Tennant 6100 Schulungshandbuch
IB 340480 (5-01) 1
No. 340480
Machine: 6100, 6200
Published: 5-01/00
System: SWEEPING
INSTRUCTION BULLETIN
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts
List in the appropriate place in your machine manual for future reference.
Retaining the Parts List will make it easier to reorder individual parts and will
save you the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 384169
SYNOPSIS / PROBLEM:
This kit contains the parts needed to replace the damper solenoid on the model
sweeper/scrubber.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: 1/2” Rounded file
(Estimated time to complete: 1 hour)
PREPARATION:
(Refer to FIG. 1 thru 4)
FOR SAFETY: Before leaving or servicing machine, stop on level surface and set parking
brake. Then turn off machine and remove key.
1. Raise the operator seat and secure in place with the seat support rod.
2. Disconnect battery cables from machine.
WARNING: Always disconnect battery cables from machine before working
on electrical components.
6100 INSTALLATION:
(Refer to FIG. 1 and 2)
1. Remove the hopper from the rear of the machine.
2. Unlatch and lower the filter to gain access to the damper solenoid.
3. Disconnect the solenoid from the main wire harness.
4. Locate the damper solenoid mounted on the side of the damper. Remove and discard the
pin retainers, both retaining pins and the connecting link. (Refer to FIG. 1)
5. Remove and discard the solenoid from the weldment on the side of the cylinder.
(Refer to FIG. 1)
IB 340480 (5-01)2
Remove pin retainers and
both retaining pins from link. Remove and discard old
solenoid from weldment.
FIG. 1 -- DAMPER SOLENOID REMOVAL, 6100
6. File down the flat edge of the D shaped solenoid mounting hole, until the mounting hole is
round.
7. Mount the new solenoid (1) in the new round solenoid mounting hole. (Refer to FIG. 2)
8. Connect one end of the new link (2) to the new solenoid (1) with a new pin (3) and pin
retainers (4). Connect the other end of the link (2) to the damper rod with a new pin (3) and
pin retainers (4). (Refer to FIG. 2)
9. Connect the new solenoid to the main harness.
10. Raise the filter back into the closed position and secure with latches.
11. Replace the hopper in the rear of the machine.
12. Reconnect the battery cables to the machine. Raise the operator’s seat, disengage the
seat support rod and lower the seat to the closed position.
13. Start the machine and check the damper for proper operation.
IB 340480 (5-01) 3
1
2
4
4
4
3
4
FIG. 2 -- SOLENOID DAMPER KIT, 6100
IB 340480 (5-01)4
6200 INSTALLATION:
(Refer to FIG. 3 and 4)
1. Drive the machine onto a clean, flat work surface and set the machine parking brake.
FOR SAFETY: Before leaving or servicing machine, stop on level surface and set parking
brake. Then turn off machine and remove key.
2. . Start the machine. Press and hold the top of the hopper switch until the hopper is fully
raised. Release the switch into the hold position.
WARNING: Lift arm pinch point. Stay clear of hopper lift arms.
FOR SAFETY: When using machine, make sure adequate clearance is available before
raising hopper.
NOTE: Be aware that the minimum ceiling height needed to high dump the hopper is 2286mm
(90 in).
3. Push the hopper support bar in place onto the support cylinder.
WARNING: Raised hopper may fall. Engage hopper support bar.
4. Slowly lower the hopper by pressing down and holding the hopper switch until the hopper
support bar rests on the support bar stop.
WARNING: Lift arm pinch point. Stay clear of hopper lift arms.
5. Turn the machine power off.
6. Raise the operator seat and secure in place with the seat support rod.
7. Disconnect battery cables from machine.
WARNING: Always disconnect battery cables from machine before working
on electrical components.
8. Locate the solenoid bracket guard on the side of the fan plate.
9. Remove and set aside the solenoid bracket guard and mounting hardware.
10. Disconnect solenoid from main wiring harness.
11. Remove and discard the pin retainers, both retaining pins and the connecting link.
(Refer to FIG. 3)
12. Remove and discard the solenoid from the weldment on the side of the fan plate.
(Refer to FIG. 3)
13. File down the flat edge of the D shaped solenoid mounting hole, until the mounting hole is
round.
14. Mount the new solenoid (1) in the new round solenoid mounting hole. (Refer to FIG. 4)
15. Connect one end of the new link (2) to the new solenoid (1) with a new pin (3) and pin
retainers (4). Connect the other end of the link (2) to the damper rod with a new pin (3) and
pin retainers (4). (Refer to FIG. 4)
16. Replace the solenoid bracket guard with the set aside hardware. (Refer to FIG. 4)
IB 340480 (5-01) 5
Remove and discard old
solenoid from weldment.
Remove pin retainers and
both retaining pins from link.
FIG. 3 -- DAMPER SOLENOID REMOVAL, 6200
17. Reconnect the battery cables to the machine. Raise the operator’s seat, disengage the
seat support rod and lower the seat to the closed position.
18. Start the machine.
19. Press and hold the top of the hopper switch until the hopper is fully raised. Release the
switch in the hold position.
FOR SAFETY: When using machine, make sure adequate clearance is available before
raising hopper.
NOTE: Be aware that the minimum ceiling height needed to high dump the hopper is 2286mm
(90 in).
20. Move the hopper support bar off the cylinder into the storage position.
WARNING: Lift arm pinch point. Stay clear of hopper lift arms.
21. Press and hold the bottom of the hopper switch until the hopper is in the fully lowered
position.
WARNING: Lift arm pinch point. Stay clear of hopper lift arms.
22. Check the damper for proper operation.
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452
IB 340480 (5-01)6
Bracket guard
2
3
4
1
3
4
4
4
FIG. 4 -- SOLENOID DAMPER KIT, 6200
BILL OF MATERIALS FOR SOLENOID DAMPER KIT 384169
TENNANT
Ref. Part No. Description Qty.
1 384464 Solenoid, 12VDC, Damper 1
2 384440 Link, 0.12T 0.7W 1.6L 2/0.14H 1
3 384410 Pin, pivot 2
4 384411 Retainer, shaft, 0.125 Dia 4
Andere Handbücher für 6100
5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Tennant Bodenreinigungsmaschine Handbücher
Tennant
Tennant 810 Gas Bedienungsanleitung
Tennant
Tennant 750 Produkthandbuch
Tennant
Tennant MM267 Bedienungsanleitung
Tennant
Tennant 3240 Bedienungsanleitung
Tennant
Tennant 8010 Schulungshandbuch
Tennant
Tennant F14 Produkthandbuch
Tennant
Tennant F3 Produkthandbuch
Tennant
Tennant 1071121 Produkthandbuch
Tennant
Tennant ATLV 4300 Schulungshandbuch
Tennant
Tennant 355 Bedienungsanleitung
Tennant
Tennant 1240 Produkthandbuch
Tennant
Tennant 265 Bedienungsanleitung
Tennant
Tennant 1186E Bedienungsanleitung
Tennant
Tennant 6650 Bedienungsanleitung
Tennant
Tennant 810 LPG Bedienungsanleitung
Tennant
Tennant T5E Bedienungsanleitung
Tennant
Tennant M20 Schulungshandbuch
Tennant
Tennant 5700 Bedienungsanleitung
Tennant
Tennant 5200 Produkthandbuch
Tennant
Tennant T7 Bedienungs- und Montageanleitung
Beliebte Bodenreinigungsmaschine Handbücher anderer Marken
Nilfisk-Advance
Nilfisk-Advance Advance SC370 17B Bedienungsanleitung
Numatic
Numatic ET 4045 Bedienungsanleitung
HAWK ENTERPRISES
HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung
Mytee
Mytee 8070 Mytee-Lite Bedienungsanleitung
Kärcher
Kärcher B 140 R Bedienungsanleitung
Triple S
Triple S Ace 26T1 Bedienungsanleitung
