Tektronix RSA5100B series Bedienungsanleitung
RSA5BUP (Options 56 and 59)
RSA5100B Series Real-Time Signal Analyzers
Internal HD and Removable SSD
ZZZ
Instructions
xx
www.tektronix.com
*P075105600*
075-1056-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.
Service safety summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary located in the RSA5100B
Real-Time Signal Analyzer Service manual (Tektronix part number 077-0903-XX)
before performing any service procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
RSA5100B Series Hard Drive Upgrades 1
Kit description
Kit description
This kit describes the installation of the following upgrade options:
Option 56: Removable Solid State Drive
Option 59: Internal Hard Drive
Products
RSA5103B Series. All serial numbers.
RSA5106B Series. All serial numbers.
RSA5115B Series. All serial numbers.
RSA5126B Series. All serial numbers.
Option 56 kit parts list
Quantity Part number Description
1 ea 075-1056-XX MANUAL, TECH: RSA5KB Option 56 and 59
INSTALLATION INSTRUCTIONS
1 ea 071-2191-XX MANUAL, TECH; SVCPT-UPG; TEKTRONIX
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
2 ea 211-1050-XX SCREW, MACHINE; 6-32 X 0.312 L, PNH, STEEL,
ZINC FINISH, T15
4 ea 211-1081-XX SCREW, MACHINE; M3 X 0.5 X 3.5MM,
FLAT WAFER HD W/SERRATIONS STRESS
RELIEVED, PHL, ZINC PLATED STEEL
1 ea 407-5337-XX BRACKET, RHDD; SATA COMBO CABLE
RETENTION
1 ea 407-5473-XX BRACKET; HARD DRIVE 2.5 INCH REMOVABLE
1 ea 335-3314-XX MARKER, ID, REMOVABLE HD
1 ea 850-0263-XX DRIVE ASSEMBLY; REMOVABLE HARD DRIVE,
PROGRAMMED, RSA5XXXB SERIES
1ea N/A LABEL, MANUFACTURED; PRODUCT LABEL,
SAFETY CONTROLLED
2 RSA5100B Series Hard Drive Upgrades
Kit description
Option 59 kit parts list
Quantity Part number Description
1 ea 075-1056-XX MANUAL, TECH: RSA5KB Option 56 and 59
INSTALLATION INSTRUCTIONS
1 ea 071-2191-XX MANUAL, TECH; SVCPT-UPG; TEKTRONIX
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
1 ea 200-5324-XX COVER; EMPTY DRIVE BAY
4 ea 210-1543-XX SCREW, SHOULDER, SPECIAL; 6-32 (USE WITH
VIBE ISOLATION GROMMETT)
4 ea 211-0510-XX SCREW, MACHINE; 6-32 X 0.375, PNH, ZINC
PLATED STEEL, T15
2 ea 211-0690-XX SCREW, MACHINE; 6-32 X 0.875, PNH, BLACK
ZINC PLATED STEEL, TORX & SLOT
4 ea 348-1835-XX GROMMET; VIBRATION ISOLATION
1 ea 850-0264-XX DRIVE ASSEMBLY; INTERNAL FIXED DRIVE,
PROGRAMMED, RSA5XXXB SERIES
1ea N/A LABEL, MANUFACTURED; PRODUCT LABEL,
SAFETY CONTROLLED
RSA5100B Series Hard Drive Upgrades 3
Removing the installed drives
Removing the installed drives
This section contains all the procedures to remove Option 56 (Removable Hard
Disk Drive) or Option 59 (Internal Hard Disk Drive only) from your instrument.
The section following this one describes the installation of the new drive(s).
Minimum tool and equipment list
The following tools are required to for installation of this kit. All tools are
standard tools that are readily available.
Table 1: Tools required for installation
Item
no. Name Description
1. Screwdriver
handle
(magnetic)
Torque driver handle. Accepts 1/4-in. hex-head driver tips
2. No. 2 Phillips
or Pozidriv tip
Phillips or Pozidriv-driver tip for number 2 size screw heads
3. P-1 Phillips
tip
Phillips driver tip for P-1 size screw heads
4. T-15 TORX
tip
TORX driver tip for T-15 size screw heads
5. T-20 TORX
tip
TORX driver tip for T-20 size screw heads
These instructions are for qualified service personnel who are familiar
with servicing the product. If you need further details for disassembling or
reassembling the product, refer to the RSA5100B Series Real-Time Signal
Analyzers Service Manual, Tektronix part number 077-0903-XX.
Removing a removable hard disk drive (Option 56)
WARNING. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power. Failure to do so could result
in injury or death.
4 RSA5100B Series Hard Drive Upgrades
Removing the installed drives
If you are upgrading from Option 56 to Option 59, you need to remove the drive
assembly from the instrument to begin the upgrade process. Perform the following
steps to remove the removable hard disk.
1. Loosen the thumbscrews securing the drive to the front panel.
2. Grasp the drive assembly by the thumbscrews and pull the drive assembly
straight out of the instrument.
3. Place the removed drive assembly in anti-static packaging and store it in a
protected location for possible future use or discard the drive.
Removing the internal hard drive (Option 59)
NOTE. Right-side or left-side references in these instructions assume you are
viewing the instrument from the front panel.
WARNING. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power. Failure to do so could result
in injury or death.
If you are upgrading from Option 59 (internal hard drive) to Option 56, you have
to remove the internal hard drive from your instrument.
1. Remove the power cord.
2. If it is installed, pull the front cover off the instrument.
3. Remove the two T-15 Torx-head screws that secure the plastic carrying handle
to the side of the instrument. (It is not necessary to remove the black metal
handles.) (See Figure 1.)
4. Remove four T15 Torx-head screws along each side that attach the top and
bottom covers to the instrument, and two T20 screws near the front edge of
the top cover (next to the folding handles).
5. Remove the top and bottom covers. Remove the top cover by pulling it
straight back about 1 inch. Pull out on the sides of the top cover, flexing the
sides slightly to clear the instrument chassis, and pull the top cover away
from the instrument.
6. Remove the eighteen T15 Torx-head screws that secure the top shield to the
chassis and remove the shield.
RSA5100B Series Hard Drive Upgrades 5
Removing the installed drives
Figure 1: Remove covers
6 RSA5100B Series Hard Drive Upgrades
Removing the installed drives
Removing the internal hard
drive
1. Disconnect the two video cables from the PC carrier board. Move the cables
out of the way.
2. Remove the four screws at the corners of the hard disk drive mounting plate
that secure the mounting plate to the instrument.
3. Lift the hard disk drive mounting plate out of the instrument. Disconnect the
SATA cable from the hard disk drive.
4. Remove the four screws that secure the hard disk drive to the mounting plate.
RSA5100B Series Hard Drive Upgrades 7
Installing new drive options
5. Place the removed hard drive in anti-static packaging and store it in a
protected location for possible future use or discard the drive.
NOTE. If you discard or recycle the removed drive, be sure to follow your
organization’s security protocols to ensure the destruction of sensitive data.
6. Reinstall the hard disk drive mounting plate in the chassis.
Installing new drive options
This sections describes how to install your new drive options.
Installing Option 56: Removable hard disk drive
To perform the following procedure you must have already removed option 59
from your instrument. (See page 5, Removing the internal hard drive (Option 59).)
1. Attach the removable hard drive to the removable hard disk drive bracket
(part number 407-5473-XX) with four screws (part number 211-1081-XX)
using a torque driver with a P1 tip. Tighten the screws to 4.0 in-lbs.
2. Attach the removable hard drive label to the removable hard drive bracket.
Start by centering one end of the label and making it flush with the bracket.
Make sure the label is correctly oriented with the bottom of the label aligned
with the bottom of the bracket.
3. Slide the removable hard disk drive assembly into the drive opening and
secure the hard drive with the two thumbscrews.
8 RSA5100B Series Hard Drive Upgrades
Andere Handbücher für RSA5100B series
4
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Tektronix Messgerät Handbücher
Tektronix
Tektronix VM700T Bedienungsanleitung
Tektronix
Tektronix WCA2UP-03 Bedienungsanleitung
Tektronix
Tektronix BPA100 Bedienungsanleitung
Tektronix
Tektronix TCP312 Bedienungsanleitung
Tektronix
Tektronix RSA6120A series Handbuch
Tektronix
Tektronix A621 Bedienungsanleitung
Tektronix
Tektronix RSA3303A Bedienungsanleitung
Tektronix
Tektronix TCP202 Service-Handbuch
Tektronix
Tektronix Keithley 2601B-PULSE Bedienungsanleitung
Tektronix
Tektronix Keithley SourceMeter 2461 Bedienungsanleitung
Tektronix
Tektronix 1401 Bedienungsanleitung
Tektronix
Tektronix A622 Bedienungsanleitung
Tektronix
Tektronix H600 RFHawk Bedienungsanleitung
Tektronix
Tektronix 7D01 Bedienungsanleitung
Tektronix
Tektronix P7260 Bedienungsanleitung
Tektronix
Tektronix OI tek P5200A Series Handbuch
Tektronix
Tektronix RSA306 Gebrauchs- und Pflegehandbuch
Tektronix
Tektronix PRISM MPI2-10 Bedienungsanleitung
Tektronix
Tektronix CSA 803C Bedienungsanleitung
Tektronix
Tektronix AA 501A Bedienungsanleitung
