Swisher WRC10224HC Bedienungsanleitung

OWNER’S MANUAL

SWISHER ACQUISITION INC.

1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093

PHONE 660) 747-8183 FAX 660) 747-8650

Operation

Service and Adjustment

Repair Parts

FOR MODELS – WRC10224HC, WRC10224H, WRC11524BSC, WRC11524BS

swisherinc.com

21919 REV 18-335

STARTING SERIAL #:

L118-335001

24” WALK BEHIND

Rough Cut Trail Cutter

RECOIL AND ELECTRIC START MODELS

ade I The

USA

of US and Global Parts

PREDATOR TALON

COMMERCIAL PRO

WRC10224HC

PREDATOR

COMMERCIAL PRO

WRC10224H

PREDATOR TALON

WRC11524BSC

PREDATOR

WRC11524BS

WRC11524CL

Read and follow all Safety Precautions and Instructions before

operating this equipment.

IMPORTANT



In th v nt you hav a claim und r this warranty, you must r turn th product to an authoriz d

s rvic d al r. All transportation charg s, damag , or loss incurr d during transportation of parts

submitt d for r plac m nt or r pair und r this warranty shall b born by th purchas r. Should you

hav any qu stions conc rning this warranty, pl as contact us toll-fr at 1-800-222-8183. Th

mod l numb r, s rial numb r, dat of purchas , and th nam of th authoriz d Swish r d al r from

whom you purchas d th mow r will b n d d b for any warranty claim can b proc ss d.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Som stat s do not

allow th limitation of cons qu ntial damag s or limitations on how long an impli d warranty may

last, so th abov limitations or xclusions may not apply to you. This warranty giv s you sp cific

l gal rights and you may hav oth r rights, which vary from stat -to-stat . This is a limit d warranty

as d fin d by th Magnuson-Moss Act of 1975.

LIMITED WARRANTY

Th manufactur r’s warranty to th original consum r purchas r is: This product is fr from d f cts

in mat rials and workmanship for a p riod of (1) y ar from th dat of purchas by th original

consum r purchas r. W will r pair or r plac , at our discr tion, parts found to b d f ctiv du to

mat rials or workmanship. This warranty is subj ct to th following limitations and xclusions:

TABLE OF CONTENTS

WARRANTY………………....….2

INTRODUCTION………………..3

SAFETY..……………………….3-4

PRE-OPERATING..….……..……4

OPERATION.……………………….6-8

DECALS…..………….……………….9

PARTS BREAKDOWN…………….10-16

ELECTRICAL & BELT ROUTING...17, 18

1) Engin Warranty

• All ngin s utiliz d on our products hav a s parat r sid ntial or comm rcial

warranty xt nd d to th m by th individual ngin manufactur r. Any ngin

s rvic is th r sponsibility of th ngin manufactur r and in no way is Swish r or

its ag nts r sponsibl for th ngin warranty. Pl as visit ngin s.honda.com and

click on find a d al r or find a distributor. Th Briggs & Stratton Engin S rvic Hot

Lin is 1-800-233-3723.

2) Limitation

• This warranty appli s only to products which hav b n prop rly ass mbl d,

adjust d, and op rat d in accordanc with th instructions contain d within this

manual. This warranty do s not apply to any product of Swish r that has b n subj ct

to alt ration, misus , abus , improp r ass mbly or installation, shipping damag , or

to normal w ar of product.

3) Comm rcial Us

• Only Comm rcial Pro brand d Walk B hind Rough Cut Trail Cutt rs ar warrant d

for comm rcial us for a p riod of (1) y ar from th dat of purchas . Non

Comm rcial Pro Products ar not int nd d for comm rcial us and carry no

comm rcial us warranty.

4) Exclusions

• Exclud d from this warranty ar normal w ar, normal adjustm nts, and normal

maint nanc .

縀ə

SAFETY PRECAUTIONS

Read this manual completely. This machine can amputate hands and feet, and

throw objects. Failure to observe the following safety instructions could result in

serious injury or death.

Thank you for choosing Swish r’s 24” Walk B hind Rough Cut. B for

op rating your Walk B hind, pl as r ad, und rstand and follow all of th saf ty

pr cautions and oth r instructions xplain d in this manual. As with all pow r

quipm nt, lawn mow rs can b pot ntially dang rous if not prop rly us d.

• R ad th manual. L arn to op rat this machin saf ly.

• Always disconn ct th spark plug wir and plac th wir wh r it cannot contact th spark plug

to pr v nt accid ntal starting th ngin wh n s tting up, transporting, adjusting or making r pairs.

• K p all shi lds and guards in plac .

• Und rstand th sp d, st ring and stability of this machin . Know th positions and op rations of all

controls b for you op rat this machin . Ch ck all of th controls in a saf ar a b for starting to

work with this machin .

• Allow only r sponsibl adults who ar familiar with th s instructions to op rat this machin .

Never allow children to operate this machine.

• Cl ar th ar a of obj cts such as rocks, toys, wir , tc. that can b pick d up and thrown by th blad .

• B sur th ar a is cl ar of oth r p opl b for mowing. B awar of th mow r discharg dir ction

and do not point at anyon . Stop the machine if anyon nt rs th mowing ar a. Childr n ar oft n

attract d to th machin and th mowing activity. Never assume that children will remain where

you last saw them. K p childr n und r th watchful car of anoth r r sponsibl adult.

•No riders!

• Do not put hands or f t n ar or und r rotating parts.

• Do not mow in r v rs . Always look down and behind before and during backing.

• Turn off th blad wh n not mowing. B for l aving th machin , turn off th blad and stop th

ngin .

• Watch for traffic wh n op rating n ar or crossing roadways.

• Do not op rat th mow r if it has b n dropp d or damag d in any mann r or if th mow r vibrat s

xc ssiv ly. Exc ssiv vibration is an indication of damag . R pair mow r as n c ssary.

• Dr ss prop rly. Do not op rat th mow r wh n bar foot or w aring op n sandals. W ar only solid

sho s with good traction wh n mowing.

• N v r allow op ration by untrain d p rsons.

• Do not op rat th machin whil und r th influ nc of alcohol or drugs.

• Do not op rat on slop s gr at r than 15 d gr s.

• Stop and insp ct th quipm nt if you strik an obj ct. R pair, if n c ssary, b for r starting. N v r

mak adjustm nts or r pairs with th ngin running.

• Mow r blad s ar sharp and can cut. Wrap th blad s or w ar glov s, and us xtra caution wh n

s rvicing th m.

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

㳀ӝ

Become familiar with the controls and their locations before operating.

Use the figures below to find the general locations for controls and

features discussed later in this manual

Briggs & Stratton Mod ls Honda Mod ls

• Dis ngag spark plug wir and plac wh r it cannot mak a conn ction.

• Ch ck th ngin oil. All ngin s ar fill d with oil at th factory. V rify oil l v l and

add if n c ssary b for starting ngin (S Engin Own r’s Manual).

• V rify fu l l v l and add if n c ssary b for starting ngin .

• R conn ct spark plug wir .

• R f r to pag s 6-8 in this manual for prop r op rating proc dur s.

PRE-OPERATING INSTRUCTIONS

IMPORTANT: These engine may not be equipped

with a spark arrester muffler. It is a violation of

California Publi Resour e Code Se tion 4442 to

use or operate the engine on any forest- overed,

brush- overed, or grass- overed land. Other states

or federal areas may have similar laws.

彆

A batt ry is not shipp d from th factory with th th s units. Batt ri s ar classifi d by th ir physical siz ,

and individual siz cat gori s ar giv n a "group numb r" by th Batt ry Council Int rnational. This Walk

B hind Trail Cutt r was d sign d to us a U1 batt ry group siz or small r.

Us a 12-volt batt ry with a minimum of 230 cold cranking amps (CCA)

B car ful not to conn ct th batt ry in r v rs polarity, as this will short circuit th batt ry charging syst m.

Always conn ct th positiv (+) batt ry cabl to th batt ry t rminal b for conn cting th n gativ (-)

batt ry cabl , so your tools cannot caus a short circuit if th y touch a ground d part whil tight ning th

positiv (+) batt ry cabl nd.

Th batt ry positiv (+) cabl is conn ct d to th start r sol noid t rminal as shown. And th batt ry

n gativ (-) cabl is conn ct d to th ngin mounting bolt at th factory.

1. Conn ct th RED batt ry positiv (+) cabl to th batt ry positiv (+) t rminal as shown.

2. Conn ct th BLACK batt ry n gativ (-) cabl to th batt ry n gativ (-) t rminal as shown.

A battery can explode if you do not follow the correct

procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away

from the battery.

BATTERY CONNECTIONS FOR ELECTRIC STARTER

applicable models)



Th op ration of any mow r can produc for ign obj cts to b thrown into th

y s, r sulting in s v r y damag . Always w ar c rtifi d saf ty glass s or

wid -vision saf ty goggl s ov r sp ctacl s b for starting any cutting machin and

whil op rating such a machin .

Th op ration of any mow r produc s sound wav s that ar damaging to th

human ar. Ear prot ction is r comm nd d.

CAUTION!

Tragic accid nts can occur if th op rator is not al rt to th pr s nc of

childr n. Childr n ar oft n attract d to th machin and th mowing

activity. Never assume that children will remain where you last saw them.

OPERATING YOUR NEW WALK BEHIND

INTENDED USE

This is not a lawn mow r. Th Pr dator and Pr dator Talon is d sign d for cutting

ov rgrown brush, w ds, and oth r typ s of organic growth. This unit is capabl of

cl aring small saplings of 1.5” in diam t r or l ss to a h ight of approximat ly 4”.

TRAVEL SPEED

Sp d can b chang d by choosing a high r or low r g ar using th g arshift l v r

locat d on th handl bars. Do not adjust th sp d with th blad ngag d. To shift th

cutt r into r v rs , r l as th “GROUND CONTROL” l v r, dis ngag th blad , and

rotat th shift l v r to th l ft. Pr ss down slightly on th l v r to pass th st p and

continu to rotat th l v r to th l ft “R” position.

PROPULSION

Th Pr dator and Pr dator Talon ar s lf-prop ll d and controll d by a “GROUND

CONTROL” l v r. To ngag th driv , shift th transaxl to a g ar and activat th l ft

handl bar l v r by squ zing it against th handl . R l asing th l v r will dis ngag

th s lf-prop l.

Und r most conditions cutting should b don in a low g ar (1st or 2nd). Upp r g ars

should b us d for conditions wh r w ds and brush ar thinn d out or not as tall. In

confin d ar as th machin can b push d forwards or backwards by r l asing th

“GROUND CONTROL” l v r, shifting th transaxl to n utral, and pushing th

machin .

ENGAGING THE BLADE

An “OPERATOR PRESENCE” l v r and a “BLADE ENGAGE” control work tog th r

to ngag th blad . Both d vic s must b activat d b for th blad will work.

R l asing th “OPERATOR PRESENCE” l v r will dis ngag both th blad and th

“BLADE ENGAGE” control.

쯀ӝ

STARTING THE ENGINE

S ngin manufactur r’s r comm ndations for th typ and amount of oil and fu l us d.

Engin must b l v l to accurat ly ch ck and fill oil. Do not ov rfill.

• Mak sur unit is l v l, blad is dis ngag d, and transaxl in “NEUTRAL”

• Ch ck spark plug wir , oil l v l, and fu l l v l.

• Ch ck all l ctrical conn ctions for build-up of d bris.

• If quipp d with a fu l shutoff valv , turn th valv to th ON position.

• Mov throttl control to “FAST”, or “CHOKE” if chok is n d d.

• Honda Engin s

• For r coil starting, turn ignition k y to th “ON”

position and pull rop with a

singl fluid motion. For l ctric starting, turn th k y to th “START” position.

• Briggs and Stratton Engin s

• Flip th ngin control switch to th “ON” position.

• Pull th start r cord slowly until r sistanc is f lt and th n pull rapidly to avoid

kickback, r p at until th ngin has start d.

• If “CHOKE” was us d, r turn th l v r to th “RUN” position.

• S t ngin throttl control to “FAST”. Th throttl must b s t in th fast position for

maximum p rformanc .

STOPPING

• Bring th Walk B hind to a compl t stop by r l asing th “GROUND CONTROL” l v r

(l ft handl bar l v r).

• Dis ngag mow r blad by r l asing th “OPERATOR PRESENCE” l v r (right handl

bar l v r).

• R duc ngin idl sp d, and allow ngin to run mom ntarily for cooling.

• Turn th ignition k y (for 12v mod ls) or ngin control switch to th “OFF” position.

BREAKING IN YOUR WALK BEHIND

• Start th ngin prop rly.

• Slowly ngag blad control l v r whil holding th right op rator pr s nc handl bar

l v r down.

• Und r sup rvision, allow blad to rotat and ngin to idl for 5 minut s.

• Dis ngag blad .

• Shift through ach g ar. Whil in ach g ar ngag th “GROUND CONTROL” l v r and

trav l 20 yards to nsur transaxl works prop rly.

BEGIN CUTTING

• Mak sur ar a is cl ar of all bystand rs.

• Mak sur that all guards, b lt guid s, and th spark plug wir ar prop rly attach d.

• Start ngin , s t ngin throttl control at maximum ngin idl sp d for b st r sults.

• Allow ngin to run a f w mom nts and slowly ngag blad .

• Mov transaxl into low g ar and activat “GROUND CONTROL” l v r.

• Turning is don by rotating th handl s l ft or right. This machin has significant w ight

and may tak mor ffort to turn than on may xp ct. Turning could tak practic .

鞐Ӡ

BACKING UP

• R l as th Op rator Pr s nc l v r on th right handl bar to dis ngag th blad .

• Ch ck b hind you to mak sur your path is cl ar.

• Mov th shift l v r to th r v rs position “R” and d pr ss th “GROUND

CONTROL” l v r on th l ft handl bar.

TRANSPORTING

• R mov th k y from ignition switch if quipp d.

• Shut off th fu l at th ngin .

• S cur in plac with appropriat straps whil th unit is b ing transport d.

• Unit should b l ft in low g ar to avoid any slight rolling.

SUGGESTED PRACTICES

• Always op rat with th ngin at full throttl wh n cutting to assur th b st cutting

p rformanc .

• If th ar a is w t, allow it to dry. W t w d clumps will coll ct on th bottom of th

d ck.

• Go slow wh n cutting d ns ar as. Som d ns ar as may n d to b gon ov r

twic . B tt r r sults ar achi v d if th s cond cut is 90 d gr s to th first cut.

BEFORE EACH SEASON

A n w spark plug and a cl an air filt r will assur prop r air-fu l mixtur and h lp your ngin

run b tt r and last long r.

• R plac th spark plug.

• Cl an or r plac th air filt r.

• Ch ck blad s and b lts for w ar.

BEFORE EACH USE

• Ch ck your ngin oil l v l. Do this twic to nsur an accurat r ading.

• Ch ck th condition of air filt r and cl an or r plac if n c ssary.

• Ch ck for prop r blad op ration.

• Ch ck for loos fast n rs.

• Ch ck tir s for prop r inflation. S tir s for maximum inflation. R ar tir valv

st ms ar locat d on th insid of th wh l rim.

DAILY MAINTENANCE

Mak sur all nuts and bolts ar tight and cott r pins and r tain r springs ar s cur .

K p your blad s sharp. Obs rv all saf ty pr cautions.

BLADE CARE AND SERVICE

For b st r sults blad s must b k pt sharp. Th blad s can b sharp n d with a f w strok s of a

fil or grinding wh l. Do Not att mpt to sharp n blad s whil th y ar on th machin .

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure nuts are

tight.

SAFETY AND OPERATIONAL DECALS

R plac d cal imm diat ly if damag d. Ord r by part numb r from Swish r.

20076-SWISHER USA FLAG

OD55 - DANGER

OD45 - WARNING DECAL

21446 - GEAR SELECTION

OD99125 - MEDIUM LOGO WHITE

OD99156 - SMALL LOGO WHITE

DECALS NOT SHOWN

19722-- Pr dator Talon LH D cal

19732-- Pr dator Talon RH D cal

OD85--Pr dator LH D cal

OD86--Pr dator RH D cal

OD87– Rugg d Cut 24 4SP Trans Whit D cal

20000--Comm rcial Pro D cal

18971 - SPARK ARRESTOR

WARNING

OD28- KEY SWITCH

21299 - CALIFORNIA PROP 65

19988 - MADE IN

MISSOURI, USA

19898 - THROTTLE

䉆

ITEM # DESCRIPTION PART #

1 Guard - Engine, Cover 19888*

2 Guard - Engine, Right 20595*

3 Bolt - Serr Flange 5/16-18 X 3/4 NB596

4 Clip - Tinnerman 5/16-18 3706

5 Guard - Engine, Left 19885*

6 Guard - Engine, Front 19884*

7 Strap - Battery, 9" AS013

8 Hook - Battery Strap AS049

9 Battery (Not In luded) N/A

10 Pad - Battery BATPAD

11 Bolt - Serr Flange, 5/16-18 X 1 10548

12 Cover - Belt 19889*

13 Nut - Serr Flange 5/16-18 NB170

14 Channel - Side, Right 19211*

15 Channel - Side, Left 19212*

16 Clip - Nylon 1/2" NB683

17 Bolt - Serr Flange, 5/16-18 X 2 1/4 NB622

18 Mount - Handle Height Adjust 19214*

19 Cover - Rear Frame 21439*

ASSEMBLY PARTS DETAIL

WRC10224HC MODEL SHOWN WITH CASTERS

Wh n ord ring r plac m nt parts

*USE PAINT CODE: TK=BLACK

BATTERY NOT INCLUDED:

REQUIRES A 12V LAWN AND GARDEN

BATTERY WITH A 230 MIN CCA. U1 GROUP

FOR CORRECT FIT.

SEE PAGE 14

FOR DETAILS

SEE PAGE 13-14

FOR DETAILS

SEE PAGE 16

FOR DETAILS

SEE PAGE 15

FOR DETAILS

SEE PAGE 11-12

FOR DETAILS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher Z-MAX ZT2560 Bedienungsanleitung

Swisher

Swisher COMMERCIAL PRO Bedienungsanleitung

Swisher

Swisher T6012V Bedienungsanleitung

Swisher

Swisher FT1150 Bedienungsanleitung

Swisher

Swisher PREDATOR TALON WBRC11524C Bedienungsanleitung

Swisher

Swisher PREDATOR Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher ZT13536, ZT17542B, ZT20050 Bedienungsanleitung

Swisher

Swisher FC11544BS Bedienungsanleitung

Swisher

Swisher FC10544BSXP Bedienungsanleitung

Swisher

Swisher Response Commercial Pro ZTR2766CP Bedienungsanleitung

Swisher

Swisher RT1250E Bedienungsanleitung

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Swisher

Swisher ST67522CC Bedienungsanleitung

Swisher

Swisher ST50022STDQ Gebrauchs- und Pflegehandbuch

Swisher

Swisher POSTMASTER PST67522 Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher ZT2452 Bedienungsanleitung

Swisher

Swisher ZTR2760BS Bedienungsanleitung

Swisher

Swisher ZT2760B Bedienungsanleitung

Swisher

Swisher Ride King Bedienungsanleitung

Swisher

Swisher ZT2766 Bedienungsanleitung

Swisher

Swisher QUADBOSS QBFC1966 Bedienungsanleitung

Swisher

Swisher Trim-Max STD4422HO Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung