TeeJet 814-FM Bedienungsanleitung

814-FM

Monitor

Programming and Operating Manual

(2.00)

98-70014-R0

MI814-FM Programming and Operating Manual, 03/2000 1 of 17

Table Of Contents

TABLE OF CONTENTS ........................................................................................................................................................................ 2

INSTALLATION..................................................................................................................................................................................... 3

PUMP CUT-OFF INSTRUCTIONS ...............................................................................................................................................................4

POWERING CONSOLE ON/OFF ........................................................................................................................................................ 5

POWER ON.............................................................................................................................................................................................5

POWER OFF............................................................................................................................................................................................5

OVERVIEW OF MONITOR DISPLAYS............................................................................................................................................. 6

DISPLAYS................................................................................................................................................................................................ 7

JOB VOLUME.......................................................................................................................................................................................... 7

JOB FLOW RATE.....................................................................................................................................................................................7

PRESSURE /FLOW RATE......................................................................................................................................................................... 8

TOTAL VOLUME.....................................................................................................................................................................................8

AUTOMATIC FILLING .............................................................................................................................................................................9

PROGRAMMING GUIDELINES ....................................................................................................................................................... 10

IMPORTANT PRELIMINARY INFORMATION ...........................................................................................................................................10

PROGRAMMING THE 814-FM SPRAYER CONTROL SYSTEM ............................................................................................... 11

UNITS...................................................................................................................................................................................................11

FLOW METER PULSES ..........................................................................................................................................................................11

Manual Entry..................................................................................................................................................................................11

Automatic Calibration....................................................................................................................................................................12

PRESSURE TRANSDUCER LOW PRESSURE CALIBRATION......................................................................................................................13

PRESSURE TRANSDUCER MAXIMUM RATING (P HI) ............................................................................................................................. 14

FILL VALVE .........................................................................................................................................................................................14

DATE/TIME ..........................................................................................................................................................................................15

PRINTING ............................................................................................................................................................................................. 16

JOB REPORT .........................................................................................................................................................................................16

TOTAL REPORT ....................................................................................................................................................................................16

HIDDEN TOTAL VOLUME COUNTER........................................................................................................................................... 17

OEM REPORT ......................................................................................................................................................................................17

MI814-FM Programming and Operating Manual, 03/2000 2 of 17

Installation

☛The TeeJet 814-FM monitor is powered by +12VDC. The fused power lead (brown wire) should

go to the positive terminal of the battery. The blue or white wire to the negative or ground

terminal of the battery.

☛The flow meter should be plumbed so that all liquid passing through it is intended to be

measured.

☛The flow meter cable lead should be extended and connected to the the flow meter.

☛The pressure sensor (if used) can be installed at any point in the plumbing system. It should be

mounted in a verticle position on a short stand pipe to help prevent damage from freezing

temperatures.

☛The pressure sensor lead should be extended and connected to the pressure transducer, if

used. If no pressure transducer is used, this cable lead can be tied back for possible future use.

☛The valve lead should be extended and connected to the optional auto fill valve. If an auto fill

valve is not used, this cable can be tied back for possible future use.

☛The auto fill valve used with this system must be a negatively switched valve. This system can

also be used to disengage a pump if desired. Refer to the Pump Cut-off instructions in the

following section.

☛If an optional printer will be used with the system, it requires a separate cable connection to the

console. The printer has two connections, one is the data connection and the other is power for

the printer.

MI814-FM Programming and Operating Manual, 03/2000 3 of 17

PUMP CUT-OFF INSTRUCTIONS

While the 814-FM is capable of switching an auto fill valve, it can also switch an electric transfer

pump. The 814-FM is limited to switching 1.8 amps directly. If the pump requires a higher current to

activate, a relay must be used to isolate/protect the 814-FM. When using a relay for switching higher

currents, it is important that the power supply for the relay and load come through a correctly sized

fuse and directly from the pump power source, not the 814-FM. Keep in mind that the 814-FM is

negatively switched and the relay will need to be wired accordingly.

MI814-FM Programming and Operating Manual, 03/2000 4 of 17

Powering Console On/Off

POWER ON

After all the necessary electrical

connections have been made

the console is ready to be

powered on. To power the 814-

FM on press the P

RO key once.

Initially the console will display

the software version of the

console in the display for

approximately 2 seconds. This

information will be needed

when calling for support. After

2 seconds the display will show

the normal operating view.

814-FM

MONITOR

P814-FM V 2.00A

CLR

JOB

OFF

POWER OFF

814-FM

To manually power the console

off, press the and CLR keys

simultaneously. The console

will then save any new

information (volume counters)

to memory and will power off.

MONITOR

CLR

Note: The console also has

an Auto Power Down feature.

The console will power itself

off after 10 minutes if not

receiving any inputs.

JOB

OFF

MI814-FM Programming and Operating Manual, 03/2000 5 of 17

Overview of Monitor Displays

•and keys are used for scrolling through the list of display information or for changing values

when a value is flashing.

•Holding the

CLR key for 3 seconds is used to clear a job volume memory (only one job or all job

memories when the total counter is displayed).

•A short press on the P

RO key allows you to enter amount to be filled if the Fill Valve option has been

activated. You can only enter this step when the job number is visible.

•The fill valve is always switched ON when the switch is in the ON position.

•The fill valve will be automatically controlled when the switch is in the AUTO position.

•The Job selection switch is used to scroll through the possible job settings. You can only change

jobs when the job number is visible.

•The print button is used to print the volume of the selected job or to print the list of all non zero

jobs and the total value.

•GAL (L) or GPM (LPM) is flashing on the screen when automatic filling is busy. Automatic filling

can be stopped by pressing shortly on the CLR key.

Very Important: Whenever you are working around a sprayer or chemicals, be sure to wear

protective clothing and eyewear.

MI814-FM Programming and Operating Manual, 03/2000 6 of 17

Display

Backlit LCD display for

24 hour operations.

Sensor Monitors

LED’s light when

sensor is sending

signals to console

ON/OFF/AUTO Switch

Used to activate the fill valve/pump.

Auto selection controls shut-of

automatically

Main Connection

Connection for main

cable with leads to

power, sensors and

vales if used.

Data Connection

Used for connection

of optional printer.

Power

Press 1 time to power the

console on.

Easily Accessible Program Mode

Press for 3 seconds to enter/exit program

mode.

Print Button

Used with optional printer

to print individual job

reports or a total report of

all jobs.

Display Selection

Use these keys to chose which

display to view. Chose Job

Volume, Job Flow Rate,

Pressure/Flow Rate or Total

Volume

Clear Function

Used to clear individual job

memories or the total volume

memory. Press and hold to

clear

Job Selection Switch

Use to change the display

from one job to the next.

Displays

JOB VOLUME

814-FMIn this display the console will show the

total accumulated volume for the job

number selected.

MONITOR

To change to a new job selection use

the job selection switch. Pushing up on

the job switch will increase the job

number, down will decrease the job

number.

JOB 3 150.0 GAL

CLR

JOB

This volume will be counted any time

that the master boom switch is in the

ON or AUTO position and flow is going

through the flow meter.

OFF

Maximum amount 6500 Gallons

(6500 Liters)

To clear this value, press and hold the CLR key for 3 seconds.

Press the key to advance to the next display.

JOB FLOW RATE

814-FM

In this display the console will show the

current flow rate in GPM (LPM) that is

going through the flow meter.

MONITOR

The flow rate will be displayed any time

flow is going through the flow meter

regardless of the position of the master

boom switch. In this example, the total

volume is still being accumulated in Job

JOB 3 75.0 GPM

CLR

JOB

Press the key to advance to the next

display. PRINT

OFF

MI814-FM Programming and Operating Manual, 03/2000 7 of 17

PRESSURE /FLOW RATE

This display shows the current pressure

and flow rate in GPM (LPM). 814-FM

MONITOR

The flow rate and pressure will be

displayed any time flow is going through

the flow meter and pressure is acting on

the pressure transducer, regardless of the

position of the master boom switch.

P45 PSI 75.0 GPM

CLR

Note: This display is only available

when a pressure transducer has been

installed, connected and properly

programmed into the console. JOB

OFF

Press the key to advance to the next

display.

TOTAL VOLUME

814-FM

This display shows the total

accumulated volume for all jobs.

MONITOR

This volume will be counted any time

that the master boom switch is in the ON

or AUTO position and flow is going

through the flow meter.

TOTAL:2500.0 GAL

CLR

To clear this value, press and hold the CLR

key for 3 seconds. JOB

Note: Clearing this value also clears

all individual job totals. Insure all

individual job information has been

OFF

printed and/or recorded before clearing

the Total Volume.

MI814-FM Programming and Operating Manual, 03/2000 8 of 17

AUTOMATIC FILLING

Automatic filling is used to deliver a predefined volume of liquid by opening a filling valve (switching

on a pump) until the desired volume has been measured. The electric fill valve is driven by the

console.

To use the automatic filling feature the console must first be programmed for this function. Refer to

the “Fill Valve” step in the programming section of this manual. This step should be set to “YES”.

To begin auto filling, first select the job

number you would like to use with the

Job Selection switch. Next press the P

key once to access the amount to be

filled. Use the and/or keys to

adjust the volume to be filled. After the

volume has been set, press the P

RO again.

This will advance back to the job

selection display. The GAL (L) or GPM

(LPM) text will be flashing to indicate that

the console is waiting for further action.

Next move the master switch to the

AUTO position. This will activate the fill

valve (transfer pump) to begin the filling

process.

814-FM

MONITOR

PFILL: 0.0 GAL

CLR

JOB

OFF

During the filling process you can temporarily close the filling valve by turning the master switch back

to the OFF position. The filling is continued after switching back to the AUTO position. When the

desired volume is reached the console will automatically close the filling valve (disengage the pump).

If you want to stop the automatic filling you can press the CLR key and the GAL (L) or GPM (LPM) text

will stop flashing and the fill valve will be closed.

The filling valve can be driven manually by switching the master switch to the ON or OFF positions.

MI814-FM Programming and Operating Manual, 03/2000 9 of 17

Programming Guidelines

Make sure that all hardware components are properly installed and tested. Before you start the

programming process you should first be sure that the console and all sensors are working properly.

IMPORTANT PRELIMINARY INFORMATION

Before you begin, it is recommended that you review the following Programming Guidelines that

control the programming process:

☛To enter the program mode press and hold the P

RO key for 3 seconds. The master switch must be

in the off position.

☛To exit the program mode press and hold the P

RO key for 3 seconds, your inputs will be stored and

the computer will exit the program mode. This action can be done at any time but will not be

necessary until the last programming step has been completed.

☛To increase the value of a programmable digit, press the key. To decrease the value, press the

key. These keys are located directly to the right of the display. For some programming steps,

pressing and holding the or key will change the programmable value rapidly. Pressing the

or key once will change the value by one increment.

☛Pressing the and keys simultaneously in some programming steps will will start an

automatic calibration.

☛A short press of the CLR key in program mode will reset the value to its default value.

☛Holding the CLR key for 2 seconds will clear the value to zero.

☛Pressing the P

RO key will advance you to the next programming step. After the last programming

step, the console will return to the first programming step.

☛Note: Due to differences in fonts, some letters on the displays shown in this manual are

not identical with the corresponding letters on the display of the controller. We tried to

match them as close as possible.

MI814-FM Programming and Operating Manual, 03/2000 10 of 17

Inhaltsverzeichnis

Andere TeeJet Landwirtschaftliche Geräte Handbücher

TeeJet

TeeJet MATRIX 908 Bedienungsanleitung

TeeJet

TeeJet 844-RA Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung