Teltonika FMM640 Leitfaden

https://wiki.teltonika-gps.com/view/FMM640_Mounting_recommendations

FMM640 Mounting recommendations

Main Page > EOL Products > FMM640 > FMM640 Manual > FMM640 Mounting recommendations

Connecting Wires

• Wires should be connected while module is not plugged in.

• Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and

moving objects near the wires.

• The connections should not be seen very clearly. If factory isolation was removed while connecting

wires, it should be applied again.

• If the wires are placed in the exterior or in places where they can be damaged or exposed to heat,

humidity, dirt, etc., additional isolation should be applied.

• Wires cannot be connected to the board computers or control units.

Connecting Power Source

• Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending

on car, this may happen in 5 to 30 minutes period.

• When module is connected, be sure to measure voltage again if it did not decrease.

• It is recommended to connect to the main power cable in the fuse box.

• Use 3A, 125V external fuse.

Connecting Ignition Wire

• Be sure to check if it is a real ignition wire – power does not disappear while starting the engine.

• Check if this is not an ACC wire (when key is in the first position, most electronics of the vehicle

are available).

• Check if power is still available when you turn off any of vehicles devices.

• Ignition is connected to the ignition relay output. As alternative, any other relay, which has power

output, when ignition is on, may be chosen.

Connecting Ground Wire

• Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.

• If the wire is fixed with the bolt, the loop must be connected to the end of the wire.

• For better contact scrub paint from the place where loop is connected.

PAY ATTENTION! Connecting the power supply must be carried out in a very low impedance point

on-board vehicle network. These points in the car are the battery terminals. Therefore, we

recommend connecting the power of FMM640 (wire GND and POWER) directly to the battery

terminals. Another valid option is to connect the wires to the main POWER cable inside the fuse box

(if there is none, then to the power supply where the fuses of vehicle’s computer are), wire GND

must be connected in a special point, designed to connect GND vehicle computer. Connecting the

GND at an arbitrary point to the mass of the car is unacceptable, as static and dynamic potentials on

the line GND will be unpredictable, which can lead to unstable FMM640 and even its failure.

Connecting Antennas

• Gently connect antennas to device by hands, without using additional equipment like pliers. The

tightening torque for fixing the connector must be up to 0.5 – 0.7 Nm (‘handtightened’).

• When placing antennas avoid easily reached places.

• Avoid GNSS antenna placement under metal surfaces.

• Avoid placing FMM640 device near car radio, speakers or alarm systems.

• GNSS antenna must be placed so its state is as horizontal as possible (if antenna is leant more than

30 degrees, it is considered incorrect mounting).

• GNSS antenna cable cannot be bent more than 80 degrees.

• GNSS antenna must be placed sticker facing down.

It is recommended to place GNSS antenna behind dashboard as close to the window as possible. A

good example of GNSS antenna placement is displayed in a picture below (area colored green).

Module Installation

• Module should not be seen or easily reached.

• Module should be firmly fixed to the surface or cables.

• Module cannot be fixed to heat emitting or moving parts.

• SIM card should be inserted in the module while the connector is plugged off (while module has no

power).

Andere Handbücher für FMM640

Inhaltsverzeichnis

Andere Teltonika GPS Handbücher

Teltonika

Teltonika GH4000 Bedienungsanleitung

Teltonika

Teltonika FMU130 Bedienungsanleitung

Teltonika

Teltonika GH1200 Bedienungsanleitung

Teltonika

Teltonika GH120 Series Bedienungsanleitung

Teltonika

Teltonika TMT250 Installationsanleitung

Teltonika

Teltonika FMC130 Installationsanleitung

Teltonika

Teltonika FMB122 Installationsanleitung

Teltonika

Teltonika FMB003 Bedienungsanleitung

Teltonika

Teltonika GH5200 Bedienungsanleitung

Teltonika

Teltonika FM5300 Bedienungsanleitung

Teltonika

Teltonika FM2100 Bedienungsanleitung

Teltonika

Teltonika FMB910 Installationsanleitung

Teltonika

Teltonika TAT140 Bedienungsanleitung

Teltonika

Teltonika FMB001 Bedienungsanleitung

Teltonika

Teltonika FMP100 Bedienungsanleitung

Teltonika

Teltonika FMB965 Installationsanleitung

Teltonika

Teltonika GH4000 Montageanleitung

Teltonika

Teltonika FMB003 Bedienungsanleitung

Teltonika

Teltonika FM3612 Bedienungsanleitung

Teltonika

Teltonika AT1000 Bedienungsanleitung

Teltonika

Teltonika FMC00A Installationsanleitung

Teltonika

Teltonika FM3622 Bedienungsanleitung

Teltonika

Teltonika FMB910 Installationsanleitung

Teltonika

Teltonika FMB900 Installations- und Benutzerhandbuch

Beliebte GPS Handbücher anderer Marken

Raven

Raven Cruizer II Handbuch

Hama

Hama 53118 Bedienungsanleitung

Garmin

Garmin SOUNDER 125 Bedienungsanleitung

Garmin

Garmin DEZL 580 Bedienungsanleitung

Jigabot

Jigabot EX Bedienungsanleitung

Pointer

Pointer Cellocator CelloTrack XT LTE Installationsanleitung

Queclink

Queclink GV55LITE Bedienungsanleitung

Voxson

Voxson Voxtrack GPS500 Gebrauchsanweisung

Garmin

Garmin ECHOMAP PLUS Bedienungsanleitung

Starcom Systems

Starcom Systems Kylos Compact Bedienungsanleitung

Garmin

Garmin 15 H Series Bedienungsanleitung

Cobra

Cobra Marine MC 600Ci Bedienungsanleitung

Cellocator

Cellocator CelloTrack T Bedienungsanleitung

Enfora

Enfora Mini-MT GSM2228UG001 Bedienungsanleitung

Magellan

Magellan eXplorist 100 Bedienungsanleitung

LTE

LTE G50B Bedienungsanleitung

Garmin

Garmin DEZL OTR500 Bedienungsanleitung

SkyGolf

SkyGolf SkyCaddie SG1 Bedienungsanleitung