Taramp's T 0302 FX Bedienungsanleitung

The installation of this product must be made by a qualified professional.

CAR SOUND MIXER

MULTICOLOR

Index

Term of warranty

Technical assistance

For international support, check on our website:

www.taramps.com.br/en/rede-de-assistencias-tecnicas or contact direct the factory support:

Phones: +55 18 3266-4050 / +55 18 99749-3391

E-mail: [email protected]

•Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the

product.

•Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;

•Damaged products by improper installation, water infiltration, violation by unauthorized individuals;

•Cases in which the product is not used in adequate conditions;

•Tamper or torn warranty seal;

•Defects caused by accessories, modifications or features attached to the product;

•The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);

•Warranty card is not properly filled or torn;

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP - Brazil,

ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making,

assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its

original use within 12 months from the date of purchase. In case of defect during the warranty period,

TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Outputs

01 • Term of Warranty

02 • Introduction

• Technical assistance

04 • Product Overview

• Safety

05 • Connections

• Inputs

• Safety requirements

03 • Presentation

• Important recommendations

• Controls

08 • Audio eﬀects table

11 • Installation

10 • Installation

06 • Functions

• Connection examples - 2

• Standby eﬀects table

09 • Installation

• Power and activation

• Connection examples - 1

12 • Technical features

07 • RGB eﬀects

Safety requirements

Introduction

Taramps reserves the right to modify the contents of this document at any time without prior notice and

does not have the obligation to apply the changes in units which were previously produced.

- Use the correct tools for installing this product.

To ensure proper use, please read through this manual before using the car sound mixer. It is

specially important that you know the CAUTIONS contained here.

- The installation of this product must be done by a qualified professional.

- This product is for use with 12V batteries. Always check the voltage before installing.

- Never install the product in places exposed to dust, humidity and water. Pay attention to

install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.

- Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect

any wires routed through car's body.

- Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating

as indicated here in this manual. Use of improper fuse or circuit breaker could result in

overheat, smoke, damage to product, injury or burns.

- Automotive sound systems may produce high sound pressure levels. Avoid continuous

exposure to levels over 85dB to prevent permanent hearing loss.

As you read this manual, pay attention to the safety symbols.

Safety

This symbol with “CAUTION” is intended to alert the user to the presence of

important instructions. Failure to heed the instructions will result in risk of injury

to user or product damage.

CAUTION

Read this manual before installing the product. In case of questions contact our technical

support: +55 (18) 3266-4050 or www.taramps.com.br.

At the end of its lifespan, this product must not be disposed of in household waste.

Look for an electronic equipment collection or recycling center for proper disposal.

Declaration of Conformity

Hereby, Taramps Electronics Ltda declares that the product

T 0302 FX MULTICOLOR complies with the Directive

2014/30/EU, according with the following harmonized

standard:

-EN 50498:2010

The full text of the EU Declaration of Conformity is available at

the Product Page on Internet.

TARAMPS ELECTRONICS LTDA

Alfredo Marcondes - SP

Brazil

Electromagnetic compatibility (EMC) -

Product family standard for aftermarket

electronic equipment in vehicles

With a total of 69 variable lighting eﬀects, causing a diﬀerent visual eﬀect for the user. See

pages 07 and 08.

- Level for output control.

CHANNELS 2 and 3 feature shared L+R type RCA inputs with an RTS connector for greater

connection exibility.

The T 0302 FX MULTICOLOR features 3 input channels, CHANNEL 1 is balanced with two

shared connections, one XLR and one RTS. This is a high-sensitivity, wide-gain input, which

allows the use of a Microphone or LINE IN.

All 3 inputs have independent controls for:

The T 0302 FX MULTICOLOR mixer was designed for sound systems allowing the mixing of

several types of audio signals with high delity, ensuring the original dynamics of the sound.

It features a 4-band equalizer that allows you to increase or reduce specic ranges of mid-bass

and highs, allowing for a professional control in any situation. It also has the Echo FX feature,

which allows you to add the Echo eﬀect to your songs or voice. Its outputs with timed MUTE

avoid undesirable noises (Pops) when turned on or oﬀ, dispensing with the sequencing of

activations, facilitating installation.

- Gain for adjusting the input signal level.

- 4 EQ controls HIGH, MID HIGH. MID LOW and LOW with ±15dB boost/attenuation.

The 2 outputs have great amplitude and can deliver up to +18dBu or 6.3Vac of distortion-free

signal.

In order to avoid noise captation, use good quality

shielded signal cables and connectors.

The sound mixer must be fixed in an easily accessible and

ventilated place. It is not recommended to install the

product on the sides of speakers, as vibrations can

damage their internal components.

Use the P4 adapter with terminal that comes with the

product to connect the power wires to the vehicle's 12V

battery. Use 1.5mm² gauge wires for both the positive and

negative wires. Screw the wires according to the following

instruction:

As protection, a fuse must be installed close to the positive

pole of the battery (1A fuse). check for more details on

pag. 09 of this manual. For the REMOTE connection, use

0.5 mm² wire.

1- Borne on the battery positive

2 - Borne on the battery negative.

Presentation

Important recommendations

Check power polarity and recommended gauge.

it is recommended to install a 1 Ampere fuse on the positive supply terminal.

CAUTION

Pontos de fixação

On this page you have an overview of the T 0302 FX MULTICOLOR sound mixer, you will better

understand the commands on the next page. To be able to use all the product commands, carefully read

all the commands below.

Install the mixer in an easily accessible place and, if fixing is necessary, use the 4 screwing holes to avoid

possible vibrations.

Product overview

Connections

OUT - Outputs

It features an RCA connector in parallel with a connector for TRS. This output mixes all input

signals, including L and R.

This output features a phase inversion button and independent level control, but it also

responds to the MAIN LEVEL control.

AUX OUT

MAIN OUT

This output mixes all input channels, including R and L.

It features an RCA connector in parallel with a connector for TRS.

Unbalanced inputs Inputs for RCA or (TRS 1/4”) connector. They allow you to receive signals

from several types of sound gear such as CD/DVD/MP3-player, audio processors, etc... with

high level outputs.

MIC / LINE

LINE

Balanced inputs for XLR (Canon) and TRS connectors. ATTENTION: these inputs DO NOT

HAVE PHANTON POWER.

IN - Inputs

Functions Controls

Adjusts the input signal level. It must be used in case of input

saturation, signaled by the CLIP LEDs.

Increases or reduces treble by up to ±15dB

Increases or reduces mid-high by up to ±15dB

Increases or reduces mid-low by up to ±15dB

Increases or reduces Low by up to ±15dB

Adjusts the audio level of the channel (channel 1,

2 or 3) that will be mixed at the outputs.

Mutes the channel mixing at the outputs. It is useful for quick channel

cutting without changing the gain settings. When activated, the red CLIP

LED will light regardless of the input signal level.

Red LED shows channel input saturation or MUTE button pressed.

Green LED indicates that the channel is receiving signal at its input.

LED INDICATORS

Indicates the level of the output signal.

Controls the signal level at the outputs.

Inverts the signal phase of the AUX OUT channel by 180°

Adjusts the audio output level at AUX OUT

ECHO FX: The TIME control increases the time between repetitions, ranging

from approximately 50ms to 350ms. The REPEAT control increases the

number of repetitions from 1 (minimum) to 12, with exponential

attenuation.

In a practical way, the TIME control can be compared to the size of an

echo room. For a larger room, the sound takes more time to reflect

on the walls. For smaller rooms the reflection time is short, some

times difficult to realise. The REPEAT control can be compared to the

type of wall coating material. Soft material absorbs more sound

energy, creanting less echo repetition. Hard material reflects more

effectively the sound creating more sound reflection.

ECHO FX

Regulates the amount of effect that will be applied to the

channel. Being 0, no effect and 10, maximum effect.

ECHO FX

ﬁxed color: medium white

ﬁxed color: strong white

palette per function: white gain / eq. blue / eco red / level orange

palette per function: white gain / eq. green / eco red / level orange

palette per function: white gain / eq. purple / eco green / level orange

palette per function: red gain / eq. purple / eco green / level blue

red background with white pimball animation

palette per function: white gain / eq. cyan / eco red / level orange

green background with white pimball animation

ﬁxed color: green + cyan

ﬁxed color: blue

ﬁxed color: pink

ﬁxed color: faint white

ﬁxed color: green

ﬁxed color: cyan

ﬁxed color: purple

ﬁxed color: pink + red

ﬁxed color: yellow

horizontal lines falling and accumulating, changes colors automatically.

vertical back and forth with white background and dots alternating colors.

vertical ﬁll in red.

strobe eﬀect in white

turns oﬀ all RGB eﬀect LEDs

giroﬂex eﬀect

ﬁxed color: red

ﬁxed color: orange

changes the automatic eﬀect randomly

rainbow eﬀect with wave animation

purple background with white pimball animation

blue background with white pimball animation

yellow background with white pimball animation

rainbow background with pimball (arcade) animation in white

cyan background with white pimball animation 07

The T 0302 FX MULTICOLOR sound mixer has several lighting effects that can be chosen by

the user. There are two operating modes that alternate depending on the state of the table:

AUDIO MODE: activated when there is an audio signal output from the table. At this

moment, the RGB EFFECTS button will configure the lighting effect for audio mode.

STANDBY MODE: activated when there is no audio output for 10 seconds. At this moment, the

RGB EFFECTS button will set the lighting effect to standby mode.

NOTE: VU-METER effects are only available in AUDIO MODE. This effect works with the output

audio level and serves only as a lighting effect. For greater output level accuracy, use the LED

VU-METER next to MAIN LEVEL.

RGB EFFECTS

STANDBY EFFECTS TABLE

vu-meter: blue background, scale from blue to red

vu-meter: green background, scale from blue to green

ﬁxed color: green + cyan

ﬁxed color: blue

ﬁxed color: pink + red

ﬁxed color: strong white

palette per function: white gain / eq. green / eco red / level orange

vu-meter: green background, scale from green to red

horizontal lines falling and accumulating, changes colors automatically.

vertical back and forth with white background and dots alternating colors.

vertical ﬁll in red.

ﬁxed color: purple

ﬁxed color: pink

turns oﬀ all RGB eﬀect LEDs

rainbow eﬀects with wave animation

ﬁxed color: orange

strobe eﬀect in white

vu-meter: green background, scale from green to red

VU-meter: purple background, green/yellow/red scale.

vu-meter: white background, range from green to purple

giroﬂex eﬀect

ﬁxed color: red

ﬁxed color: yellow

ﬁxed color: green

ﬁxed color: cyan

ﬁxed color: faint white

ﬁxed color: medium white

palette per function: white gain / eq. blue / eco red / level orange

palette per function: white gain / eq. cyan / eco red / level orange

palette per function: red gain / eq. purple / eco green / level blue

red background with white pimball animation

purple background with pimball (arcade) animation in white

cyan background with white pimball animation

rainbow background with pimball (arcade) animation in white

green background with white pimball animation

blue background with white pimball animation

yellow background with white pimball animation

palette per function: white gain / eq. purple / eco green / level orange

AUDIO EFFECTS TABLE

Power and activation

Installation

Connection that turns on or off automatically from a remote cable from a CD/DVD player. Use 0.5 mm²

cable.

Note: if the ON/OFF button is pressed, the device will not turn off by remote activation.

It can automatically turn on and off by remote activation using the REMOTE IN connection. To do so, keep

the ON/OFF key off (unpressed).

The T 0302 FX MULTICOLOR was designed to be used in car audio systems with a 12V battery, but it can

also be used with an external 12V plug adapter with a current of at least 2A, which must be purchased

separately (in this case, the consumer should pay attention to the adapter plug that should be standard

P4-2mm) . It has an ON/OFF button that eliminates the REMOTE IN connections.

The REMOTE OUT connection can be used for powering amplifiers and is timed to minimize transients

when turning the system on and off.

Output for activating other devices. It can be used to turn on amplifiers or other equipment as long as

they have a remote input. This output is current limited and not suitable for currents greater than 100mA.

Use 0.5 mm² or higher gauge cables.

Turns on the sound mixer regardless of the REMOTE IN signal when pressed.

If the REMOTE IN input is active (remote on) this button will not turn off the device until the REMOTE IN

input is deactivated.

REMOTE IN

REMOTE OUT

POWER ON/OFF

to the battery's 12V positive terminal.

Standard P4 /12V 2mm power connector. Use the TERMINAL/P4 adapter that comes with the product or a

12V adapter source (adapter source doens't come with the product).

Use a 0.75mm² cable for the connections and use a 1A fuse on the positive wire as close as possible to

the battery, following the marking on the TERMINAL/P4 adapter:

to the battery’s negative terminal

12V POWER SUPPLY 03

Check power polarity and recommended gauge.

it is recommended to install a 1 Ampere fuse on the positive supply terminal.

CAUTION

02 03 04

Inhaltsverzeichnis

Andere Taramp's Autozubehör Handbücher

Taramp's

Taramp's HV160.000 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung