Tektronix RSA5BUP Bedienungsanleitung

RSA5BUP (Options 65, 66, and 6566)

RSA5UP (Option 5566)

RSA5100A and RSA5100B Series Real-Time Signal Analyzers

Digital I and Q Outputs and Zero Span Output Upgrades

ZZZ

Instructions

www.tektronix.com

*P075106100*

075-1061-00

or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supersedes that in all previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Service safety summary

Only qualiﬁed personnel should perform service procedures. Read this Service

Safety Summary and the General Safety Summary located in the Service Manual

before performing any service procedures.

Do Not Service Alone. Do not perform internal service or adjustments of this

product unless another person capable of rendering ﬁrst aid and resuscitation is

present.

DisconnectPower. To avoid electric shock, switch off the instrument power, then

disconnect the power cord from the mains power.

UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay

exist in this product. Disconnect power, remove battery (if applicable), and

disconnect test leads before removing protective panels, soldering, or replacing

components.

To avoid electric shock, do not touch exposed connections.

RSA5100A/B Series Digital I/Q and Zero Span Upgrades 1

Kit description

This kit describes the installation of the following Options:

RSA5100B Series.

Option 65: Digital I and Q Outputs

Option 66: Zero Span Output

Option 6566: Digital I and Q Outputs and Zero Span Output

RSA5100A Series.

Option 5566: Digital I and Q Outputs and Zero Span Output

Products

RSA5103B. All serial numbers

RSA5106B. All serial numbers

RSA5115B. Allserialnumbers

RSA5126B. All serial numbers

RSA5103A. All serial numbers

RSA5106A. All serial numbers

RSA5115A. Allserialnumbers

RSA5126A. All serial numbers

2 RSA5100A/B Series Digital I/Q and Zero Span Upgrades

Kit description

Kit parts list

The following table provides a list of parts contained in this kit. The kit contains

the same parts, regardless of which of the three options you ordered. The actual

option (or options) available is controlled with the option key provided in the kit.

Quantity Part number Description

1 075-1061-XXMANUAL, TECH INSTALLATION, RSA5BUP OPTIONS 65,

66, 6566

1 171-2191-XX MANUAL,TECH; SVCPT-UPG; TEKTRONIX

SUPPLEMENTAL INFORMATION SHEET FOR

THE PEOPLES REPUBLIC OF CHINA; CHINA ROHS

2 174-5106-XX CABLE, ASSEMBLY (I AND Q OUT, PANEL MOUNT),

SAFETY CONTROLLED

2 174-5195-XX CABLE ASSY ELEC: 2X 50P MDR CONN. 1.5M L, 18

TWIST PAIR, 100 OHM, 1 I/O, 13 GND, W/SHIELD

NOTE. These cables are not needed to install the Option.

They are supplied for external connections to the I and Q

Output connectors.

1 174-5213-XX CABLE ASSY, RIBBON; STATIC GROUND, 1X2; SAFETY

CONTROLLED

1 174-6418-XX CABLE, COAX BNC-ST TO SMB-RA

1 200-5317-XX COVER, REAR PANEL, OPTION (I AND Q / ZERO SPAN)

4 211-0450-XX SCREW, MACHINE; 2.5MM X 0.45 X 6MM, PNH, STEEL,

ZINC PLATED, T8 TORX DRIVE

8 211-1050-XX SCREW, MACHINE; 6-32 X 0.312 L, PNH, STEEL, ZINC

FINISH, T15

1 863-0955-XX CKT BD SUBASSY; REAL TIME IQ AND LOG VIDEO

OUTPUT, FUNCTIONALLY TESTED

1N/A LABEL, EXPORT CONTROL CLASSIFICATION

NOTE. Export control label only applies to RSA5100B

Series instruments when installing Option 65 or Option 6566.

1N/A LABEL, MANUFACTURED; OPTION KEY UPGRADE

LABEL

1N/A LABEL, MANUFACTURED; PRODUCT LABEL, SAFETY

CONTROLLED

RSA5100A/B Series Digital I/Q and Zero Span Upgrades 3

Installation instructions

This section contains all procedures needed to install the required components.

Minimum tool and equipment list

The following tools are required to for installation of this kit. All tools are

standard tools that are readily available.

Item Name Description

1. Screwdriver handle (magnetic) Torque driver. Accepts 14 inch

hex-head driver tips

2. T8 TORX tip TORX driver tip for T-8 size screw

heads

3. T15 TORX tip TORX driver tip for T-15 size screw

heads

4. T20 TORX tip TORX driver tip for T-20 size screw

heads

5. 5/8" hex wrench Open end wrench to install BNC

connector

6. 5/32" hex wrench

NOTE. Only needed for early models

of the RSA5100A Series instruments.

Hex wrench to remove Allen head

screws at front of top cover

These instructions are for qualiﬁed service personnel who are familiar

with servicing the product. If you need further details for disassembling or

reassembling the product, refer to the product’s Service Manual.

Remove cosmetic covers and shield

NOTE. Right-side or left-side references in these instructions assume you are

viewing the instrument from the front panel.

WARNING. To avoid electric shock, switch off the instrument power, then

disconnect the power cord from the mains power. Failure to do so can cause

injury or death.

1. Remove the power cord.

2. If it is installed, pull the front cover off the instrument.

4 RSA5100A/B Series Digital I/Q and Zero Span Upgrades

Installation instructions

3. Remove the two T15 Torx-head screws that secure the plastic carrying handle

to the side of the instrument. (It is not necessary to remove the black metal

handles.) (See Figure 1.)

4. Remove four T15 Torx-head screws along each side that secure the top and

bottom covers to the instrument, and two T20 Torx-head screws near the front

edge of the top cover (next to the folding handles).

NOTE. Early models of the RSA5100A Series instruments used four 5/32″Allen

socket cap screws in place of the T15 Torx-head screws.

5. Remove the top and bottom covers. Remove the top cover by pulling straight

back about 1 inch. Then pull out on the sides of the top cover outward,

ﬂexing them slightly to clear the instrument chassis, and pull it away from the

instrument.

6. Remove the eighteen T15 Torx-head screws that secure the top shield to the

chassis and remove the shield.

RSA5100A/B Series Digital I/Q and Zero Span Upgrades 5

Installation instructions

Figure 1: Remove covers

6 RSA5100A/B Series Digital I/Q and Zero Span Upgrades

Installation instructions

Attach cables to rear-panel cover insert

1. Install the cables to the new rear-panel cover provided in this kit. (See

Figure 2.)

Install the two IQ Output ribbon cables onto the rear panel cover using

four T8 Torx-head screws provided in the kit. Tighten the screws using a

torque driver set to 5.5 in-lb.

Install the Ground cable onto the spade connector on the rear-panel cover.

Install the Zero Span Output BNC cable to the rear-panel cover. Use the

BNC washer and 5/8″nut that is provided with the BNC connector.

Figure 2: Installing cables

RSA5100A/B Series Digital I/Q and Zero Span Upgrades 7

Installation instructions

Install rear panel cover insert into instrument

1. Remove the blank, rear-panel cover from the chassis (attached with eight T15

Torx-head screws). Discard the blank panel.

2. Install the new rear-panel cover (with attached cabling) on the rear panel

chassis using eight T15 Torx-head screws. Torque these screws to 10.0 in/lb.

(See Figure 3.)

Figure 3: Installing the rear panel cover on the rear panel of the chassis

8 RSA5100A/B Series Digital I/Q and Zero Span Upgrades

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tektronix Messgerät Handbücher

Tektronix

Tektronix WVR5200 Series Bedienungsanleitung

Tektronix

Tektronix KEITHLEY 2450-EC Bedienungsanleitung

Tektronix

Tektronix DAS NT Option 04 Bedienungsanleitung

Tektronix

Tektronix P7350 Bedienungsanleitung

Tektronix

Tektronix RSA5100B series Referenzhandbuch

Tektronix

Tektronix 1401A Bedienungsanleitung

Tektronix

Tektronix RSA6100A Series Bedienungs- und Wartungshandbuch

Tektronix

Tektronix FCA3000 Series Bedienungs- und Wartungshandbuch

Tektronix

Tektronix P6900 Series Bedienungsanleitung

Tektronix

Tektronix TTR500 series Bedienungsanleitung

Tektronix

Tektronix H600 RFHawk Bedienungsanleitung

Tektronix

Tektronix P6202A Bedienungsanleitung

Tektronix

Tektronix WFM2300 Bedienungsanleitung

Tektronix

Tektronix RSA3408A Bedienungsanleitung

Tektronix

Tektronix VM700A VMTB Bedienungsanleitung

Tektronix

Tektronix DSA8300 Gebrauchs- und Pflegehandbuch

Tektronix

Tektronix Series Handbuch

Tektronix

Tektronix 1741C Bedienungsanleitung

Tektronix

Tektronix SDA601 Bedienungsanleitung

Tektronix

Tektronix RSA5100A Series Bedienungsanleitung

Tektronix

Tektronix 7L5 Bedienungsanleitung

Tektronix

Tektronix TMSSC2 Bedienungsanleitung

Tektronix

Tektronix RSA5100A Series Handbuch

Tektronix

Tektronix LumaColor II J18 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung