Technoline WT643 Bedienungsanleitung

WT643 Weather Station

Instruction Manual

The weather station desk clock combines the following functions:

– Time with Projection – Alarm – Calendar – Indoor and Outdoor Temperature

– Indoor and Outdoor Humidit – Weather Forecast

1. “MODE” button

2. “MIN / MAX” button

3. “▲ °C & °F” button

4. “▼” button

5. “SET / ALARM” button

6. “CHANNEL” button

7. BATTERY COMPARTMENT

8. AC/DC ADAPTER JACK

9. TIME PROJECTION FOCUS

10. CRYSTAL WEATHER FORECASTER

11. “SNOOZE / LIGHT” buttonButtons :

Getting started

Due to the heav power consumption of the unit it is strongl recommended to

use the A/C adapter at all times.

1. Install the A/C adapter into the AC/DC ADAPTER JACK (8) hole

2. Install 3 x ‘AAA’ size batteries b sliding open the BATTERY

COMPARTMENT (7). Replace batter compartment door when finished.

See batter warnings below

3. When batteries are in use, the s mbol of the batter will be shown on the

clock face when the batteries are low and need replacing.

4. The batteries in the unit will keep the time and other details working if and

when the A/C adapter is removed.

NOTE: If onl batteries are being used one can illuminate the clock face for a

period of 20 seconds when the “ SNOOZE / LIGHT” button (11) is pressed.

When required, the unit can be reset to default setting b removing batteries

and / or A/C adapter and re-installing them.

The preset language is English (EN) after reset or after installation of batteries

and the date is Thursda (TH), 2009 Januar 1.

To set time:

1. Press and hold “SET / ALARM” button (5) for 2 seconds and the HOUR digits

will flash. Press “▲ °C & °F” button (3) or “▼” button (4) to change

the

HOUR setting.

2. Press “SET / ALARM” button (5) again and the MINUTE digits will flash.

Press “▲ °C & °F” button (3) or “▼” button (4) to change the

MINUTE setting.

3. Press “SET / ALARM” button (5) again to change the date/month month/date

setting. Press “▲ °C & °F” button (3) or “▼” button (4) to change.

4. Press “SET / ALARM” button (5) again and the LANGUAGE digits will flash.

Press “▲ °C & °F” button (3) or “▼” button (4) to change the

LANGUAGE

setting. (*See below for language settings)

5. Press “SET / ALARM” button (5) again and the YEAR digits will flash.

Press “▲ °C & °F” button (3) or “▼” button (4) to change the YEAR

setting.

6. Press “SET / ALARM” button (5) again and the MONTH digits will flash.

Press “▲ °C & °F” button (3) or “▼” button (4) to change the MONTH

setting.

7. Press “SET / ALARM” button (5) again and the DATE digits will flash.

Press “▲ °C & °F” button (3) or “▼” button (4) to change the DATE

setting.

8. Press “SET / ALARM” button (5) again to change between 24-hour clock and

AM/PM. Press “▲ °C & °F” button (3) or “▼” button (4) to change.

“24H”

indicates 24-hour clock. “12H” indicates AM / PM.

9. Press “SET / ALARM” button (5) to confirm.

*Language setting: -The unit is equipped with 7 languages for the screen displa .

Toggle between these languages: EN for English; –GE for German; IT for Italian;

FR for French; NE for Dutch; ES for Spanish; and DA for Danish.

NOTE: The preset language is English (EN) after reset or after installation of

batteries and the date is Thursda (TH), 2009 Januar 1.

To set the alarm:

1. Press “MODE” button (1) once to displa the alarm time. This will be indicated

b an “AL” s mbol.

2. Press and hold “SET / ALARM” button (5) for 2 seconds and the HOUR digits

will flash. Press “▲ °C & °F” button (3) or “▼” button (4) to change

the HOUR

setting.

3. Press “SET / ALARM” button (5) again and the MINUTE digits will flash.

Press “▲ °C & °F” button (3) or “▼” button (4) to change the MINUTE

setting.

4. Toggle b pressing “MODE” button (1) between ‘Actual Time’ and ‘Alarm Time”

To turn alarm on and off:

1. Toggle b pressing “MODE” button (1) between current time and alarm time

until alarm time is displa ed.

2. Press “SET / ALARM” button (5) once to turn on alarm. A s mbol will be

shown. Press “SET / ALARM” button (5) again to turn off alarm.

3. The alarm will sound once the preset alarm time has been reached.

Press “SET / ALARM” button (5) to deactivate the alarm.

4. Press and hold the “SNOOZE / LIGHT” button (11) for approximatel 3

seconds to activate snooze. The alarm will sound again after 5 minutes for 1

minute and 59 seconds.

Interpreting the weather forecast symbols

The weather station requires at least 24 hours on acclimatizing to local weather

conditions. The weather station process and anal ze the weather patterns for the

past 24 hours in order to determine the future weather. Until that time has

elapsed, the predicted weather forecast ma not accuratel reflect the actual

weather for our immediate area.

The weather station will displa the s mbols (see figure 3) to indicate the

predicted weather forecast for the next 12 to 24 hours for an area within a radius

of approximatel 30-50 km.

Note:

1. The weather forecasting is relativel accurate. Accurac rate might be lower in

extreme weather conditions. The weather forecast is onl for reference and it is

onl for domestic use. Do NOT rel on the weather station for weather forecast

for an serious matter replies including but not limited to: personal health, life

and death situation, an business or financial decisions, and/or agricultural

planning.

2. The weather forecast does not displa the current weather. It displa s the

weather for the future.

EMOTE TEMPE ATU E SENSO

This weather station is equipped with outdoor temperature and humidit displa .

The weather station is capable of s nchronizing with up to 3 external sensors.

1 external is included with this weather station. Contact our local authorized

re-sellers to purchase additional external sensors.

RTS 1. Hang hole

RTS 2. Batter compartment screws

RTS 3. “RESET” button

RTS 4. “Channel 1 2 3” switch

Batteries installation

1. Open batter compartment on the back of the unit b removing the two small

screws (RTS 2) with a Philips head screwdriver. (see figure 4)

2. Install / replace with 2x “AAA” size batteries in the compartment. It is

recommended that onl alkaline batteries are used. Do not use rechargeable

batteries.

3. The weather station is capable of receiving up to 3 different channels. Select

the channel number (1, 2, or 3) b sliding the “Channel 1 2 3” switch (RTS 4).

If ou onl have 1 remote temperature sensor, select 1.

4. Press the “reset” button (RTS 3) once and the red light will flash once.

5. Replace the batter compartment on the back of the unit b tightening the

two screws (RTS 2).

Installation

1. Place the remote temperature sensor at a desired place b mounting the

unit’s hang hole (RTS 1) on a screw (screw not included). Alternativel , the

unit can be place on a flat horizontal surface.

2. The unit can be placed indoor or outdoor. The unit is weather proof. Do not

submerge unit in water. Do not expose unit to water for prolonged periods.

Avoid accumulation of water and or snow on unit. Avoid exposing unit to

direct sunlight. Remove unit from the exterior in extreme or harsh weather,

including but not limited to hurricane, t phoon, and c clones seasons. Do not

place the unit in area of high winds.

3. Do not place the remote temperature sensor more than 30 meters (98 feet)

from the receiving weather station. The remote temperature sensor is most

effective if there are no obstruction and interference between the remote

temperature sensor and the weather station. The remote temperature sensor

might have to closer than 30 meters if the weather station is not able to

receive an signals. This is due to obstructions and interference. The user

might need to experiment with various locations to get the best reception.

Configuring Weather Station to receive remote temperature signals.

1. Follow the above instructions to set up remote temperature sensor.

2. Press “CHANNEL” button (6) on weather station for 3 seconds. will flash.

This will reset all temperature memories.

3. The weather station will begin scanning for signals for channel 1. As soon as

signals are received for channel 1, the temperature will be displa ed. The

weather station will automaticall scans for the other channels. It will scan

each channel for approximatel 3 seconds before skipping to the next channel.

4. Once all our channels are received press “CHANNEL” button (6) once to

confirm the channel.

5. The weather station will receive a new signal automaticall ever 30 seconds

to update the remote temperature.

6. Press “CHANNEL” button (6) on weather station repeatedl to toggle between

channel 1, channel 2, and channel 3.

7. will be displa ed if an of the remote temperature sensor’s batter needs

replacing.

Temperature & humidity memory

1. Press “MAX/MIN” button (2) to displa maximum recorded temperature,

minimum recorded temperature, and current temperature. “max” indicates

maximum temperature. “min” indicates minimum temperature.

2. Press “MAX/MIN” button (2) again to displa current temperature and humidit .

Celsius / Fahrenheit

1. Press “▲ °C & °F” button (3) to toggle between displa ing the temperature in

Celsius and Fahrenheit.

Note:

1. The humidit range is 20% to 95%

2. When the alarm is operating the signal from the sensor will not update the

temperature and humidit readings.

Swivel Ceiling Time Projector and SNOOZE Button:

This clock is equipped with night time projection.

B pressing the “SNOOZE / LIGHT” button (11), the current time will be projected

for about 8-12 seconds. The time can be projected onto a flat surface in a ver

dark room. Turn the “TIME PROJECTION FOCUS” knob (8) clockwise or

counterclockwise to adjust focus.

WA NINGS

This main unit is intended to be used only indoors.

Do not subject the unit to excessive force or shock.

Do not expose the unit to extreme temperatures or humidity.

Avoid exposing the unit to direct sun light.

Do not immerse in water.

Do not remove any screws unless specified.

Do not dispose this unit in a fire as it may explode.

Dispose the unit legally and recycle if possible.

Batteries safety warnings:

1. Please read all instructions carefully before use.

2. Install batteries correctly by matching the polarities (+/-).

3. Always replace a complete set of batteries.

4. Never mix used and new batteries.

5. emove exhausted batteries immediately.

6. emove batteries when not in use.

7. Do not recharge and do not dispose of batteries in fire as the batteries may

explode.

8. Ensure batteries are stored away from metal objects as contact may cause a

short circuit.

9. Avoid exposing batteries to temperature or humidity extremes or direct sunlight.

10. Keep all batteries out of reach from children. They are a choking hazard.

11. Please retain packaging for future reference.

Specifications

1. Temperature ange : -10℃

℃℃

℃ to50℃

℃℃

℃ ( 14°F to 122°F)

2. Temperature Tolerance : +/- 2℃

℃℃

℃

3. Calendar range: year 2000 to year 2099

Consideration of dut according to the batter low

Old batteries don’t belong to domestic waste because the could cause damages of

health and environment. End-user are committed b law to bring back needed

batteries to distributor and other collecting points.

Inhaltsverzeichnis

Andere Technoline Wetterstation Handbücher

Technoline

Technoline WS9135 Bedienungsanleitung

Technoline

Technoline WS 6760 Bedienungsanleitung

Technoline

Technoline WS 9123 Bedienungsanleitung

Technoline

Technoline WS 9422 Bedienungsanleitung

Technoline

Technoline WS6462 Bedienungsanleitung

Technoline

Technoline WS 6830 Bedienungsanleitung

Technoline

Technoline WS 9069 Bedienungsanleitung

Technoline

Technoline WS6767 Bedienungsanleitung

Technoline

Technoline WS 9117 Bedienungsanleitung

Technoline

Technoline WS 6820 Bedienungsanleitung

Technoline

Technoline WS 6445 Bedienungsanleitung

Technoline

Technoline WS550 Bedienungsanleitung

Technoline

Technoline WS6447 Bedienungsanleitung

Technoline

Technoline WS 2307 Bedienungsanleitung

Technoline

Technoline WT 171 Bedienungsanleitung

Technoline

Technoline WS9612 Bedienungsanleitung

Technoline

Technoline WS9123 Bedienungsanleitung

Technoline

Technoline WS 6720 Bedienungsanleitung

Technoline

Technoline WS 9910 Bedienungsanleitung

Technoline

Technoline WS 9274 Bedienungsanleitung

Technoline

Technoline WS 6750 Bedienungsanleitung

Technoline

Technoline WS1900 Bedienungsanleitung

Technoline

Technoline WS 585 Bedienungsanleitung

Technoline

Technoline WS 6600 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Renkforce

Renkforce 1208067 Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung