Symbol LS-2100U Bedienungsanleitung

Installation

Installing the Keyboard Wedge Reader

To install a keyboard wedge reader, follow the steps below:

1. Turn off the power of the PC or Terminal.

2. Unplug keyboard from the PC or Terminal.

Make sure you have the Y cable with appropriate

connector type for your PC or Terminal.

4. Connect Scanner to your PC or Terminal.

Connect the keyboard connector to the female connector

of the Y cable

6. Turn on the power of PC or Terminal.

Installing the RS232 Reader

To install a RS232 reader, follow the steps below:

1. Turn off the power of the PC or Terminal.

Make sure the connector type from RS232 to the PC or

Terminal is correct.

3. Plug ACAdaptor connector into connector of the reader.

4. Turn on the power of PC or Terminal.

5. Setup the Interface of the reader to RS232 mo

de by

scanning the barcode in the Interface Selection.

Method of Programming

Loop of programming

The philosophy of programming parameters has been show on

the flow chart. Basically user should

1. Scan Start of Configuration.

2. Scan all necessary labels for parameters that meet

applications.

3. Scan End of Configuration to end the programming.

4. To go bark to the Default Settings, just scan label for Set

All Defaults.

Factory Default Settings

The factory default settings are shown with < >and bold in the

following sections. You can make your own settings by following

the procedures in this manual.

By scanning” Set All Default” label, the settings will go back to the

factory default settings.

Setup Commands

Set All efaults

Set all the parameters to the

factory default setting.

Start Configuration.

End Configuration.

Abort Configuration

Terminate current programming

status.

Version Information

Display the decoder version

information and date code

Interface Selection

RS232 Mode

USB Mode

Start Configuration Abort Configuration

Reading Mode

<Good Read Off> Flash-On

Trigger On/Off

Continuous/Trigger Off Testing

Continuous/No Trigger

Trigger ON/Good Read Off/Delay=??

*This mode is almost the same as

<Good Read OFF> but you can delay

time for turning off LED<Default is 3

seconds> you can use the provided

Decimal and Hex-Label Tables for you

own setup.

Trigger On/Good Read

Off/Delay=??

Continuous/Trigger Off/Delay=??

*This mode you can define the delay

time to control the LED off after

releasing the trigger.

Continuous/Trigger Off

End Configuration

RS-232 Communication Parameters

Set Up BAU Rate

300 <9600>

600 19200

1200 38400

2400

4800

Start Configuration Abort Configuration

RS-232 Communication Parameters

Set Up ata Bits:

7 Data Bits

<8 Data Bits>

Set up Parity:

<None>

Even

Odd

End Configuration

RS-232 Communication Parameters

Handshaking

<None>

RTS/CTS Enable

ACK/NAK Enable

XON/XOFF Enable

Start Configuration Abort Configuration

RS-232 Communication Parameters

(ACK/NAK Response Time CTS Observation Time:)

ACK/NAK Time Out=??

Scan Start Configuration Label

Scan ACK/NAK Time-out Label

Scan Two Digit Labels in Table–Hex

Scan Confirm Label in Table-Hex

Scan End Configuration Label

RTS/CTS Time Out=??

Scan Enter Start Configuration Label

Scan RTS/CTS Time-Out Label

Scan Two Digit Labels in Table–Hex

Scan Confirm Label in Table-Hex

Scan End Configuration Label

RTS Signal status:

Normal LOW <Normal High>

End Configuration

Inhaltsverzeichnis

Andere Symbol Barcode-Lesegerät Handbücher

Symbol

Symbol LS 1220 Installations- und Betriebshandbuch

Symbol

Symbol LS4000P Series Bedienungsanleitung

Symbol

Symbol LS 4208 Bedienungsanleitung

Symbol

Symbol LS4278 Bedienungsanleitung

Symbol

Symbol LS3578-FZ20005WR Bedienungsanleitung

Symbol

Symbol LT 1806 Installations- und Betriebshandbuch

Symbol

Symbol SE 2223 Kurzanleitung zur Einrichtung

Symbol

Symbol LS 9100 Installations- und Betriebshandbuch

Symbol

Symbol 3366 Bedienungsanleitung

Symbol

Symbol LS 6800 Bedienungsanleitung

Symbol

Symbol LS-3203ER Installations- und Betriebshandbuch

Symbol

Symbol LT 1810 Bedienungsanleitung

Symbol

Symbol LT 1804 Installations- und Betriebshandbuch

Symbol

Symbol LS1203 Bedienungsanleitung

Symbol

Symbol LS3578 Bedienungsanleitung

Symbol

Symbol DS3508 Bedienungsanleitung

Symbol

Symbol LS 2000MX series Bedienungsanleitung

Symbol

Symbol LS3578 Bedienungsanleitung

Symbol

Symbol P360 Bedienungsanleitung

Symbol

Symbol LS4000P Series Installations- und Betriebshandbuch

Symbol

Symbol LS 4008i Bedienungsanleitung

Symbol

Symbol LS 3408 Bedienungsanleitung

Symbol

Symbol Series 3800 Bedienungsanleitung

Symbol

Symbol TC70 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung