Symbol LS 3020 Betriebsanleitung

LS 3020-I037A Special Operating Instructions

(70-04014-37)

Revision A: March 1994

Special Operating

Instructions



LS 3020-I037A Special Operating Instructions

(70-04014-37)

Revision A: March 1994

2-4

This version of the software enables the scan-

ner to verify that the Motorola terminal is

ready before attempting a decode.

Defaults

Baud Rate: 2400

Stop Bits: 1

Laser Enable Mode: Disable

Laser Enable Mode

The Laser Enable Mode parameter indicates

whether the LS 3020 must establish communi-

cation with the Motorola terminal prior to at-

tempting a decode. If this parameter is

enabled, the following sequence occurs when

the trigger is pulled:

• The scanner sends an ENQ (05H) to

the terminal.

• ThedecodeLEDﬂashestoindicatethe

scanner is waiting for acknowledg-

ment from the terminal. The LED

stops ﬂashing when ACK (06H) or

NAK (15H) is received, or the trigger

is released.

• If an ACK is received, the unit at-

tempts a decode.

• If a NAK is received, the unit issues

four short low beeps.

LS 3020-I037A Special Operating Instructions

(70-04014-37)

Revision A: March 1994

3-4

Aiming LEDs andTrigger Posi-

tions

The LS 3020-I037A does not generate an aim-

ing LED.

An aiming LED is provided for the

LS 3020LR-I037 or LS 3020ALR-H037 when

the trigger is pulled. These scanners support

a two-position trigger to allow the user to aim

prior to activating the motor.

Whenthetriggerispulledintheﬁrstposition,

the aiming LED is generated. If the trigger is

not pulled to the second position, the aiming

LED turns off after approximately two sec-

onds.

Triggering and Laser Enable

Mode

If the Laser Enable Mode is disabled, the scan-

ning motor is activated as soon as the trigger

is pulled to the second position.

If Laser Enable Mode is enabled and the trig-

ger is not pulled to the second position, the

aiming LED remains on for two seconds, and

the unit does not transmit an ENQ. If the trig-

ger is pulled to the second position, the unit

transmits the ENQ to the terminal.

• If an ACK is received, the unit at-

tempts a decode.

• If a NAK is received, the aiming LED

is turned off, and the unit issues four

short low beeps.

• If the unit does not receive anACK or

NAK, the aiming LED remains on for

two seconds. The decode LED contin-

ues to ﬂash until anACK or NAK is re-

ceived.

LS 3020-I037A Special Operating Instructions

(70-04014-37)

Revision A: March 1994

4-4

Laser Enable Mode

To enable or disable this parameter:

1. Scan the

ENABLE LASER MODE

bar

code.

2. Scan either

ENABLE

DISABLE

3. Scan

ENTER

ENABLE LASER MODE

ENABLE

DISABLE

ENTER

Inhaltsverzeichnis

Andere Symbol Barcode-Lesegerät Handbücher

Symbol

Symbol SYMBOL LS7808 Bedienungsanleitung

Symbol

Symbol LS 9208 Bedienungsanleitung

Symbol

Symbol LS1900 Series Bedienungsanleitung

Symbol

Symbol DS 3408 Installations- und Betriebshandbuch

Symbol

Symbol LS3578 Bedienungsanleitung

Symbol

Symbol LS 6800 Bedienungsanleitung

Symbol

Symbol Phaser P460 Installations- und Betriebshandbuch

Symbol

Symbol LS 9208 Bedienungsanleitung

Symbol

Symbol LS4000P Series Installations- und Betriebshandbuch

Symbol

Symbol MiniScan Series Bedienungsanleitung

Symbol

Symbol M2004-I418 Betriebsanleitung

Symbol

Symbol Symbol LS2208 Bedienungsanleitung

Symbol

Symbol MiniScan MS-220X Kurzanleitung zur Einrichtung

Symbol

Symbol LS 9100 Installations- und Betriebshandbuch

Symbol

Symbol SYMBOL MINISCAN MSXX04 Kurzanleitung zur Einrichtung

Symbol

Symbol LS3008 Bedienungsanleitung

Symbol

Symbol P360 Bedienungsanleitung

Symbol

Symbol Symbol LS2208 Installations- und Betriebshandbuch

Symbol

Symbol DS4308 Installations- und Betriebshandbuch

Symbol

Symbol LS9203 Installations- und Betriebshandbuch

Symbol

Symbol LS 2100 Series Bedienungsanleitung

Symbol

Symbol LS 2000MX series Bedienungsanleitung

Symbol

Symbol LT 1804 Installations- und Betriebshandbuch

Symbol

Symbol Keychain Barcode Scanner Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung