TA Instruments TMA 2940 Bedienungsanleitung
TMA 2940/Q400 Packup instructions
Back to Thermal Menu
1. Remove the probe and stage from the instrument.
2. Remove the outer cover around the shuttle assembly.
3. Remove the weight tray. Tape the nylon screw in place and lay the weight tray in
the top of the furnace. (Fig 1 & 2).
Weight Tray
N
ylon Screw
Figure 1
Figure 2
Ehc 1 of 1
Back to Thermal Menu Back to Top
TMA 2940/Q400 Packup instructions
Back to Thermal Menu
4. Remove the 8 shoulder screws from the front support bracket. (Figure 3).
Shoulder bolts (8)
Front Support
Rear Supports (2)
Outer Clamp
Figure 3
5. Carefully slide the front support bracket between the upper and lower
suspensions, behind the weight tray mounting bracket (Fig. 5)
Front Support
Upper Suspension
Lower Suspension
Figure 5
Ehc 2 of 2
Back to Thermal Menu Back to Top
TMA 2940/Q400 Packup instructions
Back to Thermal Menu
6. Carefully slide the rear supports between the upper and lower suspensions. (Fig 7)
Rear Supports
Shuttle Lift Arm
Figure 7
7. Install the shoulder bolts through the front support bracket and thread them into
the rear support brackets (Fig 8).
Shoulder bolt
Figure 8
Ehc 3 of 3
Back to Thermal Menu Back to Top
TMA 2940/Q400 Packup instructions
Back to Thermal Menu
8. Remove one of the bolts from the outer clamp and install the outer clamp. The
clamp should go above and below the upper and lower suspensions. (Fig 9)
Outer Clamp
Upper Suspension
Lower Suspension
Figure 9
Ehc 4 of 4
Back to Thermal Menu Back to Top
TMA 2940/Q400 Packup instructions
Back to Thermal Menu
9. Install the bolt in the other end of the outer clamp and tighten. (Fig 10).
10. The suspension should now be immobilized.
Figure 10
11. Install the rear shipping foam support under the lower weights. (Fig 11)
Shipping Foam Lower Weights
Figure 11
Ehc 5 of 5
Back to Thermal Menu Back to Top
TMA 2940/Q400 Packup instructions
Back to Thermal Menu
12. Lower the furnace. Tape the weight tray into the top of the furnace.
13. Place the cardboard sleeve over the furnace lift shaft. (Fig 12 & 13)
Lockdown Cap Cardboard Sleeve
Figure 12
Figure 13
Ehc 6 of 6
Back to Thermal Menu Back to Top
TMA 2940/Q400 Packup instructions
Back to Thermal Menu
14. Tighten the lockdown cap into the top of the furnace lift shaft. This will
immobilize the furnace.
15. If this is a 2940, turn off the power switch. If this is a Q400, go to the next step.
16. On the Q400 display panel, press the “Display Menu” button.
17. Press the “Shutdown” button. Wait for the display screen to show that the
instrument is shutdown and it is safe to turn off the instrument.
18. Turn off the power switch located on the back of the instrument near the power
cord.
Back to Top
2940:
19. Remove the instrument feet and place the instrument on the shipping plywood.
20. Secure the instrument to the plywood with the long ¼-20 bolts provided.
21. Place the board with the instrument attached into the shipping box.
22. Place the inner sleeve inside the box.
23. Seal box and place the green return label on the outside of the box.
Q400:
24. Bolt the Q400 down on the shipping pallet. Place the cardboard box over the
pallet.
25. Strap the cardboard box down over the pallet and instrument.
26. Seal the box and place the green return label on the top of the box.
Ehc 7 of 7
Back to Thermal Menu
Andere Handbücher für TMA 2940
1
Dieses Handbuch passt für folgende Modelle
1
Andere TA Instruments Messgerät Handbücher
TA Instruments
TA Instruments TMA 2940 CE Bedienungsanleitung
TA Instruments
TA Instruments DISCOVERY XENON FLASH Bedienungsanleitung
TA Instruments
TA Instruments DHR Series Bedienungsanleitung
TA Instruments
TA Instruments TGA 2950 Bedienungsanleitung
TA Instruments
TA Instruments Nano ITC Series Bedienungsanleitung
TA Instruments
TA Instruments TGA 2050 Bedienungsanleitung
TA Instruments
TA Instruments ARES-G2 Bedienungsanleitung
TA Instruments
TA Instruments DHR Series Bedienungsanleitung
TA Instruments
TA Instruments TMA 2940 Bedienungsanleitung
TA Instruments
TA Instruments TMA Q400 Bedienungsanleitung
