and others.

Preparing Unit For First Use

Operation

Trimming Tips

Important! To ensure proper operation, clean the engine and trimmer

regularly. Remove any build up of chaff from the top of the engine.

• Fill engine crankcase with oil. A bottle has been provided with this unit. DO

NOT OVERFILL.

• Fill the engine fuel tank with gasoline. GASOLINE SHOULD BE ADDED

OUTSIDE IN A WELL-VENTILATED AREA.

• Check to ensure string has been installed properly. A diagram is provided just

above the wheel for proper installation.

• Do not lift the trimmer head when trimming. Let the head rest lightly touching the ground.

• Keep an eye on the length of the trimmer line. As the line gets shorter they become less

effective at cutting and will take longer to trim properly. Replace the line as necessary (see

Installing Trimmer Line).

• Do not trim wet grass.

• Use caution when trimming slopes.

• Use the proper length on line. Using a line too long for the unit will cause stalling and

unacceptable operation.

Troubleshooting

•If engine will not start, remove and check air filter to make sure filter and

carburetor are clean.

Installing Trimmer Line

Trim-Max Operation

The Trim-

Max trimmer is designed to also be used as an edge trimmer and to offset left to

right for easier close trimming.

Edge Trimming/ Bevel Cutting

The trimmer disk may be tilted from horizontal to vertical so that it may be used as an

edge trimmer. The head may also be tilted slightly to trim closer. This may be handy for

trimming foundations without damaging the siding.

To Tilt:

•Stop unit.

•Make sure head is in the straight forward position (see Offset Trimming).

•Loosen the trimmer tilt clamp lever (clockwise)

•Tilt head to desired position.

•Tighten trimmer tilt clamp lever (counter-clockwise).

•Adjust lower trimmer shield to keep debris from coming back at operator.

Offset Trimming:

The trimmer head may be offset to the left or right to allow trimming under bushes, etc.

To Offset:

•Stop unit.

•Raise offset lever.

•Push or pull handles to achieve desired offset.

•Release offset lever. Make sure head has locked into position.

•Adjust lower trimmer shield to keep debris from coming back at operator.

Important! Note direction of debris when offsetting head.

Offsetting trimmer to the left is recommended.

Trim-Max Tilt Adjustment

Direction of Debris

Trim-Max Pivot Adjustment

Step 1 Step 2 Step 3

Important! Use the proper length of line. Using a line too long for the unit will cause

stalling and unacceptable operation.

Use 18” Trimmer Line Part Number P3618

•Loosely fold trimmer line in half.

•(1) Place loop of line against outside of loop on the trimmer head.

•(2) Bring ends around and through the loop and over the cutter line loop.

•(3) Pull ends to tighten loop.

Engine

•Refer to the engine service manual provided with this unit.

Belt

•Occasionally check the belt for wear. A worn belt should be replaced.

Belt Adjustment

•The TRIM-N-MOW has an automatic belt tightener and needs no further adjustment

•The TRIM-MAX has a

n automatic belt tightener that automatically adjusts when the head is tilted. If you

do not regularly tilt the head on your trimmer, it is recommended that you loosen the head twice a year

(see Edge Trimming).

Belt Replacement

•Remove front belt cover.

•Push trimmer head toward back of unit, compressing tensioner spring.

•Remove old belt.

•Install new belt by first routing belt under the engine and around the engine pulley.

•Push trimmer head toward back of unit, compressing tensioner spring.

•Install belt over front pulley.

•Release trimmer head. Ensure that belt is correctly installed in the groove of the engine and front pulleys.

Reinstall front belt cover.

Make sure your trimmer is in safe working condition by keeping the following guidelines in mind every

time you use your trimmer.

•Keep trimmer in good operating condition and keep all guards and shields in place. DO NOT operate

this trimmer if any of the shields and guards are missing.

•Check all fasteners for secure fit to keep equipment in safe working order. Make adjustments as

necessary.

•To reduce fire hazards, keep engine free of grass, leaves or excessive grease.

•DO NOT operate trimmer with a damaged or missing muffler. DO NOT tamper with exhaust system;

this may cause a fire hazard.

•DO NOT operate engine if air cleaner or the cover over the carburetor air intake is missing. Removal

of these parts could create a fire hazard.

•Before cleaning, making adjustments or repairing the trimmer, STOP engine, disconnect spark plug

wire and allow engine to cool.

•Handle gasoline with care. DO NOT smoke or use open flame near gasoline. Use only approved

gasoline containers. Never fuel or run trimmer in poorly ventilated areas, such as a garage or utility

building.

•Always replace fuel tank cap. Be sure to clean up any spilled gasoline.

•Do not change the engine governor settings or over-speed the engine; severe injury or damage may

result.

•Never store mower with gasoline in the tank

inside a building where fumes may reach an open flame or

spark. Always allow engine to cool before storing

Trimmer Maintenance

WARNING – ALWAYS STOP ENGINE AND DISCONNECT SPARK PLUG

WIRE BEFORE PERFORMING ANY ADJUSTMENTS OR SERVICE.

NEVER ADD GASOLINE TO A HOT ENGINE – ALLOW ENGINE TO

COOL BEFORE ADDING GASOLINE.

Trim-N-Mow

ST67522BS

ST67522BS-TSC

ST67522CC

Item # Description Part #

1 Briggs & Stratton Engine N/A

2 Nut - Serrated Flange 5/16-18 NB170

3 Bolt - Serrated Flange, 5/16-18 X 1 1/4 NB253

4 Pulley - Engine 2063

5 Washer - SP Bellville NB607

6 Bolt - HHC 3/8-24 X 1 NB238N

7 Cable - Operator Presence 2034B

8 Bolt - Serrated Flange, 5/16-18 X 2 1/4 NB622

9 Knob - Black Plastic 2030

10 Washer - SAE Flat 5/16 NB275

11 Handle - Bail 10397

12 Handle - Upper 10578*

13 Bolt - Carriage, 5/16-18 X 1 3/4 NB587

14 Handle - Lower 10399*

When ordering replacement parts

* USE PAINT CODE: TK=BLACK

Item # Description Part #

15 Guard - Belt 2019

16 Screw - .312-18 X .75 26X249

17 Belt - 57" 2113

18 Base - Lower Motor 2006*

19 Shield - Rubber 2027

20 Base - Upper Motor 2005*

21 Nut - Nyloc 1/2-13 NB281

22 Washer - .531 X 1 1/2 X .062 TR150W

23 Nut - Jam, 1/2-13 NB118

24 Washer - USS Flat, 1/2 NB555

25 Bolt - Serrated Flange, 5/16-18 X 3/4 NB596

26 Cover - Rear 2026*

27 Wheel 2002K

28 Bolt -1/2-13 X 4 NB132

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher T1260F Bedienungsanleitung

Swisher

Swisher ST67522CC Bedienungsanleitung

Swisher

Swisher POL10544C Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher ZT2766KP-CA Bedienungsanleitung

Swisher

Swisher Predator WB80024 Bedienungsanleitung

Swisher

Swisher ST50022STDQ Bedienungsanleitung

Swisher

Swisher FT1150 Bedienungsanleitung

Swisher

Swisher T1260, T1360, T1460 Bedienungsanleitung

Swisher

Swisher QuadBoss QBRT10544 Bedienungsanleitung

Swisher

Swisher Z Series Bedienungsanleitung

Swisher

Swisher TRAILMOWER POL14560X Bedienungsanleitung

Swisher

Swisher ZT1436B, ZT18542, ZT2250 Bedienungsanleitung

Swisher

Swisher T14560A Bedienungsanleitung

Swisher

Swisher ZTR2460BS-CA Bedienungsanleitung

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Swisher

Swisher FC14560BS Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher Trim-N-Mow Plus STS67522BS Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Swisher

Swisher PST67522A Bedienungsanleitung

Swisher

Swisher T1260, T1360, T1460 Bedienungsanleitung

Swisher

Swisher SCOLA Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung