Swisher ZT1436B, ZT18542, ZT2250 Bedienungsanleitung

ZERO TURN HYDROSTATIC DRIVE

ZERO TURN HYDROSTATIC DRIVEZERO TURN HYDROSTATIC DRIVE

ZERO TURN HYDROSTATIC DRIVE

OWNER’S

MANUAL

1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093

P ONE 660-747-8183 FAX 660-747-8650

MODEL NO.

ZT1436B

ZT18542

ZT2250

Manufacturing quality lawn care equipment since 1945

Assembly

Operation

Service and Adjustment

Repair Parts

Made In The

USA

Rev. 06-039

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

ONZTR04

“Z” SERIES

“Z” SERIES“Z” SERIES

“Z” SERIES

1) Engine Warranty All engines utilized on our products have a separate warranty extended

to them by the individual engine manufacturer. Any engine service

difficulty is the responsibility of the engine manufacturer and in no way

is Swisher ower Co., Inc. or its agents responsible for the engine

warranty. The Briggs & Stratton Engine Service Hot-Line is 1-800-233-

3723. The Tecumseh Engine Service Hot-Line is 1-800-558-5402.

2) Commercial Use This product is not intended for commercial use and carries no

commercial warranty.

3) Limitation This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the instructions

contained within this manual. This warranty does not apply to any

product of Swisher ower Co., Inc., that has been subject to alteration,

misuse, abuse, improper assembly or installation, shipping damage, or to

normal wear of the product.

4) Exclusions Excluded from this warranty are normal wear, normal adjustments, and

normal maintenance.

In the event you have a claim under this warranty, you must return the product to an authorized

service dealer. All transportation charges, damage, or loss incurred during transportation of parts

submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you

have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The

model number, serial number, date of purchase, and the name of the authorized Swisher dealer from

whom you purchased the mower will be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DA AGES AND ANY I PLIED WARRANTIES ARE LI ITED TO THE SA E TI E

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow

the limitation of consequential damages or limitations on how long an implied warranty may last, so

the above limitations or exclusions may not apply to you. This warranty gives you specific legal

rights and you may have other rights, which vary from state-to-state. This is a limited warranty as

defined by the agnuson- oss Act of 1975.

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects

in materials and workmanship for a period of two (2) years from the date of purchase by the original

consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to

materials or workmanship. This warranty is subject to the following limitations and exclusions:

TABLE OF CONTENTS

WARRANTY………………....….2

INTRODUCTION………………..3

SAFETY…………………………3-6

ASSE BLY/OPERATION……..7-8

AINTENANCE………………9-10

SERVICE / ADJUST ENT……….…11-14

WIRING DIAGRA ………………….15

PARTS BREAKDOWN……………...16-28

TROUBLESHOOTING………………..29

SLOPE GUIDE…………………………30

Thank you for choosing Swisher’s Zero Turn Rider ower. Before

operating your mower, please read, understand and follow all of the safety

precautions and other instructions explained in this manual . As with all power

equipment, lawnmowers can be potentially dangerous if improperly used.

SAFETY PRECAUTIONS & DECALS

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands and feet, and

throw objects. Failure to observe the following safety instructions could result in

serious injury or death.

•Read the manual. Learn to operate this machine safely.

•Always disconnect the spark plug wire and place the wire where it cannot contact the

spark plug, to prevent accidental starting the engine when setting up, transporting,

adjusting or making repairs.

•Keep all shields and guards in place.

•Understand the speed, steering and stability of this machine. Know the positions and

operations of all controls before you operate this machine. Check all of the controls in

a safe area before starting to work with this machine.

•Allow only responsible adults who are familiar with these instructions to operate this

machine. Never allow children to operate this machine.

•Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and

thrown by the blade.

•Be sure the area is clear of other people before mowing. Be aware of the mower

discharge direction and do not point at anyone. Stop the machine if anyone enters the

mowing area. Children are often attracted to the machine and the mowing activity.

Never assume that children will remain where you last saw them.Keep children

under the watchful care of another responsible adult.

•No riders!

•Do not put hands or feet near or under rotating parts. Keep clear of the discharge

opening at all times.

•Do not mow in reverse. Always look down and behind before and during backing.

• Turn off the blades when not mowing. Before leaving the machine, turn off the blades

and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner or if the

mower vibrates excessively. Excessive vibration is an indication of damage.

Repair mower as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open sandals.

Wear only solid shoes with good traction when mowing.

• Never allow operation by untrained persons.

• Do not operate the machine while under the influence of alcohol or drugs.

• Operate self-propelled machines up and down slopes. There is significant risk of

overturns when operating across slopes. Avoid sudden turns. Operate walk-behind

machines across slopes. There is a significant risk of slipping under a walk-behind

machine when operating up and down slopes.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before

restarting. Never make adjustments or repairs with the engine running. ower blades

are sharp and can cut. Wrap the blades or wear gloves, and use extra caution when

servicing them. Do not operate at too fast a rate.

• Do not mow close to ditches, embankments or drop-offs. An edge could collapse. A

mower wheel over the edge could suddenly turn the unit over.

• Do not mow on wet grass if possible. Wet grass causes reduced traction and could cause

sliding. Do not park on a slope unless absolutely necessary.

• Always chock or block wheels and set parking brake if parked on slope.

The operation of any cutter can encounter foreign objects to be thrown into the

eyes, resulting in severe eye damage. Always wear certified safety glasses or

wide-vision safety goggles for over spectacles before starting any cutting

machine and while operating such a machine.

The operation of any cutter produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw

them.

SLOPE OPERATION! ( See page 27 )

Do not operate on slopes greater than 15 degrees.

Use extra caution when mowing on slopes. Operate self-propelled units

up and down slopes. There is a significant risk of overturns when

operating across slopes. If you feel uneasy on a slope then do not mow it.

• Turn off the blades when not mowing. Before leaving the machine, turn off the blades

and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner or if the

mower vibrates excessively. Excessive vibration is an indication of damage.

Repair mower as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open sandals.

Wear only solid shoes with good traction when mowing.

• Never allow operation by untrained persons.

• Do not operate the machine while under the influence of alcohol or drugs.

• Operate self-propelled machines up and down slopes. There is significant risk of

overturns when operating across slopes. Avoid sudden turns. Operate walk-behind

machines across slopes. There is a significant risk of slipping under a walk-behind

machine when operating up and down slopes.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before

restarting. Never make adjustments or repairs with the engine running. ower blades

are sharp and can cut. Wrap the blades or wear gloves, and use extra caution when

servicing them. Do not operate at too fast a rate.

• Do not mow close to ditches, embankments or drop-offs. An edge could collapse. A

mower wheel over the edge could suddenly turn the unit over.

• Do not mow on wet grass if possible. Wet grass causes reduced traction and could cause

sliding. Do not park on a slope unless absolutely necessary.

• Always chock or block wheels and set parking brake if parked on slope.

WARNING: Hydraulic fluid can cause severe burns and penetrate skin causing

severe injury or death.

•Do not step on mower deck when operating, dismounting or mounting the mower.

•Never push or pull unit with another vehicle. Transmission damage will occur.

•When transporting be sure to secure mower frame to transport vehicle. NEVER tie

down to moving parts or linkages which may become damaged or come loose.

•NEVER transport mower while engine is running.

•NEVER add fuel or remove gas cap while engine is running or hot.

•NEVER store unit near an open flame such as a water heater or furnace.

•NEVER modify or allow anyone to modify or alter any components or safety

devices.

•ALWAYS keep mower clean and free of debris and grass clippings.

•NEVER reverse battery cables. Electric shock will occur.

•ALWAYS keep battery away from open flame and sparks. Explosive gases from

battery can cause serious injury or death.

•ALWAYS wear safety glasses and protective gear when servicing the battery.

Battery fluid contains sulfuric acid. Contact with battery acid on skin or clothing can

cause severe chemical burns.

•NEVER tip battery beyond a 45 degree angle in any direction.

Danger/Warning Decal – OD99155

Ignition/PTO/Throttle Decal – OD99154

Triangle Danger Decal – OD55

Ignition/PTO/Throttle Decal 50” ower Only – OD99157

Swisher Flag U.S.A.– OD39 Notice Do Not Alter Wiring Decal– OD74

Operator ust Be Seated Decal– OD73

Parking Brake Decal – OD99152

Flying Debris Decal – OD43

No Step Decal – OD11

Z 18.5/42" Decal - OD122

Swisher Z 18.5/42" Decal-Right– OD120

Swisher Z 18.5/42" Decal-Left- OD124

DECALS NOT S OWN

Height of Cut Decal - OD99153

Height Indicator Decal - OD99151

Z 22.0/50" Decal- OD123

Swisher Z 22.0/50" Decal- Right- OD121

Swisher Z 22.0/50" Decal- Left- OD125

50" Deck White Decal- OD99160

Small Logo White Decal- OD99156

Swisher Patent Decal– OD88

42" Deck White Decal- OD99126

36" Deck White Decal- OD99159

Z 14.5/36" Decal- OD112

Swisher Z 14.5/36" Decal- OD108

OPERATING YOUR NEW ZERO TURN RIDER MOWER

CONTROLS

•OPERATOR PRESENCE SYSTEM: This mower is equipped with an operator’s presence

system. Any attempt to leave the seated position with the engine running, without first

disengaging the PTO switch will cause the engine to shut off. Never get off the mower

without placing the steering levers in the neutral position.

WARNING: Do not operate the machine unless the Operator’s Presence System is

functioning as described.

•PARKING BRAKE: Always set the parking brake before starting. The parking brake is

located on the drivers left hand side. Engage the parking brake by pushing the lever rearward

and down until lever locks into position. Be sure to release parking brake before operating the

machine.

•IGNITION: The ignition switch is located on the drivers right hand side toward the rear of

the seat. The ignition switch has three positions: OFF, ON, START.

•T ROTTLE: The throttle\choke control is located on the drivers right hand side towards the

front of the seat. For maximum performance and battery charging, operate mower at full

throttle. When starting a cold engine, place lever forward in the full choke position. After start

up, move throttle rearward to full throttle position. ove lever all the way to the rear for

lowest setting before shutting off engine. The 50” odel has a push/pull choke mounted on

the right side fender for easier cold weather starts. Pull out to choke (start) engine.

•PTO SWITC : The PTO, or Power Take Off switch is used to engage the blades of the

mower. When the PTO switch is pulled out the blades will be engaged. When the PTO switch

is pushed in the blades will be disengaged. The PTO switch must be pushed in to complete the

Operator’s Presence System to start engine.

•NEUTRAL LOCK: The steering levers must be in the outward and locked position for the

mower to start. ( See page 11)

• Dispose of top and side panels of the crate.

• Remove loose parts and packing material.

• Cut any banding or strapping that may be holding the mower to the crate.

• Disengage spark plug wire and place where it cannot make a connection.

• Assemble the seat and clip wiring harness into the bottom of seat.

NOTICE: ower will not start unless the seat is connected to the wiring harness.

• Raise mower deck to its highest position by turning the handle clockwise.

• Set parking brake to Disengage.

• Open transmission valves from behind by pushing-IN on each of the levers until they stop;

rotate them to the locked (left) position. (See Page 14)

• Carefully push the mower off the crate to a safe and level area.

• Check engine oil. All engines are filled with oil and tested at the factory. Verify oil level and

add if necessary before starting engine. (See Engine Owner’s anual)

• Check the battery. If battery is put into service after the “month & year” of the date on the

battery, then it may need to be charged with a 12 volt battery charger for a minimum of 1 hour,

but no more than 2 hours at a rate of 6 to 10 amps.

• Attach battery cable(s) to battery.

• Install steering levers. Align steering lever with holes in steering linkage on mower. Keep

levers aligned with each other.

• Reconnect spark plug wire.

UNCRATING/ASSEMBLY

STARTING MOWER

•TO START: Position steering handles outward to neutral locked position. Engage parking

brake. Extend throttle to full choke position. Start ignition and slide throttle lever back to full

throttle position. Allow engine to warm up for 1 minute. Release parking brake. odel

ZT2250 has a remote choke assembly located on the right fender, behind the rider.

•FORWARD MOVEMENT: Position steering handles inward to the drive position. To move

the mower forward gently push both steering levers forward equal distance from the neutral

position. The further you move the levers forward the faster you will travel. CAUTION

steering levers have quick response timing.

•BACKWARD MOVEMENT: To move the mower backwards, gently pull back on the

steering levers the same distance from neutral. The further you pull back the faster you will

travel. NOTE it is normal for the reverse speed to be less than the forward for easier turning.

•TURNS: For left turn, move the right lever farther forward then the left. For right turn, move

the left lever farther forward than the right. To obtain a tight turning radius, GENTLY reverse

one lever and push the other lever forward. CAUTION: Aggressive turns can damage lawns.

Do not make turns with the inside wheel stopped. It it better to keep both wheels turning

slightly.

•DECK EIG T ADJUSTMENT: To raise the mower deck up and down, simply rotate the

lever located in front of the seat above the floor plate. Clockwise raises the deck.

Counterclockwise lowers the deck. The deck is adjustable from 1 ½” to 3 ½”.

• For best performance, tall grass should be mowed once in the highest position and once again

at desired cut height. Never cut more than1/3 the height in one cutting.

•ENGAGING BLADES: Operator must be seated for operation of blades. With engine to full

throttle position, pull UP on PTO switch located between the throttle and the key switch. To

disengage blades, push DOWN on PTO switch.

•STOPPING ENGINE: Place both levers in the outward neutral locked position. Push PTO

switch in to disengage. Place throttle lever to lowest setting and let idle for 30 seconds. Turn

off ignition key and engage parking brake.

MOWING

WARNING: Do not operate mower at too fast of a rate. Sudden movements forward and

backward at fast speeds can cause accidents resulting in personal injury.

• Start out moving steering levers SLOWLY forward and backward until you learn to operate

the unit. NOTE: This mower has been designed to be very maneuverable. Practice in open,

flat areas is extremely necessary to become comfortable and efficient with the controls.

•BEGIN TO MOW: Before starting the engine, set the desired deck height.

• Start the mower engine.

• Position the throttle lever about halfway and engage PTO switch. Reposition throttle lever

to full throttle position.

• ove steering levers forward to begin mowing.

CAUTION: Always make sure the deck is not plugged with grass or other debris. Failure

to do this will cause damage to the PTO belt.

•STOPPING: Hydrostatic mowers use hydrostatic braking through the transmissions. To

slow or stop the unit move the steering levers to the neutral position

•STOPPING T E ENGINE: ove the throttle lever to slow position, allow engine to idle

for 30 seconds and turn ignition to off position. CAUTION: Failure to position the ignition

key to any position except off will cause discharge of the battery.

MAINTENANCE SC EDULE

INSPECT BEFORE EAC USE

•Loose fasteners: Be sure all fasteners are at proper torque. Especially guards and

blades.

•Parking brake: If brake does not keep unit from rolling, brake must be adjusted or

repaired.

•Tires: Always check and maintain proper tire pressure (See tire sidewall for

recommendation). Check for damage due to sharp rocks, objects or stumps.

•Operator Presence System: The engine should not start unless the PTO switch is

disengaged and the control levers are locked in the neutral position. Any attempt to

leave the seated position with the PTO switch engaged will kill the engine.

•Oil level: To prevent damage to engine, always check and maintain proper oil level.

Never operate engine with the oil level below the add mark on the dipstick. Be sure

to tighten the dipstick securely after inspection. Refer to engine manual for additional

information.

INSPECT EVERY 8 OURS

•Proper cleaning: Remove any build up of grass, dirt or debris with a brush or cloth

from engine, battery, deck and and transaxles. Do not use harsh chemicals or

abrasives. Keep all painted surfaces and wheels free of oil and gasoline. Protect all

painted surfaces with an automotive wax. Do not spray unit with water or store

outdoors unprotected. Water can invade sealed bearings and reduce component life.

•Air filter: The engine will not run properly with a dirty or damaged air filter. Check

filter before starting the engine. Check for buildup of dirt or debris. Replace if bent,

clogged, or damaged.

•Oil level: To prevent damage to engine, always check and maintain proper oil level.

Never operate engine with the oil level below the add mark on the dipstick. Be sure to

tighten the dipstick securely after inspection.

Do not spray water onto hydrostatic transmissions. This will

cause injection of water into the unit causing failure.

INSPECT EVERY 25 OURS

•Lubrication: Grease all pivot points with a high temp grease.

•Battery, check and clean: Keep battery terminals clean and tight. Periodic charging

will extend its life. Clean terminals with a wire brush and coat with a petroleum jelly.

•Change engine oil and filter: Use only quality detergent oil. See engine manual for

instructions. Select viscosity grade according to your expected environmental

temperature.

•Blades: Best results will come from sharp blades. Replace if bent, damaged or worn.

•Engine air screen: Screen must be clean and free of debris for proper engine cooling.

Clean with a brush or cloth. Do not spray with pressurized water.

•Muffler: Inspect for damage or corrosion. Keep free of grass or debris to prevent fire.

INSPECT EVERY 100 OURS

•Clean engine cooling fins: Clogged cooling fins can damage engine due to

overheating. Keep fins and external surfaces of the engine clean.

•Replace air filter: The engine will not run properly with a dirty or damaged air filter.

Check filter before starting the engine.Check for buildup of dirt or debris. Replace if

bent, clogged, or damaged. See engine manual for detailed instructions.

•Replace spark plugs: See engine manual for detailed instructions.

INSPECT EAC SEASON

•Belts:Check belts for wear and deterioration. See service and adjustments.

•Spark plug: See engine manual for detailed instructions.

•Replace in-line fuel filter: Replace every season.

INSPECT BEFORE STORAGE

•Change engine oil and filter: See engine manual for detailed instructions.

•Lubrication: Grease all pivot points with a high temp grease.

•Check battery: Keep battery terminals clean and tight. Periodic charging will extend

its life. Clean terminals with a wire brush and coat with a petroleum jelly.

•Loose fasteners: Be sure all fasteners are at proper torque, especially guards and

blades.

Andere Handbücher für ZT1436B, ZT18542, ZT2250

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher Z-MAX ZT2560 Bedienungsanleitung

Swisher

Swisher QuadBoss COMMERCIAL PRO QBFC14560CP Bedienungsanleitung

Swisher

Swisher PREDATOR TALON WBRC11524C Bedienungsanleitung

Swisher

Swisher PST5022 Bedienungsanleitung

Swisher

Swisher Z-MAX ZT2350A Bedienungsanleitung

Swisher

Swisher ZT1436 Bedienungsanleitung

Swisher

Swisher TRAILMOWER POL14560X Bedienungsanleitung

Swisher

Swisher FC14566CPKA Bedienungsanleitung

Swisher

Swisher ZT17542 Bedienungsanleitung

Swisher

Swisher T844CH Bedienungsanleitung

Swisher

Swisher QUADBOSS QBFC14560 Bedienungsanleitung

Swisher

Swisher WB80042F Bedienungsanleitung

Swisher

Swisher L213-224001 Bedienungsanleitung

Swisher

Swisher QUADBOSS QBFC1966 Bedienungsanleitung

Swisher

Swisher RESPONSE ZTR2354KA Bedienungsanleitung

Swisher

Swisher L116-245001 Bedienungsanleitung

Swisher

Swisher FC11544BS Bedienungsanleitung

Swisher

Swisher ST60022 Bedienungsanleitung

Swisher

Swisher T14560A Bedienungsanleitung

Swisher

Swisher QUADBOSS QBFC14560-CA Bedienungsanleitung

Swisher

Swisher ZT2452 Bedienungsanleitung

Swisher

Swisher ZT2454K Bedienungsanleitung

Swisher

Swisher Ride King Bedienungsanleitung

Swisher

Swisher POL1250F Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung