Teltonika FMM880 Bedienungsanleitung
https://wiki.teltonika-gps.com/view/FMM880_First_Start
FMM880 First Start
Main Page > Fast & Easy Trackers > FMM880 > FMM880 First Start
Special and small waterproof LTE CAT M1 GNSS tracker.
Contents
1 Know your device
2 Pinout
3 Set up your device
3.1 How to insert Micro-SIM card and connect the battery
3.2 PC Connection (Windows)
3.3 How to install USB drivers (Windows)
3.4 Configuration (Windows)
3.5 Quick SMS configuration
4 Quick installation guide
5 Mounting recommendations
6 Safety information
Know your device
Pinout
PIN
NUMBER PIN NAME DESCRIPTION
1VCC (10-30)V
DC (+)
(Red) Power supply
(+10-30 V DC)
2GND (-) (Black) Ground
Set up your device
How to insert Micro-SIM card and connect the battery
Unscrew 6 screws counterclockwise.1.
Remove the cover.2.
Insert Micro-SIM card as shown with PIN request disabled or read Security info how to3.
enter it later with Teltonika Configurator. Make sure that Micro-SIM card cut-off corner is
pointing forward to slot.
Connect the battery as shown to device. Position the battery in place where it does not4.
obstruct other components.
After configuration, see PC Connection (Windows), attach device cover back and screw in all5.
screws.
Device is ready to be mounted.6.
Micro-SIM card insertion/removal must be performed when device is powered off –
external voltage and battery are disconnected. Otherwise Micro-SIM card might be
damaged or device will not detect it.
PC Connection (Windows)
Power-up FMM880 with DC voltage 10-30 V power supply using power cable. LED’s should1.
start blinking, see “FMM880 LED status”.
Connect device to computer using Micro-USB cable or Bluetooth connection:2.
Using Micro-USB cable
You will need to install USB drivers, see "How to install USB drivers
(Windows)"
Using Bluetooth
FMM880 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then
select Add Bluetooth or other device > Bluetooth. Choose your device named –
“FMM880_last_7_imei_digits”, without LE in the end. Enter default password
5555, press Connect and then select Done.
You are now ready to use the device on your computer.3.
How to install USB drivers (Windows)
Please download COM port drivers from here.1.
Extract and run TeltonikaCOMDriver.exe.2.
Click Next in driver installation window.3.
In the following window click Install button.4.
Setup will continue installing the driver and eventually the confirmation window will appear.5.
Click Finish to complete the setup.
Configuration (Windows)
At first FMM880 device will have default factory settings set. These settings should be changed
according to the user's needs.
Main configuration can be performed via Teltonika Configurator software. Get the latest FMM880
Configurator version from here. Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct version installed.
MS .NET requirements
Operatin
g system
MS .NET
Framework version Version Link
•
Windows
Vista
•
Windows
7
•
Windows
8.1
•
Windows
10
MS .NET
Framework 5.0
32 and
64 bit
.NET
Fram
ewor
k
Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe.
After launch software language can be changed by clicking in the right bottom corner:
Configuration process begins by pressing on connected device:
After connection to Configurator Status window will be displayed:
Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc.
FMM880 has one user editable profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to device using Save to device button.
Main buttons offer following functionality:
Load from device – loads configuration from device.1.
Save to device – saves configuration to device.2.
Load from file – loads configuration from file.3.
Save to file – saves configuration to file.4.
Update firmware – updates firmware on device.5.
Read records – read records from device.6.
Reboot device – restarts device.7.
Reset configuration – sets device configuration to default.8.
Most important configurator section is GPRS – where all your server and GPRS settings can be
configured and Data Acquisition – where data acquiring parameters can be configured. More
details about FMM880 configuration using Configurator can be found here.
Quick SMS configuration
Default configuration has optimal parameters present to ensure best performance of track quality
and data usage.
Quickly set up your device by sending this SMS command to it:
" setparam
2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"
GPRS settings:
2001 – APN
2002 – APN username (if there are no APN username, empty field should be left)
2003 – APN password (if there are no APN password, empty field should be left)
Server settings:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)
Note: Before SMS text, two space symbols should be inserted.
Default configuration settings
Movement and ignition detection:
Vehicle movement will be detected
by accelerometer
Ignition will be detected by
vehicle power voltage
between 13,2 – 30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes Vehicle turns 10° degrees
Vehicle drives 100 meters
Speed difference between
last coordinate and current
position is greater than 10
km/h
Device makes a record On Stop if:
1 hour passes while vehicle is
stationary and ignition is off
Records sending to server:
If device has made a record it is
sent to the server every 120
seconds
After successful SMS configuration, FMM880 device will synchronize time and update records to
configured server. Time intervals and default I/O elements can be changed by using Teltonika
Configurator or SMS parameters.
Quick installation guide
Mounting recommendations
Double sided tape on the back
Example of device mounting
Device fastening
Locate the battery in your vehicle. If present remove the battery cover to access the battery.
Wipe clean the installation surface of the battery if any dust or dirt is visable.
There is a double sided tape on the back of the device, use it to attach the device on the
battery, so that the GNSS antenna and LEDs indicators are facing up.
Connecting power wire
Device power wire is designed to be directly connected to the positive terminal fastener of the
vehicle battery.
Connecting ground wire
Device ground wire is designed to be directly connected to the negative terminal fastener of
the vehicle battery.
Safety information
This message contains information on how to operate FMM880 safely. By following these
requirements and recommendations, you will avoid any dangerous situations. You must read these
instructions carefully and follow them strictly before operating the device!
The device uses a 10 V...30 V DC power supply. The nominal voltage is 12 V DC. The allowed
range of voltage is 10 V...30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package.
Before dismounting the device from the vehicle, ignition MUST be OFF.
Do not disassemble the device. If the device is damaged, the power supply cables are
not isolated or the isolation is damaged, DO NOT touch the device before unplugging
the power supply.
All wireless data transferring devices produce interference that may affect other
devices which are placed nearby.
The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with autonomic power supply.
The device is susceptible to water and humidity if the device housing is not properly
closed.
Installation and/or handling during a lightning storm is prohibited.
Teltonika is not responsible for any harm caused by wrong cables used for connection
between PC and FMM880
Risk of explosion if battery is replaced by an incorrect type.
Battery should not be disposed of with general household waste. Bring damaged or
worn-out batteries to your local recycling center or dispose them to battery recycle bin
found in stores.
https://teltonika-gps.com/product/fmm880/
Andere Handbücher für FMM880
1
Inhaltsverzeichnis
Andere Teltonika GPS Handbücher
Teltonika
Teltonika FMC00A Bedienungsanleitung
Teltonika
Teltonika FMB910 Installationsanleitung
Teltonika
Teltonika FMB910 Installationsanleitung
Teltonika
Teltonika FMB230 Bedienungsanleitung
Teltonika
Teltonika FMB110 Bedienungsanleitung
Teltonika
Teltonika FMB125 Bedienungsanleitung
Teltonika
Teltonika FM3001 Installationsanleitung
Teltonika
Teltonika FM5500 Bedienungsanleitung
Teltonika
Teltonika GH3000 Handbuch
Teltonika
Teltonika TMT250 Bedienungsanleitung
Teltonika
Teltonika FMB010 Bedienungsanleitung
Teltonika
Teltonika FM1110 Bedienungsanleitung
Teltonika
Teltonika FMB140 Installationsanleitung
Teltonika
Teltonika Telematics FMM650 Installationsanleitung
Teltonika
Teltonika FMB208 Installationsanleitung
Teltonika
Teltonika FMB125 Bedienungsanleitung
Teltonika
Teltonika FMB920 Bedienungsanleitung
Teltonika
Teltonika GH3000 Bedienungsanleitung
Teltonika
Teltonika FMB920 Installationsanleitung
Teltonika
Teltonika FMB010 Bedienungsanleitung
