Symbol LS 3070 Bedienungsanleitung
LS 3070 Scanner
LS 3070 Scanner
1997-1999 SYMBOL TECHNOLOGIES, INC. All rights reserved.
Symbol reserves the right to make changes to any product to improve reliability,
function, or design.
Symbol does not assume any product liability arising out of, or in connection with, the
application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under
any patent right or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which Symbol products might be used. An
implied license only exists for equipment, circuits, and subsystems contained in Symbol
products.
Symbol is a registered trademark of Symbol Technologies, Inc. Other product names
mentioned in this manual may be trademarks or registered trademarks of their
respective companies and are hereby acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, N.Y. 11742-1300
http://www.symbol.com
Patents
This product is covered by one or more of the following U.S. and foreign Patents:
U.S. Patent No.4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831; 4,593,186;
4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,816,660;
4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833;
5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520;
5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904;
5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792;
5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164;
5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361;
5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081;
5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231;
5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002;
5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889;
5,552,592; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531;
5,619,028; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800;
5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,745,794; 5,754,587; 5,762,516;
5,763,863; 5,767,500; 5,789,728; 5,808,287; 5,811,785; 5,811,787; 5,815,811;
5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,850,078; 5,861,615; 5,874,720;
5,875,415; 5,900,617; 5,902,989; 5,907,146; 5,912,450; 5,914,478; 5,917,173;
5,920,059; 5,923,025;D305,885; D341,584; D344,501; D359,483; D362,453;
D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581.
Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875;
1,955,269 (Japan).
European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/
03938; Italy 1,138,713.
rev. 7/99
1
Quick Reference
Scanner Varieties
The LS 3070 scanners include a wide variety of scanning types,
optimized for particular applications. The varieties are the
following:
• Standard - for most Class II scanning applications, in which
symbol density (5 to 55 mil) and range (0 - 35 in.) fall within
relatively normal ranges.
• Long Range (LR) - for Class II applications with short range
reading on medium density symbols and long range reading
on low density symbols.
• Advanced Long Range (ALR) - for long range reading on me-
dium and low-density symbols, optimized by the increased
power of the Class IIIA laser.
• Extra Long Range (XLR) - for scanning ranges of up to 180
inches (457 cm) on 55 mil symbols, also using a Class IIIA la-
ser.
• High Visibility (HV) - for scanning ranges up to 33 inches (86
cm) on 55 mil symbols, and ambient sunlight up to 10,000 ft.
candles, using a Class IIIA laser.
2
LS 3070 Scanner
Setup
1. Identify System Components
2. Connect Cable to the Base/Charger Unit
This procedure depends on which host terminal is used. For
complete details per terminal type, refer to the RL 470 Base Station
Interface portion of the LS 3070 Product Reference Guide.
3. Attach Power Supply
Connect the power supply to the power input port on the rear panel
of the LS 3070 base/interface/charger.
Connect the power supply to a receptacle supplying AC power of
the proper voltage level.
RL 470 Base/Interface/
Charger Unit
LS 3070
Scanner
Power Supply
Power Supply
Connection Port
Host
3
Quick Reference
4. Insert Scanner Into Base/Charger and Charge the
Battery
Before its first use, the LS 3070 battery must be charged.
After the power supply has been connected, insert the scanner into
the base/charger cradle as follows.
a. Place the nose of the scanner into the large rectangular re-
ceptacle of the base/charger.
b. Then place the handle of the scanner into the opening of
the smaller latched receptacle.
c. Press down firmly until the bottom of the handle seats
snugly into the receptacle and engages the latch.
Caution: Use of excessive force in placing the scanner into the
base can damage the charging contacts on the scanner or
base. Such damage can interfere with or prevent charg-
ing of the scanner’s batteries by the base.
Check the charge-status indicator LED; it stays steadily on while the
battery is charging and blinks rapidly when the battery is fully
charged. Full charge takes less than two hours.
To remove the scanner from the base/charger, grasp the handle of
the scanner and lift the bottom of the handle out of the latched
receptacle, thereby freeing the scanner from the base.
Caution: Trying to remove the scanner nose first, instead of han-
dle first, can break the latch in the base receptacle.
4
LS 3070 Scanner
5. Set Address of the Base/Charger
The base/charger must be assigned an address, with a value between
01 and 7E.
Caution: Each base station must have a unique address.
The unique address of the base determines the initial frequency on
which the base and the scanner communicate. To minimize possible
interference between systems, bases which are close to each other
should be assigned sequential addresses.
Set the address through setting the two rotary dials, located by
opening a panel on the base/charger’s underside. Turn the base/
charger upside down, open the panel, and notice two rotary dials.
5
Quick Reference
The first is a 10-position (0 to 9, high order address digit) and the
second a 16-position (0 to F, low order address digit). Digits are
printed sequentially around each circle. Note that positions 8 and 9
are illegal on the 10-position switch.
Set the desired address with a small screwdriver; possible addresses
are listed on the next page. Note that too large a screwdriver can
damage the switches.
When the address is set, close the panel, turn the base/charger
rightside up again.
Possible Base/Charger Addresses
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F
20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F
30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F
50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F
60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F
70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E
Rotary Switches
0
0
High Order Low Order
10 Position 16 Position
Insert Screwdriver in Slot
6
LS 3070 Scanner
6. Pair Scanner with Base/Charger
The wireless “connection” between the scanner and base/charger is
the low power radio transmission through RF transceivers in the
both the scanner and base/charger. The actual communication
consists of bidirectional message packets. However, the scanner and
base/charger must be paired for this communication to work
between the two devices.
To pair the scanner with the base/charger:
•ScanthePAIRING bar code on the next page or on the RL 470
base.
• Then insert the scanner into the base/charger’s cradle. You
have 15 seconds to do this, or there will be error beeps (4
beeps = unsuccessful pairing or base not powered). Note that
you cannot scan data until this linking is complete.
• At that time, through the scanner’s contact shoe, there is an
exchange of information (addressing, RF channels, etc.) be-
tween the scanner and the base/charger’s cradle. This occurs in
less than a second.
PAIRING
7
Quick Reference
• After that exchange, the scanner and base/charger are paired.
Successful pairing is indicated by as warble beep; failure, or
unsuccessful link, is indicated by a Lo Lo Lo Lo beep.
7. Set Host Type
Each Interface Cable Assembly defaults to a given host. Below is a
list of the assemblies and their corresponding default hosts. If you
wish to change the type of host, find and scan the proper bar code
on the following pages.
Cable Assy. Default
IK-0100, -0101 IBM 4683/93 Port 5B; 4683/84 Port 17
IK-1005, -1006 ICL 9505, 9507, 9518; 9520 OCIA
IK-0200 IBM 3683, 3684 Keybd Wedge
IK-0300 IBM 3653 Kybd Wedge
IK-0400 IBM PC/AT, Telex Memorex Kybd Wedges
IK-0401 IBM PS/2 - 30, 50, 55SX, 60, 70, 80
IK-0402, -0403 NCR 7052 Wedge; Fujitsu 9000 Wedge
IK-0406, -0409 IBM 3161/319X; IBM 3151, 347X Wedges
IK-0413 Wyse 50 Wedge
IK-0500 NCR 2152 Tel Kybd Wedge
IK-0600 NCR 2151 Tel Kybd Wedge
IK-0700 NCR 280 Kybd Wedge
IK-0800 — 0803 Standard RS-232C
IK-0900 Fujitsu 9000 OCR
IK-0901 Fujitsu 7770, 7880, 7990, 8770 OCR
IK-0902 IBM 3653, 3683/3684 OCR
IK-1001, -1002 NCR 2152, 2257, 2950; 215X, 7050 OCIA
IK-1003, -1004 Nixdorf 8812 OCIA; NCR 2126-1120 OCIA
IK-1100 IBM 4683/93 Port 9B
IK-1200, -1201 IBM 3178; IBM 3278 Wedges
IK-1300 Wyse 60, 85, 150, 160, 185 Wedges
IK-1301 HP 7000/XX, 239X Wedges
IK-1400 DEC VT 2XX/3XX/4XX Wedges
IK-1500, -1501 Dual RS-232C
8
LS 3070 Scanner
Single Port RS-232
Dual Port RS-232
In some cases, two bar codes may correspond to one interface type;
this happens when different software revisions exist for the same host type.
If there are two bar codes for your host type, try the first bar code; if that
does not work, then try the second one.
Four Options for Dual Port RS-232 Follow
For IK-1500, Port 1 = Male, TxD on Pin 2; Port 2 = Female, TxD on Pin 3.
For IK-1501, Port 1 = Male, TxD on Pin 3; Port 2 = Female, TxD on Pin 2.
Andere Handbücher für LS 3070
1
Inhaltsverzeichnis
Andere Symbol Barcode-Lesegerät Handbücher
Symbol
Symbol LS1900 Series Bedienungsanleitung
Symbol
Symbol SE 923 Kurzanleitung zur Einrichtung
Symbol
Symbol LS4278 Installations- und Betriebshandbuch
Symbol
Symbol CSM 150 Bedienungsanleitung
Symbol
Symbol Symbol LS2208 Installations- und Betriebshandbuch
Symbol
Symbol LS4278 Bedienungsanleitung
Symbol
Symbol US AUTOMATION EP-1 Bedienungsanleitung
Symbol
Symbol LS 2104 Installations- und Betriebshandbuch
Symbol
Symbol SE955 Kurzanleitung zur Einrichtung
Symbol
Symbol LS-2100U Bedienungsanleitung
Symbol
Symbol Symbol LS2208 Installations- und Betriebshandbuch
Symbol
Symbol LS4000P Series Bedienungsanleitung
Symbol
Symbol DS 3408 Installations- und Betriebshandbuch
Symbol
Symbol LS2208-SR20001R Bedienungsanleitung
Symbol
Symbol DS3478 Installations- und Betriebshandbuch
Symbol
Symbol LS6004i-I000 Bedienungsanleitung
Symbol
Symbol MiniScan Series Bedienungsanleitung
Symbol
Symbol LS3578 Bedienungsanleitung
Symbol
Symbol LS 6005i Installations- und Betriebshandbuch
Symbol
Symbol P470 Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
