Tektronix WVR6UP Bedienungsanleitung

Instructions

WVR6UP, WVR70UP, and WVR7UP Upgrades

WVR6100, WVR7000, and WVR7100 Series

Waveform Rasterizers

075-0887-03

*P075088703*

075088703

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to all safety summaries prior to

performing service.

www.tektronix.com

suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

HIn North America, call 1-800-833-9200.

HWorldwide, visit www.tektronix.com to find contacts in your area.

WVR6UP, WVR70UP, and WVR7UP Upgrades 1

Service Safety Summary

Only qualified personnel should perform service procedures. Read this Service

Safety Summary and the General Safety Summary in the product service manual

or the instruction manual.

Do Not Service Alone. Do not perform internal service or adjustments of this

product unless another person capable of rendering first aid and resuscitation is

present.

Disconnect Power. To avoid electric shock, switch off the instrument power, then

disconnect the power cord from the mains power.

Use Care When Servicing With Power On. Dangerous voltages or currents may

exist in this product. Disconnect power, remove battery (if applicable), and

disconnect test leads before removing protective panels, soldering, or replacing

components.

To avoid electric shock, do not touch exposed connections.

Service Safety Summary

2WVR6UP, WVR70UP, and WVR7UP Upgrades

WVR6UP, WVR70UP, and WVR7UP Upgrades 3

Kit Description

These instructions support field installation of all options currently available for

field installation in the WVR6100, WVR7000, and WVR7100 Waveform

Rasterizers. Find your kit in the table of kits supported that follows.

CAUTION. To prevent monitoring problems, after installing any audio option in

this kit, do not use the optional accessory, Analog/Audio Breakout Cable

Assembly, Tektronix part number 012-1658-01. This optional accessory is for

rasterizers that shipped with early versions of audio option hardware and will

not work properly with your new audio option. You can order part number

012-1688-00, which is an Analog/Audio Breakout Cable Assembly that will work

with your new audio option.

Kit Description

WVR70UP-SD Field inst

lls O

tion SD,

dds su

ort for st

rd-de

inition

ideo

WVR7UP-SD

signal monitoring to the WVR7000 or WVR7100.

WVR70UP-DS

WVR6UP-DS

WVR7UP-DS

Field installs Option DS, which adds support for Digital audio monitoring of

embedded audio and audio signals in the AES/EBU inputs.

WVR70UP-AD

Field installs Option AD, which adds support for Analog audio and Digital

WVR7UP-AD

omon

tor

ng o

inputs.

WVR6UP-DD

Field installs Option DD, which adds support for Dolby Digital (AC-3) decode

omon

tor

ng o

signals in the AES/EBU inputs.

WVR6UP-DDE

Field installs Option DDE, which adds support for Dolby E decode, Dolby

(

)

(

-- 3

)

omon

tor

ng o

embedded audio and audio signals in the AES/EBU inputs.

WVR6UP-EYE

WVR7UP-EYE Field installs Option EYE, which adds support for eye pattern monitoring of

the physical layer of video signals. WVR6100 instruments display eye

;

tterns

or SD sign

ls;

R7100

or HD sign

ls.

R7100 instruments

also display eye patterns for SD signals if equipped with Option SD. (See

entry for WVR7UP--SD in this table.)

WVR6UP-PHY

WVR7UP-PHY

Field installs Option PHY, which adds all of the capabilities of Option EYE

plus support for automated eye parameters measurement and jitter

orm dis

R6100 instruments dis

itter w

orms

or SD

signals; WVR7100 for HD signals. WVR7100 instruments also display jitter

waveforms for SD signals when equipped with Option SD. (See entry for

WVR7UP-SD in this table)

Kit Description

4WVR6UP, WVR70UP, and WVR7UP Upgrades

Products

WVR6100 Waveform Rasterizer All instruments

WVR7000 Waveform Rasterizer All instruments

WVR7100 Waveform Rasterizer All instruments

Minimum Tool and Equipment List

Required tools and equipment Part number

Screwdriver handle. Accepts TORX-driver bits. General tool. Used for

audio and EYE display options.

T-10 TORX drive bit. Used for removing the rasterizer top cover. Used

for audio and EYE display options.

T-15 TORX drive bit. Used for removing most of the screws on the

rasterizer. Used for audio and EYE display options.

3/16 Nutdriver. Used for removing and installing audio option boards

for audio options only that have analog audio I/O connector.

5/16 Nutdriver. Used for loosening and tightening the nuts that secure

the fan bracket when installing a new Power Supply cable.

1/4 Nutdriver. Used for removing or installing internal audio board

mounting posts. Used for audio and EYE display options.

A standard PC running Windows 98, Windows NT 4.0, Windows ME,

Windows 2000, or Windows XP. Used for installing all options.

Winsock 2.0, an Ethernet interface, and 10 MB of free disk space

must be present on the PC system. Used for installing all options.

Kit Description

WVR6UP, WVR70UP, and WVR7UP Upgrades 5

Kit Parts Lists

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep

1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors

8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick

3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T--15 TORX drive

8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562

1 each 671-6072-XX Circuit-board assembly; Digital Audio

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep

1 each 131-7430-XX Connector, DSUB; male, 62 pins, 0.100 center, 30 gold

1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors

8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick

3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T--15 TORX drive

2 each 214-3903-XX Screw; 4--40 X 0.312 long, 0.188 H hex head stand off

8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562

1 each 671-9938-XX Circuit-board assembly; Digital Analog Audio

WVR7UP-SD

WVR70UP-SD

WVR6UP-DS

WVR70UP-DS

WVR7UP-DS

WVR6UP-AD

WVR70UP-AD

WVR7UP-AD

Kit Description

6WVR6UP, WVR70UP, and WVR7UP Upgrades

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep

1 each 131-7430-XX Connector, DSUB; male, 62 pins, 0.100 center, 30 gold

1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors

8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick

3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T--15 TORX drive

2 each 214-3903-XX Screw; 4--40 X 0.312 long, 0.188 H hex head stand off

8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562

1 each 671-9938-XX Circuit-board assembly; Digital Analog Audio

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

1 each 119-7167-XX Circuit-board assembly; Dolby E/Digital Decoder Module;

72 PIN SIMM

3 each 129-1570-XX Post, spacer; 1.385 X 0.250 X 0.375 deep

1 each 131-7430-XX Connector, DSUB; male, 62 pins, 0.100 center, 30 gold

1 each 174-4973-XX Cable assembly 80 POS. Cable with two 2X40 connectors

8 each 210-1039-XX Washer, lock; 0.521 ID; 0.025 thick

3 each 211-0722-XX Screw; 6--32 X 0.250, panhead T--15 TORX drive

2 each 214-3903-XX Screw; 4--40 X 0.312 long, 0.188 H hex head stand off

8 each 220-0497-XX Nut; hex; 0.5--28 X 0.562

1 each 671-9938-XX Circuit-board assembly; Digital Analog Audio

WVR6UP-DD

WVR7UP-DD

WVR6UP-DDE

WVR7UP-DDE

Kit Description

WVR6UP, WVR70UP, and WVR7UP Upgrades 7

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female

1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards

1 each 174-5301-00 Coaxial cable, SMA

1 each 671-6099-XX Circuit board subassembly; SD, Eye board

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female

1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards

2 each 174-5301-00 Coaxial cable, SMA

1 each 679-9935-XX Circuit board subassembly; Loop-through board

1 each 671-9936-XX Circuit board subassembly; HD/SD, Eye board

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female

1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards

1 each 174-5301-00 Coaxial cable, SMA

1 each 671-6099-XX Circuit board subassembly; SD, Eye board

Quantity Part number Description

1 each 020-2612-XX Documents CD

1 each 075-0887-XX Kit instructions

5 each 129-1604-XX Hardware; spacer post, .309 L, 6--32 male, 4--40 female

1 each 174-5224-XX Cable assembly, Power Supply to Main and Eye boards

2 each 174-5301-00 Coaxial cable, SMA

1 each 679-9935-XX Circuit board subassembly; Loop-through board

1 each 671-9936-XX Circuit board subassembly; HD/SD, Eye board

WVR6UP-EYE

WVR7UP-EYE

WVR6UP-PHY

WVR7UP-PHY

Kit Description

8WVR6UP, WVR70UP, and WVR7UP Upgrades

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tektronix Messgerät Handbücher

Tektronix

Tektronix RSA5100B series Referenzhandbuch

Tektronix

Tektronix IsoVu TIVM Series Bedienungsanleitung

Tektronix

Tektronix P6248 Bedienungsanleitung

Tektronix

Tektronix TLA7PG2 Montage- und Wartungsanleitung

Tektronix

Tektronix 5D10 Bedienungsanleitung

Tektronix

Tektronix ATECTekRanger Bedienungsanleitung

Tektronix

Tektronix RSA306B Bedienungsanleitung

Tektronix

Tektronix RSA3303A Bedienungsanleitung

Tektronix

Tektronix DSA8300 Handbuch

Tektronix

Tektronix RSA5100A Series Bedienungsanleitung

Tektronix

Tektronix RSA3408B Bedienungsanleitung

Tektronix

Tektronix WVR6100 Series Bedienungsanleitung

Tektronix

Tektronix 7L12 Bedienungsanleitung

Tektronix

Tektronix 7D01 Bedienungsanleitung

Tektronix

Tektronix 492, 492P Bedienungsanleitung

Tektronix

Tektronix P7330 Bedienungsanleitung

Tektronix

Tektronix P6910 Bedienungsanleitung

Tektronix

Tektronix P8018 Bedienungsanleitung

Tektronix

Tektronix CSA8000B Series Bedienungsanleitung

Tektronix

Tektronix KEITHLEY 4200A-SCS-PK2 Bedienungsanleitung

Tektronix

Tektronix 2715 Bedienungsanleitung

Tektronix

Tektronix 1502 Bedienungsanleitung

Tektronix

Tektronix TLA 7M3 Handbuch

Tektronix

Tektronix VM700T Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung