Techone 1300 Popwing Bedienungsanleitung

1. These EPP flying wings are very popular for

outdoor flying.

2. Made of high quality EPP material, it is very

durable and easy to fly.

3. Most of the parts are pre-assembled in our

factory, for you it’s very easy to build.

Fuselage length: 390MM (15.3in.)

Wingspan: 1300MM (51.1in.)

Flying Weight:484g (with battery)

Motor: AS2216 KV 1250

ESC: 30 Amp

Propeller: 9*5 or 9047 sf

Servo: 10-17g micro servo*4pcs

Radio: 4/more channel

Battery: 11.1V1800mAh Li-po 25C

Wind strong enough to make the trees rustle

A street with many trees or street lamps

Close to high voltage electrical wires

High Population density areas

Cautions for flying

Large gyms, front lawns and parks make

excellent flying areas. Make sure you

have permission to fly and follow safety

guidelines set by local authorities.

The calmer the wind, the better!

Note for Storage

Please disconnect the lipo packs when

finished flying

Do not press or crush the airplane when

storing

The best way to store is to hang the airplane

to keep the control surface rigid

Recommended Flying Setup

Max servo travel of aileron: 40degrees up

and 40degrees down(28mm)

Max servo travel of elevator:50 degrees up

and 50 degrees down(28mm)

235-245mm away from the nose

235-245mm

1.Wing

2.Wing fences

3.Skid

4.Motor mount

5.Reinforcement for wing connecting

square tube

6.Battery fixing board

7.Wing reinforcing carbon fiber rod

8.Nylon strap

9.Push rod with Z bend

10.Wing connecting square tube

11.Glass fiber control horn

12.Adjustor

13.Motor fixing screws

Assembly steps

Fix the left and right wing with glue.

Insert the wing connecting square tube into

the pre-reserved slot and fix with glue.

Reinforcement for wing connecting square tube

1pc

2pcs

1pc

2pcs

1pc

2pcs

1pc

2pcs

4pcs

Motor mount

Install the motor mount on corresponding

place in above picture with glue. Please align

the round holes at the central line of the airframe.

Battery fixing board

Put the battery fixing board on the bottom of

wing, then fix with glue.

Find 4 burned holes on top and bottom wing

(2 holes each).

Cut a slot along the 2 burned holes on top of

wing.

Cut another slot along the 2 burned holes on

bottom of wing.

Prepare 2pcs carbon rods.(

carbon fiber rod)Wing reinforcing

Insert the carbon rods into slots on both sides

of wing, then fix with glue.

Put the skid on the central line which is near the

nose and fix with glue.

The pointed position in black is the adhesive

position of wing fence and the lower arc line of

the wing. (The burned holes can be seen clearly

on the wing fences)

Align the two burned holes with lower arc line

of wing as picture shown, then fix with glue.

Tighten the screw after finishing the

installation of the servo and servo arm.

The completion of the servo arm installation

Place servo into the pre-reserved servo house

and fix with glue.

Cut a slot for embeding the servo wire.

Embed the servo wire into the slot.

Glass fiber control horn and adjustor

Use the reamer to enlarge the aperture to fit

the adjustor.

Fix the adjustor and control horn with glue as

picture shown.

Cut a slot for installing the glass fiber control

horn as picture shown.

Put the control horn into the slot and fix with

glue.

Connect the servo and control horn with

Z bend push rod.

Cut off the redundant wire with pliers.

Tighten the screw of adjustor after make

sure the control surface and wing is in the

same level.

The completion picture after installation of the

servo and push rod.

Motor fixing screws

Install motor on motor mount with screws.

Propeller.

Install the propeller on motor shaft.

Then put the washer on propeller as picture

shown.

Screw down the bullet head.

The planform of the installed motor and propeller.

Make sure the motor and propeller is in neutral.

ESC 30A

Connect motor and ESC wire.

Nylon strap

Thread nylon straps through the equipment

cabin.

Put ESC inside the equipment cabin as picture

shown.

Receiver

Plug the equipment connectors into

corresponding receiver holes.

Tighten the nylon straps after placed all

equipments neatly.

Cut off redundant part with pliers.

Battery 11.1V 1800MAH 3S

Put the battery into battery house.

Fix battery with velcro strap.

The completion of the airplane.

A perfect 1300 Popwing-EPP is done after your

careful assembly. While assembly, the flying

weight is really critical to the flight performance

and will be affected by adding weight, so you

should reduce any unnecessary weight while

assembly. Then you’ll get the best flying

performance.

Andere Techone Spielzeug Handbücher

Techone

Techone angel epp Bedienungsanleitung

Techone

Techone Arrow 3d Bedienungsanleitung

Techone

Techone P51 3D-EPP Bedienungsanleitung

Techone

Techone MANTH Bedienungsanleitung

Techone

Techone Yak54-F3P Bedienungsanleitung

Techone

Techone Gent EPP Bedienungsanleitung

Techone

Techone Mini Popwing Bedienungsanleitung

Techone

Techone rainbow-epp Bedienungsanleitung

Techone

Techone Extra 300 EPS Bedienungsanleitung

Techone

Techone Yak55 3D EPP Bedienungsanleitung

Techone

Techone EPP-P51D Bedienungsanleitung

Techone

Techone Park-1100 EPP Bedienungsanleitung

Techone

Techone Mini Tempo 3D-EPP Bedienungsanleitung

Techone

Techone Malibu III Bedienungsanleitung

Techone

Techone Sukhoi EPP Bedienungsanleitung

Techone

Techone MXS-HCF Bedienungsanleitung

Techone

Techone SU-27 Bedienungsanleitung

Techone

Techone AEROLUS F3P Bedienungsanleitung

Techone

Techone leader 3D EPP Bedienungsanleitung

Techone

Techone Malibu-F3P Bedienungsanleitung

Techone

Techone SWIFT 3D-EPP Bedienungsanleitung

Techone

Techone BLUEFOX 2012 3D-HCF Bedienungsanleitung

Techone

Techone 02A-703 Metis Bedienungsanleitung

Techone

Techone Yak54 F3P Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung