Teldat VisorALARM+ Bedienungsanleitung

VisorALARM+

Alarm Receiver over IP

QUICK INSTALLATION GUIDE

Dm377-I, Version: 1.0

1. Introduction

This Quick Installation Guide is designed to help the installation process of the VisorALARM+ and is

geared to quick reference and initial configuration; therefore this document contains information specific to

this aim and does not consider all possibilities. For further information on this please see the

VisorALARM+ installation manual or contact the Teldat Securitytechnical service.

2. Requirements

Automation software

•Automation Software compatible with Surgard, Radionics 6500 or Ademco 685 receivers and

an available RS-232 line.

Connections

•Connection to an Ethernet network (10 or 100 Mbps).

•Power connection 110-240 V AC.

Configuration

•PC with serial port (speed 9600, 8 data bits, without paritybits, 1 stop bit and without flow

control) and terminal emulation software (e.g. Windows HyperTerminal).

•RS serial cable for configuration (DB9 male – DB9 female).

Internet Connection

•Static and public1IP address for the VisorALARM+.

1IfInternetaccess is behind a NAT / firewall, you musthave a private static IP address and a UDP portredirected to the said private address.

3. Checklist

a. Cables:

•Standard Ethernet network cable, category5.

•AC power supplycable.

•RS-232 serial cable for configuration (DB9 male – DB9 female).

•RS-232 serial cable for transmission of alarms to the server (DB9 male – DB9 female).

b. Receiver Data:

•Type of receiver to emulate (Surgard, Radionics 6500 or Ademco 685).

•Line and receiver identifier.

c. IP Information:

•Default address, subnet mask and gateway.

•UDP port for alarm reception.

d. RS-232 communication parameters: speed, data bits, paritybits and stop bit.

4. Physical Connections

1. Connect one end of the Ethernet network cable to the connector labeled LAN and the other end to

a switch or a hub in your network.

2. Connect the female end of the configuration RS-232 cable to the PC serial port and the male end

to the connector labeled AUX on the rear panel of the VisorALARM+.

3. Connect the DB25 end of the data RS.232 cable to the AUT connector and the other end to the

computer with the automation software.

4. Ifyou have aprinter connect the DB25 end of the printer RS232 cable to the PRN connector and

the other end to the serial printer.

5. Connect the female end of the power supplycable to the power connector of the device and the

male end to a grounded socket.

5. Configuration

Switch on the device. Inthe PC terminal emulator, you will see some information on device start-up.

Wait until information similar to that shown belowis displayed:

Router model VISORALARM-PLUS EU 6 119 CPU MPC8260 S/N: 472/01349

2 LAN, 4 WAN Lines

CIT software version: 10.6.33 Feb 26 2007 14:18:00

Atthis point the device is readyto be configured. The commands required for configuration are

described belowand grouped byfunctionality.

Starting with default config

When you receive the device from factoryit is shipped with abasic default configuration. Ifyou wish

to defaults the device to this factoryconfiguration use the ‘set default-config’ command.

*p 4

Config>set default-conf

All your session changes will be lost.

Activate default configuration (Yes/No)?Y

Config>

Configuring IP

Enter the following commands, substituting ip_address for the VisorALARM+ IPaddress, mask for

its network mask and gateway for the gatewayIP address.

Config>protocol ip

-- Internet protocol user configuration --

IP config>address ethernet0/0 ip_address mask

IP config>route 0.0.0.0 0.0.0.0 gateway 1

IP config>classless

IP config>exit

Config>

Configuring the type of AlarmReceiver

Configure the udp-port for the alarm receiver. This is the receiver UDP port where the mIPdevices

will send its registration and supervision data packets.

Config>network serial0/0

-- ARLY Interface Configuration --

ARLY-1 Cfg>supervision port udp-port

Parameters dependent on the emulated receiver: the commands required to configure the emulation of

the different receivers with their default parameters for communication with the automation server are

displayed below:

Sur Gard MLR-2000 / MLR2E

ARLY-1 Cfg> alarm-receiver protocol sur-gard

ARLY-1 Cfg> alarm-receiver parameters r=0

ARLY-1 Cfg> alarm-receiver receiver-id 01

ARLY-1 Cfg> alarm-receiver line-id 001

Sur Gard DLR-2

ARLY-1 Cfg> alarm-receiver protocol sur-gard

ARLY-1 Cfg> alarm-receiver parameters r=1

ARLY-1 Cfg> alarm-receiver receiver-id 01

ARLY-1 Cfg> alarm-receiver line-id 1

Radionics 6500

ARLY-1 Cfg> alarm-receiver protocol radionics-6500

ARLY-1 Cfg> alarm-receiver receiver-id 01

ARLY-1 Cfg> alarm-receiver line-id 1

ARLY-1 Cfg> alarm-receiver parameters h=0

Ademco 685: if you do not wish to use the ACK/NACKprotocol, eliminate the second line.

ARLY-1 Cfg> alarm-receiver protocol ademco-685

ARLY-1 Cfg> alarm-receiver receiver-id 1

ARLY-1 Cfg> alarm-receiver line-id 1

Ifyou need to configure another receiver or line id numbers please replace in the ‘alarm-receiver

receiver-id’ and alarm-receiver line-id’ commands the parameters that appear with identifier 1with

your desired numbers keeping the length of the field.

Configuring the configuration pattern for MIP installation

Aquick configuration process exists to simplifythe installation process for newMIPs. Here a

minimum number of parameters are manuallyconfigured in the MIPand, subsequently,a‘register’

operation is executed using an installer password. The MIPreceives the configuration of the

configuration pattern during this process, where the installer password coincides with that provided.

Belowyou will see aconfiguration pattern displayed with installer password 1111.For further

information on each of these parameters, please see the VisorALARM+ Installation manual.

ARLY-1 Cfg> cfg-pattern 1 default

ARLY-1 Cfg> cfg-pattern 1 instalator-password 1111

ARLY-1 Cfg> cfg-pattern 1 usr-password 1234

ARLY-1 Cfg> cfg-pattern 1 mip-password ZYXW5678

ARLY-1 Cfg> cfg-pattern 1 receiver-password WXYZ4321

ARLY-1 Cfg> cfg-pattern 1 keep-alive-timer 45

ARLY-1 Cfg> cfg-pattern 1 keep-alive-retries 3

ARLY-1 Cfg> cfg-pattern 1 keep-alive-retries-timer 2

ARLY-1 Cfg> cfg-pattern 1 phone-length 9

ARLY-1 Cfg> cfg-pattern 1 alarm-tx-retries 2

ARLY-1 Cfg> cfg-pattern 1 callback-phone 918076565

ARLY-1 Cfg> cfg-pattern 1 bck-receiver-IP 80.26.96.183

ARLY-1 Cfg> cfg-pattern 1 bck-keep-alive-timer 45

ARLY-1 Cfg> cfg-pattern 1 bck-keep-alive-retries 3

ARLY-1 Cfg> cfg-pattern 1 bck-keep-alive-retries-timer 2

Configuring events

ARLY-1 Cfg>exit

Config>event

-- ELS Config --

ELS config> enable trace subsystem ARLY ALL

ELS config>exit

Configuring the speed of the UD communication ports

To set the speed for the UD com1 port use the next command replacing the portSpeed parameter by

the desired port speed.

Config>net serial1/0

MODEMEMU-serial1/0 Cfg>speed portSpeed

MODEMEMU-serial1/0 Cfg>exit

Config>

Toset the speed for the UD com2 port use the next command replacing the portSpeed parameter by

the desired port speed.

Config>net serial1/1

MODEMEMU-serial1/1 Cfg>speed portSpeed

MODEMEMU-serial1/1 Cfg>exit

Config>

Finallysave the configuration and restart in order to activate the newsettings. Ifyou wish to check

the configuration, the “show config”command will displaythe configuration from the menu

where this is located together with all its submenus.

Config> save

Save configuration (Yes/No) [No]? y

OK on Flash (not saved in SmartCard)

Config>[CTRL-P]

*restart

Are you sure to restart the system(Yes/No)? y

Restarting. Please wait ................................

Teldat Corp.

1111 Brickell Ave., Suite 1100

Miami, FL 33131

800.4TELDAT / 305.372.3480

www.teldatsecurity.com

Technical Support: [email protected]

Inhaltsverzeichnis

Andere Teldat Empfänger Handbücher

Teldat

Teldat VisorALARM PLUS 2U Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung