Tapco MX Series Bedienungsanleitung
MX Series™
Operating Instructions
MX 8™• MX 10™• MX 12™• MX Stand™ • MAX Cut-Off™
Snap StandMX Series™
2
Item# Description Item# Description Item# Description
MX Series™Brake Parts List
10491 8'6" Stainless Edge
10492 10'6" Stainless Edge
10493 12'6" Stainless Edge
10504 12'6" Tape Measure
10505 10'6" Tape Measure
10506 8'6" Tape Measure
10519 ¼-20 x ¾" Hex Wash HD Sc
10534 3/8" Flat Washer
10535 3/8-16 Nylock Hex Nut
10887 T-Handle Hex Key
11396 Pivot Link Assembly Kit (6)
11397 ¼" x 1 ¼" Faspin Kit (4)
11398 Locking Handle Plug Kit
Locking Handle Plug
3/8-16 x 2 ¼" Bolt
11400 Locking bar Pin Kit
10 pins, 20 keepers
11531 Lifting Handle Cap
11533 Back Rail Cap
13144 C Castings
14144 Pivot Arm - Left
14145 Pivot Arm - Right
14253 8-32 x 5/16" Phil Pan HD Sc
14254 8-32 x 1" Phil Pan HD Sc
14256 ¼-20 x 1" FL HD Sc
14257 3/8-16 x 5" Hex Cap Bolt
14263 8'6" Rubber Strip
14264 10'6" Rubber Strip
14265 12'6" Rubber Strip
14266 8'6" Wear Strip
14267 10'6" Wear Strip
14268 12'6" Wear Strip
14271 Lifting Handle Support Bracket (2)
14273 Moving Hinge Cap
14274 Locking bar Cap
14276 Fixed Hinge Endcap
14299 8'6" Locking bar
14300 10'6" Locking bar
14301 12'6" Locking bar
14311 8'6" Back Rail
14312 10'6" Back Rail
14313 12'6" Back Rail
14353 8'6" Locking Anvil
14354 10'6" Locking Anvil
14355 12'6" Locking Anvil
14374 Lifting Handle Assembly
14387 8'6" Fixed Hinge
14388 10'6" Fixed Hinge
14389 12'6" Fixed Hinge
14390 8'6" Moving Hinge
14391 10'6" Moving Hinge
14392 12'6" Moving Hinge
14414 Locking handle Assembly
14456 MX Series™ Brake Parts Bag 8'
14457 MX Series™ Brake Parts Bag 10'/12'
14480 Bolt and Nut Kit
¼-20 x 4 ½"" Bolt (5)
¼-20 x Nylok Nut (5)
Snap StandMX Series™
3
Setting up the MX Series™Brake
Faspin
Locking Bar
Handle
Plug
Locking
Handle
Hex Bolt
MX Locking Bar Assembly includes:
(2) Locking bars,
(4) Handle Plugs, (4) Faspins, (4) Hex Bolts
1. Insert Hex Bolt through Locking bar
of your MX Series™ Brake and into the
base of Locking bar(s) as indicated us-
ing the 3/8" Hex Bolts provided. HAND
TIGHTEN ONLY. Repeat for other side.
2. Attach the Locking bar over the Handle
Plugs and secure them with Faspins.
Now tighten the 3/8" Hex Bolts with a
9/16" wrench. Handle can be detached
from now on by simply removing the
Faspins.
1. First insert one end of the Handle Plug
into Lifting / Bending Handle and install
Faspin through holes.
2. Next, insert Handle Assembly into hole
in bottom of Moving Hinge. Align hole
in hinge with Handle Plug and insert
screw using Phillips Screw Driver as
shown. Secure with 1/4-20 Lock Nut
Repeat for other handles. To remove
handles, simply remove Faspins. Al-
ways use more than one handle when
bending.
Locking bar Installation
Lifting/Bending Handle Installation
Exploded view of
Handle Assembly
Faspin
Handle
Plug
Lifting/
Bending
Handle
1/4-20 x 1 1/2"
Screw 1/4-20
Lock Nut
Moving
Hinge
Secure with
1/4-20 Lock Nut
Snap StandMX Series™
4
Pivot Link Adjustment Instructions
Pivot Link
Stud
Upper
Adjustment
Link
Lower
Adjustment
Link
Pivot Link Assembly
TO TEST
Cut some narrow strips of aluminum or use
strips from stock you will be using and lock
one under each shoe casting as indicated
above. Then lightly pull the material to
determine the tightness and uniformity
of each Pivot Link. If the material can be
moved when the MX handle is locked or if
it requires excessive pressure to lock the
handle down on the material then the Pivot
Arms may need adjustment.
NOTE: All adjustments are made with the
MX Series™Brake in the “open" position.
All adjustments are tested with strips of
material placed in the MX Series™Brake in
the “locked" position.
TO ADJUST
Insert the 3/16" hex wrench into the Pivot
Link Stud through the access hole in the
upper link. Turn 1/4 turn either COUNTER-
CLOCKWISE to INCREASE locking tension
or CLOCKWISE to DECREASE locking
tension.
Repeat test step above to check tension.
TO ADJUST (Optional method)-
As an alternate method you may use a 5/8"
open-end wrench directly on the Pivot Link
Stud by turning 1/4 turn either COUNTER-
CLOCKWISE to INCREASE locking tension
or CLOCKWISE to DECREASE locking
tension.
Repeat test step above to check tension.
IMPORTANT: The Pivot Links on your MX Industrial Brake have been pre-set at the factory for average holding capacity and ease of
operation. However, it's important that you readjust your MX Industrial Brake to your stock thickness. Your MX Series™ Brake may
also need periodic adjustment due to extreme weather and/or working conditions. It is important that you follow these steps when you
adjust your MX Series™ Brake to ensure proper gripping tension and maximum performance.
First check the uniformity of the clamping pressure along the entire length of your MX Series™Brake by using the following method.
Decrease
Increase
Snap StandMX Series™
5
MX Stand™Parts List
14279
14284
14318 (large stand) *
14320
10539 14321
11533
14316 (large stand) *
14394
14285
14319
10795
10539 ¼” x 1 ¼” Faspin
10795 3/8-16 x 2 ½ T-Knob
11533 Back Rail Endcap
14279 Stand Counter Balance Bracket
14284 Right Stand Leg Assembly
14285 Back Rail Clamp
14316 Rear Cross Tube (large stand)
14318 Front Support Tube (large stand)
14319 Back Rail Clamp Wedge
14320 Stand Counter Balance Plank
14321 Toggle Pin
14394 Left Stand Leg Assembly
14402 Front Support Tube (small stand)
14403 Rear Cross Tube (small stand)
Item# Description
Snap StandMX Series™
6
MX Stand™Set-up
STEP 1
Attach Stand Counter Balance Brackets to
Plank with Carriage Bolts and Nylock Nuts
using a 7/16" Socket or Open end Wrench.
Counter Balance is required for operation.
Stand Counter
Balance Bracket
Stand Counter
Balance Plank
Hardware Requirements: (2) 7/16" & (2) 9/16" Open end wrench.
Right Stand
Leg Assembly
Left Stand
Leg Assembly
3/8-16 x 2 3/4" Hex Hd Bolt
3/8" Flat Washer
3/8" Lock Washer
3/8" Nylock Nut
STEP 2
Slide Stand Counter Balance Assembly up
to the Stand Legs. Insert the 3/8-16 x 2 3/4"
Hex Bolts through the Stand Counter Bal-
ance Bracket and Leg as shown in Figure
2. Use a 9/16" wrench to tighten down 3/8-
16 Nylock Nut.
STEP 3
Insert Front Support Tube through both
Right and Left Legs as shown in Figure 3.
Next slide the 1/4-20 x 2 1/2" bolt through
the Stand Leg and Support tube. Use the
7/16" wrench to secure the Support Tube
in place with 1/4-20 Nylock Nuts.
1/4-20 x 3/4" Carriage Bolt &
1/4-20 Nylock Nut
Stand Counter
Balance Assembly
Snap StandMX Series™
7
Rear Cross
Tube Assembly
MX Stand™Set-up
STEP 4
Rotate the Toggle Pin 90 degrees and
slide the Rear Cross Tube onto the
Pin. To secure the Tube in place allow
the arm on the Toggle Pin to drop
down. Repeat steps in all locations.
Toggle Pin (unlocked)
Rotate arm on Toggle Pin
to insert Rear Support Tube. Toggle Pin in
Locked position.
Toggle Pin (locked)
Snap StandMX Series™
8
Installing a MX Series™Brake on MX Stand™
STEP 5
Align the hole in the Fixed Hinge with the Slot on the Stand Top
Bracket. See 5a.
Insert Faspin through the Stand Top Bracket and into the Fixed
Hinge to secure Brake in place. See 5b.
The Brake must be secured with Faspins on the Left & Right
Stand Leg Assemblies.
Using 2 people, set Brake on Stand with the hinges above the
Front Support Tube.
3/8-16 Knob
STEP 6
Place Back Rail Clamp on the Back Rail. Slide Knob through
the Wedge and turn clockwise into the Threaded Insert.
See 6.
Back Rail Clamp Assembly must be attached on Left and
Right Stand Leg Assemblies.
5b
5a
6
Stand Back Rail
Clamp Wedge
Stand Back
Rail Clamp
Removing a MX Series™Brake from MX Stand™
- Removing the brake from the MX Stand is essentially the opposite of attaching it to the stand.
- Remove the Back Rail Clamp Assembly from the Stand.
- Lift the Moving Hinge and remove the Faspins and place in the Stand Leg Faspin storage hole.
Snap StandMX Series™
9
Adjustable MAX Cut-Off Parts
6
10013
10021
10227
12263
12264
ASSEMBLY
10227
ASSEMBLY
10020
10225
10015
11409
12396
10008
10021
12293
* This kit replaces the Track Bearing Kit 11393. Both are
still available for purchase.
** Please contact Customer Service if these parts need to
be replaced.
Item# Description
10008 Handle
10013 1/4-20 X 1-1/4” Button Hd Screw
10020 1/4-20 X 5/8” Hex Button HD Screw
10021 1/4-20 X 1” Hex Button Hd Screw
10225 Bridge
10227 MAX Knife Assembly**
10349 Coupling Nut (hook, not shown)
10519 1/4-20 X 3/4” Hex Wash Hd Screw
(not shown)
11393 Track Bearing Kit (not shown)
(2) Track Bearing 10012
11404 Material Stop Kit (not shown)
(2) Material Stop 10740
(2) 1/4-20 Knurled Knob 10776
(2) Cut-Off Tape Measure 10023
Item# Description
11409 Cut-Off Guide Bearing Kit
(2) Guide Bearing 10016
(2) 5/16” Roll Pin 10015
12263 Adjusting Nut
12264 Adjustable MAX Cut-Off Body
12293 1/4-20 X 1 1/2 Socket Head Cap Screws
12396 Flange Track Bearing Kit*
(2) Wide Flange Track Bearing 12334
(2) 1/4-20 X 5/8” Hex Button Hd Screw 12364
Snap StandMX Series™
10
Setup for Adjustable MAX Cut-Off
3. Secure the tape measures in place
by “punching" down the edge of the
pivot arm onto the tape measure. Use a
standard nail set or punch.
IMPORTANT! Read this safety information before using product.
1. Always keep hands and fingers clear of the knives during all phases of use.
2. If using both hands to push tool through material, ensure hands are not in the path of
the exiting material as it leaves the rear area of the tool.
3. Remove cut-off from anvil prior to bending material. Failure to do so can cause the
tool to fall from brake resulting in tool damage or personal injury to user.
4. Never use tool to cut material not firmly clamped in brake.
LIST OF PARTS:
(1) Adjustable MAX Cut-Off
(2) MX Material Stop Kit #14485
1. Slide measuring tapes into Pivot Arm
slots from rear of Pivot Arm till they
stop. Tape measures take into account
1 1/2" difference between the bending
edge and the shear point of Cut-Off for
accurate cuts.
2. Slide material stop onto Pivot Arms
from rear as shown.
Note: Recommended locations are on
the second castings in from each end
of your brake.
Tools Needed for Initial Set Up:
hammer, punch or nail set,
9/16" wrench, Phillips screw driver.
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Tapco Baumaschinen Handbücher
