TE Connectivity 825508-5 Bedienungsanleitung

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1of 2

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com LOC B

408-2746

Hand Crimping Tool 825508-5 24 JAN 12 Rev A

1. INTRODUCTION

This tool, shown in Figure 1, is used to crimp:

•PIDG* terminals and butt splices on stranded

copper wire sizes 22-10 AWG

•PLASTI-GRIP* terminals and butt splices on solid

or stranded copper wire sizes 22-10 AWG

2. CUT WIRE

Insert wire in cutter, close handles briskly.

3. GAGE WIRE

Determine wire size by inserting unstripped wire into

the smallest color-coded gage ring that will accept the

wire. See Figure 2. After stripping, use the adjacent

crimp closure to crimp terminal or splice on wire.

4. STRIP WIRE

Partially open handles and insert wire in correct notch

of wire stripping blades. End of wire must butt against

strip length locator (controls strip length). See

Figure 3. Close handles fully and rotate tool part way

around the wire. Pull wire from tool.

Be sure there are no cut or missing conductor

strands.

5. COLOR CODE

Select the correct color-coded terminal or splice for

the wire size being used:

•Red = AWG 22-16 (0.25-1.5 mm²)

•Blue = AWG 16-14 (1.5-2.5 mm²)

•Yellow = AWG 12-10 (4-6 mm²)

6. CRIMP TERMINAL OR SPLICE

(a) Insert color-coded terminal or splice in crimp

closure adjacent to the matching color-coded wire

gage ring.

(b) Position terminal or splice in crimp closure as

shown in Figure 4 or 5.

firmly in die closure.

(d) Insert stripped wire into terminal until end of

conductor is at least flush with or extended slightly

beyond end of terminal wire barrel.

Insert stripped wire into splice until end of conductor

butts against splice wire stop.

Do not use wires with nicked or missing conductor

strands.

(e) Close handles fully, then open handles by

depressing release lever.

(f) To crimp other half of splice, remove it and

reposition uncrimped half in tool as shown in Figure 5.

Follow same procedure used to crimp first half of

splice. If splice cannot be turned, turn tool around.

(g) Refer to Figure 6 for terminal or splice crimp

inspection procedure.

Figure 1

Figure 2

Figure 3

Figure 4

CAUTION

Strip Length Locator Crimp Closures Wire

Cutter

Release Lever WireStripping

Blades Color-Coded

Wire Gage

Rings

GageWireandUseAdjacent Crimp Closure

UseCorrect

Size Notch EndofWireButtsAgainst

Strip Length Locator

PLASTI-GRIP

Terminal

EndofInsulationBarrelis

Flush with Sides of Dies

PIDG

Terminal

“B” = Wire Barrel

“C” = Insulation Barrel

“B”

“C”

ORIGINAL INSTRUCTIONS

408-2746

2of 2

Rev A

7. REVISION SUMMARY

•Removed “AMPLIVERSAL” in title

Figure 5

Figure 6

Butt Splices

“B” “B”

“C”

“C” PIDG PLASTI-GRIP

“B” = Wire Barrel

“C” = Insulation Barrel

Wire Stop Wire Stop

EndofInsulationBarrelis

Flush with Sides of Dies

End of Insulation

Barrel is Flush

with Sides of Dies

Inhaltsverzeichnis

Andere TE Connectivity Crimpwerkzeuge Handbücher

TE Connectivity

TE Connectivity 2063379-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 4-1579001-2 Bedienungsanleitung

TE Connectivity

TE Connectivity 2397100-1 Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 0-1579001-6 Bedienungsanleitung

TE Connectivity

TE Connectivity 2378724-1 Bedienungsanleitung

TE Connectivity

TE Connectivity CERTI- CRIMP Series Bedienungsanleitung

TE Connectivity

TE Connectivity PRO-CRIMPER III 2161732-1 Bedienungsanleitung

TE Connectivity

TE Connectivity CERTI-CRIMP II 2381707-1 Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 539 723-2 Bedienungsanleitung

TE Connectivity

TE Connectivity Faston Series Bedienungsanleitung

TE Connectivity

TE Connectivity 1752786-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2844594-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2381454-1 Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 5-1579001-3 Bedienungsanleitung

TE Connectivity

TE Connectivity HVA280-2P Bedienungsanleitung

TE Connectivity

TE Connectivity Positive Lock A Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity SDE Bedienungsanleitung

TE Connectivity

TE Connectivity SOLISTRAND 1752868-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 58075-1 Bedienungsanleitung

TE Connectivity

TE Connectivity CERTI-CRIMP 90165-1 Bedienungsanleitung

TE Connectivity

TE Connectivity 2377672-1 Bedienungsanleitung

TE Connectivity

TE Connectivity SDE-SA Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 0-1579001-3 Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

molex

molex 63811-5100 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

molex

molex 63825-3000 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung