Tekcomm TCT 1500 Bedienungsanleitung
SAT 4000
kanäle
Update via
USB OTA 1.00W
stand-by
Digital
audio
User Manual
Digital Satellite
Receiver TCT 1500
1.1 Safety Instructions 2
1.2 Storage 2
1.3 Equipment Set-up 2
1.4 Accessories 2
1.5 Usage of external USB devices 3
2.1 Front Panel 3
2.2 Rear Panel 3
2.3 Remote Control Unit 3
2.4 Default PIN code: 0000 4
2.5 Installing the Batteries 4
2.6 Using the Remote Control 4
3.1 Basic connection with SCART cable 4
3.2 Connecting to Satellite Dish 4
3.3 Connecting to a Digital Audio Amplier 4
3.4 Connecting to USB device 4
4.1 OSD Settings 4
4.2 My Dish 5
5.1 TV 6
5.2 Radio 7
5.3 Accessory 7
5.4 Conguration 7
Subject to alterations. In consequence of continuous research and development technical
specications, design and appearance of products may change. All product names are
trademarks or registered trademarks of their respective owners.
© TekComm 2011. All rights reserved. 07/2011
In a closed or poorly ventilated cabinet; directly on
top of or under any other equipment; on a surface
which might obstruct the ventilation slots.
To direct sunlight or near any other equipment
that generates heat; to rain or intense moisture;
to intense vibration and to any shock which may
cause permanent damage to your receiver or to
any magnetic objects, such as loudspeakers,
transformers, etc.
Do not use a damaged power cord. It may cause a
re or an electrical shock. Do not touch a power cord
with wet hands. It may cause an electric shock.
When the receiver is not used for a long period of
time, you should unplug the power cord from the
wall socket.
Do not use alcohol or ammonia based liquids to
clean the receiver. If you wish, you may clean your
receiver with a soft lint-free cloth slightly made damp
with a mild soap solution, only after disconnecting
from the mains voltage supply. Make sure no foreign
objects fall through the ventilation slots because this
could cause re or an electric shock.
Do not place any objects on top of the receiver
because this might prevent proper cooling of the
components inside.
Never open the receiver cover. It is dangerous to
touch the inside of the receiver due to high voltage
currents and possible electrical hazards and your
warranty will be void. Refer all maintenance or
servicing to suitably qualied personnel.
When you are connecting cables, be sure that the
receiver is disconnected from the mains supply
voltage. Wait a few seconds after switching off the
receiver before you move the receiver or disconnect
any equipment.
It is a necessity that you only use an approved
extension and compatible wiring that is suitable for
the electrical power consumption of the installed
equipment. Please ensure that the electrical power
supply corresponds with the voltage on the electrical
identication plate at the back of the receiver.
If the receiver does not operate normally even after
strictly following the instructions in this user manual,
it is recommended to consult your dealer.
Your receiver and its accessories are stored and
delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it,
make sure that all the parts are included and keep
the packaging away from children. For transporting
the receiver from one place to another or if you are
returning it under warranty conditions, make sure to
repack the receiver in its original packaging with its
accessories. Failing to comply with such packaging
procedures could void your warranty.
We recommend you consult a professional installer to
set up your equipment. Otherwise, please follow the
instructions below:
Refer to the user manual of your TV and
your antenna.
Make sure that the SCART cable and outdoor
components are in a good condition and the SCART
connection is well shielded
This manual provides complete instructions for
installing and using this receiver. The following
symbols will serve as follow.
Indicates warning information.
Indicates any other additional
important or helpful information.
Represents a button on the
remote control or the receiver
Move to Represents a menu item within
a window. (Italic Character)
1. TCT 1500 1x
2. User’s Manual 1x
3. Remote control unit 1x
4. Batteries (AAA type) 2 x
The batteries should not be recharged,
disassembled, electrically short-
circuited, be mixed or used with other
types of batteries.
If rechargeable accumulators instead
of batteries are going to be used, we
recommend using (e.g. NiMH) types
with low self-discharge to ensure long
time operation of remote control.
It is recommended to use USB 2.0 storage devices.
TekComm cannot guarantee compatibility to all types
of USB storage devices.
It is advised not to store important information
on USB storage devices used with the receiver.
Always make backups of data on USB storage
device before usage with receiver. TekComm will
not take responsibility for any loss of information or
circumstances caused by loss of information.
1. INDICATION LED: Green LED during
operation, red LED in standby mode.
2. REMOTE SENSOR: Reception of
remote control signals.
3. USB CONNECTION: Connection to USB
storage device. Fig. 1
Fig. 2
1. A Loop through to connect an
extra receiver to the satellite
signal from dish
2. To connect to the LNB for
satellite signal from dish
3. To connect to your TV set
using a SCART cable.
4. To connect to the input of your
digital audio amplier.
5. Your receiver requires a mains
voltage of 100~240 V AC
(Auto-selectable), 50/60Hz
±5%. Make sure to check the
power specication before
connecting your receiver to
the wall outlet.
Fig. 3
1. q Turns the receiver On/Stand-
by
2. ! Mutes audio output of the
receiver
3. Changes channel and controls
numeric functions
4. Opens the available favourite
list if previously congured
5. Toggles between the two the
last watched channels
6. Opens the audio language(s)
and mode selection.
7. Opens the subtitle language(s)
selection
8. Shows the information banner
9. Displays the main menu and
returns to the previous level of
menu
10. Opens the EPG (Electronic
Programme Guide) in
TV mode.
11. Exits from any menu and
sub-menu or cancels the
progressing function
12. pq Switches to the previous/
next programme in TV mode.
Moves the cursor upwards/
downwards in menu mode
13. In TV mode it displays the
channel list according to the
chosen mode.
In menu mode activates the
highlighted menu item.
14. tu Increases/decreases the
volume level in TV mode.
Changes settings for specic
menu items in menu mode
15. Opens the Teletext
language(s) selection
16. Freezes your live audio and
video, press again to cancel
17.
For Teletext and further menu
functions
18. In viewing mode toggles
between TV and radio mode
Fig. 5
Remove the battery cover from the remote
control and put 2xAAA size batteries inside
the compartment.
The diagram inside the battery compartment shows
the correct way to install the batteries.
1. Open the cover
2. Install batteries
3. Close the cover
Fig. 4
To use the remote control, point it towards the front
of the digital receiver. The remote control has a range
of up to 7 metres from the receiver at an angle of up
to 60 degrees.
The remote control will not operate if its path
is blocked.
Sunlight or very bright light will
decrease the sensitivity of the
remote control.
Fig. 6
Connecting a xed satellite dish to your receiver
Fig. 7
Connecting multiple xed dishes to your receiver
using a DiSEqC 1.0 switch Fig. 8
Connect your Digital Audio Amplier with the S/PDIF
connector on the back of the receiver Fig.7
Fig. 9
Ensure your satellite signal is of good quality. It
is recommended that you perform the rst time
installation by following the Installation as described
step by step. It will help you to easily achieve system
conguration and installation setup.
Press pq and tu to change settings for OSD
Language, Audio Language, Subtitle Language,
AUTO Standby, Auto Time Zone and Time Zone.
Use this option to change the language of the OSD.
Use tu to select OSD language to German, French
or English.
Use this option to change the language of the Audio.
Use tu to select Audio language to German, French
or English.
Use this option to change the language of Subtitles.
Use tu to select Subtitle language to German,
French, English or OFF.
This option allows you to enable Auto Standby or to
disable Auto Standby. Auto Standby will switch the
receiver to standby automatically when it doesn’t
receive commands from the remote control for a
period of 3 hours. To avoid the automatic switch off,
use tu to set Auto Standby to OFF.
This option allows you to enable Auto Time Zone or
to disable Auto Time Zone.
If switched ON, it will follow the time zone
automatically where you are.
Use tu to set Auto Time Zone to OFF/ON.
Use this option to set the time zone manual. (Only
possible if Auto Time Zone is OFF.)
You can make a selection from -12:00 till +12:00.
(Steps of 30 minutes).
Press pq and tu to change settings for Switch
Type, Toneburst and DiSEqC.
Use tu to select the the Switch Type of your dish.
You can select DiSEqC 1.0/1.1, DiSEqC 1.2/USALS
or NONE.
For DiSEqC 1.0/1.1, you can select the satellite you
want to use for LNB 1, 2, 3 and 4. Press pq for the
LNB you want to use and press to edit. (Press
the red button to add a satellite from the list.)
Default: LNB1 is set to Astra 19,2E.
You can press on, for example, LNB1 Astra 19,2E
to see the signal level for Strength and Quality.
Now you can turn your dish to get the highest
Strength and Quality level.
If you have aligned your dish to maximum signal,
press .
Use the colour buttons mentioned on the
bottom screen.
= Scan All, = Delete, = Delete
All, = Scan.
After a scan, the list starts with a pre-installed list,
followed with new found channels.
If your pre-installed list, Astra 19,2E,
is NOT giving any signal, you are
probably on the wrong satellite. (Press
button x in viewing mode and
try to get a high as possible signal for
Strength and Quality.)
DiSEqC 1.2/USALS need to be selected if your dish
is mounted on DiSEqC 1.2 motor.
a) First you need to set the LNB type you are using
(YELOW button).
b) Then you have to select your Location (
button).
c) To set your Limit positions, the button will
bring you in a new Set Limit menu.
Move continue or in steps to your end position
East end West.
Select the button to Set West Limit position
you have reached.
Select the button to Set East Limit
position you have reached.
d) Satellite positions
Press pq to select the Position you like to use
and press .
Press the button to Add you like to install.
Select a transponder receivable at your location
(choose Transponder eld and select the transponder
with tu.) Then choose GOTO X” and press . The
dish will turn fast, close to the right position. Use
the Move Step eld for Fine Tuning and adjust the
position of the dish with the tu buttons. Once the
dish is adjusted to the desired position, select the
eld and press to save.
Press the button to scan the position you have
set. (For Astra 19,2E after a scan, the list starts with a
pre-installed list, followed with new found channels.)
You can save 32 satellite positions.
If your pre-installed list, Astra 19,2E
is NOT giving any signal, you are
probably on the wrong satellite. (Press
button x in viewing mode and
try to get a high as possible signal for
Strength and Quality).
If you have no DiSEqC 1.0/1.1 or DiSEqC 1.2/USALS
you can select NONE.
Press pq to select Toneburst and use tu buttons
to switch it OFF/ON.
For Toneburst OFF, you can edit 1 dish.
For Toneburst ON, you can edit 2 dishes.
Press pq to select Receiver and press .
Here you can edit the dish settings. (Press the
button to Add you like to install.)
Select a transponder receivable at your location
(choose the Transponder eld and select the
transponder with tu).
Now you can turn your dish to get the highest
Strength and Quality level.
If you have aligned your dish to maximum signal,
press to save.
Press the button to scan the position you have
set. (For Astra 19,2E after a scan, the list starts with a
pre-installed list, followed with new found channels.)
If your pre-installed list, Astra 19,2E,
is NOT giving any signal, you are
probably on the wrong satellite. (Press
button x in viewing mode and
try to get a high as possible signal for
Strength and Quality.)
All important settings and features of your receiver
can be operated in Main Menu. It consists of the sub-
menus: TV, Radio, Accessory and Conguration.
To open the Main Menu press .
Press tu to move to Main Menu. In Main Menu
press tu to move to TV and press to enter the
TV menu.
Use tu to reach the following sub-menus Fav, Lock,
Edit, Move, Sort, Skip, Delete and Search.
With the button you can change the available
group you would like to use. (All Satellite, Satellite1,
Satellite2, Fav1, Fav2 etc.)
Press tu to select v if you wish to make favourite
lists. Press pq to select the desired channel
and press to add the selected channel to
that favourite group you like to save. Repeat this
operation to remove the channel from the favourite
list. (Press button to save.)
Press tu to select . Then press pq to select the
desired channel and press to lock this channel.
(Press button to save.)
This only works if Channel Lock is
switched ON in the Pin Code menu
from the Conguration menu!
Press tu to select , then press pq to select the
desired channel and to edit this channel. (Press
button to save.)
Press tu to select , then press pq to select the
desired channel and to move this channel. Use
pq to move the channel to its new location and
press to conrm. Repeat this for every channel
you want to move. (Press button to save all
your changes.)
Press tu to select . You can sort channels by
Name A~Z, Name Z~A with the button or Pay-
Free or Free- Pay with the button. Press
or to return the menu. The list is now
sorted by the specied order.
Please take care once desired order is
executed this order stays.
Press tu to select , then press pq to select the
desired channel and to skip this channel. During
zapping in viewing mode, it will pass the skipped
channel. (Press button to save.)
Press tu to select , then press pq to select the
desired channel and to delete this channel. Press
the button to save and conrm or exit the
pop up screen. With the button you can
select the whole list to delete.
Press tu to select , then press and use the
On Screen Display menu to search for a programme.
The EPG shows the programme schedule for all
services broadcasting EPG information.
Not all broadcasters provide
programme information.
Press pq to select the desired channel and the right
screen will show you the available EPG. Press u to
step in to the EPG schedule for the current channel
and use pq for EPG± and tu to change Date.
Use for more details on the selected EPG. Press
to leave.
Book the selected programme in EPG screen with
the button.
A Timer Settings menu will pop up and you can edit
this menu with pq tu and the numeric buttons to
set the timer details. Press to save.
The receiver will switch on to the right programme at
the right time.
Press to move to Main Menu, then press tu
to move to Radio and press to enter the Radio
Channels menu.
Press pq or to move to Radio Channels. Use
tu to move to the following sub-menus Fav, Lock,
Edit, Move, Sort, Skip, Delete and Search. Press
to leave.
For each function, refer to chapters
5.1.1.1 to 5.1.1.8 as the functions
are identical.
The functions in the Radio EPG are
identical to the TV EPG, please read the
chapters 5.1.2 for your reference.
In Main Menu press tu to move to Accessory and
press to enter the menu.
Press pq to select the following sub-menus
Gomoku, Calendar and Calculator.
Press pq to select Gomoku and press . Play the
game Gomoku on your receiver. Use the on screen
help tips to set and play the game.
Press pq to select Calendar and press .
Use the on screen help tips to search in
your Calendar.
Press pq to select Calculator and press .
Use the on screen help tips to use your Calculator.
In Main Menu press tu to move to Conguration
and press to enter the menu.
Use pq to move to the following sub-menus
Installation, TV Setup, PIN Code, Set Timer, Set
Default and SW Update.
Press pq to select Installation and press .
This menu includes the following submenus: OSD
settings, switch type and TP Manager.
For each function, refer to chapters 4.1,
as the functions are identical.
For each function, refer to chapters
4.2.1, as the functions are identical.
Press pq to select a transponder you would like to
Delete or to Scan.
To make a new transponder in your list, you can
use Add.
Inhaltsverzeichnis
