Targetti Zedge Pro Bedienungsanleitung
+95°F
-13°F
5.07 lbs
Zedge Pro
WARNING
To ensure a maximum efficient use
of the product, read the instructions
before proceeding installment.
This fixture must be installed by a licensed and
qualified electrician. The installer must comply with
NEC and local building codes when installing the
fixture
Electrical current can cause painful shock, serious
injury, or even death. Make sure you turn off the
power supply, ground fixture(s), and make sure all
electrical connections are correct and secured
tightly
For use in IP66 installations.
Keep the label of the original packaging if any
eventual future claims are needed
Table of Contents
Fixture Dimensions
Distribution of Light
Mounting Diagram
Electrical/Mounting Instructions
Optics Adjusting Instructions
Face Plate Mounting Instructions
Maintenance
Support Page
Pg.2
Pg.2
Pg.2
Pg.3
Pg.4
Pg.5
120-277VAC
Part number: ZEP41FW-
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714)
Pg.6
Pg.7
Fixture Dimensions Distribution of Light
Mounting Diagram
**Diagram not drawn to scale**
Side view of mounted fixture
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714)
7.87"
7.87"
3.70" DEEP
For deep lighting of horizontal surfaces
where the priority is to light open spaces
or wide pathways.
WIDE
For lighting where illuminance uniformity
is essential, for example on long private
or public walkways with wide spaces
between fixtures.
0.35"
SEMI-FLUSH
INSTALLATION
FLUSH
INSTALLATION
Sleeve square ring is
used in flush
installation*
Sleeve square ring is
removed for
semi-flush installation*
*Please refer to the Zedge Pro Installation
Box mounting instruction for details
1
2
Electrical/Mounting Instructions
1. Wiring of the fixture must be done with a
qualified electrician. DO NOT CONNECT
FIXTURE TO LIVE VOLTAGE! The installer
must wire up the line voltage wires and the
dimming wires to the designated power and
dimming cables and secure the wiring
connection with weatherproof connectors
supplied by contractor. The connection of the
fixture to the power and dimming circuit must
comply with NEC and local building code.
2. Once wiring is connected and secured,
it is time to mount the fixture's body into
the sleeve.
a) Installer will insert the fixture's body
inside the sleeve. Installer must be
sure to line up the mounting screw
holes of the sleeve with the fixture's
mounting screw hole when inserting
the body into the sleeve.
b) Once the fixture's body is set,
installer will secure the body onto the
mounting box with two mounting
screws. The installer will make sure
that the installation is tight and the
fixture is pressed and secured inside
the back box.
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714)
D (-)
D (+)
Gray
Purple
Neutral
Ground
White
Green
Line Black
Dimming Cable
Line Voltage Cable
a1
a2
x2
Fixed / Adjustable
Weatherproof connectors
for each wire pair
connection (5 pairs total)
Wiring color code
Optics Adusting Instructions
•Once the fixture's body is mounted into the back box, it is time to adjust the optics angle for the
desired type of light distribution. The fixture's distribution of light can be positioned in two different
position, DEEP (standard optics positioning) and WIDE.
a. To adjust the optics from deep to wide, locate the hex screw in the middle front face of the
fixture. Once located, using a 5 mm hex Allen key (not included), turn the screw counter-
clockwise until both optics stop in the WIDE position. When turning the screw, both optics
move in sync with a range of motion of 75 degrees each.
b. To adjust the optics from wide to deep, using a 5 mm hex Allen key (not included), turn the
screw clockwise until both optics stop in the WIDE position.
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714)
5mm
Standard position (DEEP)
75°
75°
a1
a2
75° Max
Adjustable
DEEP WIDE
Adjustable
WIDE DEEP 75° Max
b1
b2
75°
75°
a. Installer will locate the face plate and locate the two locking studs located on the back of
the face plate. Once located, installer will guide the studs inside the two holes for the face
plate and make sure that the plate fits flat with the body of the fixture.
b. After the face plate is placed, installer will secure the face plate using a 2.5mm hex Allen
key (not included) to lock the face plate in place. Locate the two holes with the screw on the
face plate and using the Allen key, tightened the screw in clockwise pattern to lock the face
plate on the mounted fixture.
Face Plate Mounting Instructions
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714)
a1
2.5 mm
a2
a3
•Once the fixture body is mounted and the optics have been adjusted, it is time to secure the
fixture's face plate on the fixture for a clean finish for even light distribution.
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714)
Maintenance
This fixture was designed and manufactured for a durable,
long lasting use with minimum care. To ensure the
maximum lifespan of this product, we encourage our
customer to provide a quality visual inspection of the fixture
periodically.
If there are any irregular visible sign of issues (i.e moisture
or dust) regarding the fixture please contact us as we will
assist the situation at hand.
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714)
Support
Any questions, problems, or comments you have please
feel free to contact our Customer Service department
during our business hours Monday-Friday 8am-5pm via:
Email: usaorders@targett.com
Phone: (714) 513-1991
Visit our website: http://www.targetti.us
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Targetti Außenleuchte Handbücher
Targetti
Targetti DART small Bedienungsanleitung
Targetti
Targetti FEBO EVO 1E3189 Bedienungsanleitung
Targetti
Targetti DART small Bedienungsanleitung
Targetti
Targetti ZEDGE BOLLARD Bedienungsanleitung
Targetti
Targetti JUPITER PRO 1E3767 Bedienungsanleitung
Targetti
Targetti ZEDGE 1E3148 Bedienungsanleitung
Targetti
Targetti MRS. BO Bedienungsanleitung
Targetti
Targetti DART Round Small Bedienungsanleitung
Targetti
Targetti ZEDGE PRO 1E3192 Bedienungsanleitung
Beliebte Außenleuchte Handbücher anderer Marken
LIGMAN
LIGMAN BAMBOO 3 Bedienungsanleitung
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung
urban ambiance
urban ambiance UQL1273 Bedienungsanleitung
TotalPond
TotalPond 52238 Bedienungsanleitung
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Bedienungsanleitung