Tennant M17 Series Schulungshandbuch

IB 9015101 (07- 2016) 1

INSTRUCTION BULLETIN

No. 9015101

Machine: M17

Published: 07- 2016

Rev. 00

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 9015002

SYNOPSIS:

This kit contains the parts needed to replace the scrub circuit board on M17 sweeper- scrubbers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 1 hour)

PROTECT THE ENVIRONMENT

Please dispose of packaging materials, used machine components

such as batteries and fluids in an environmentally safe way according

to local waste disposal regulations.

Always remember to recycle.

PREPARATION:

1. Park the machine on a clean level surface,

turn off the machine, set the parking brake,

and remove the key.

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, set parking brake, and remove key.

2. Disconnect the battery cable from the

machine.

WARNING: Always disconnect battery

cable from machine before working on

electrical components.

3. Open the right shroud to access the electrical

box assembly.

INSTALLATION:

1. Remove both SEMS M6 hex screws securing

the electrical enclosure cover to the electrical

enclosure. Set the SEMS M6 hex screws

aside. (Fig. 1)

FIG. 1

NOTE:To avoid damaging electronic

components, the static ground strap (3) must be

worn at all times when handling / installing the

new scrub circuit board (1) onto the machine.

Attach the other end of the static ground strap to

the machine chassis.

IB 9015101 (07- 2016)2

2. Carefully remove the electrical enclosure

cover from the electrical enclosure and

position the electrical enclosure cover out of

the way. Do Not break or damage wires / wire

connections when removing the electrical

enclosure cover from the electrical enclosure.

(Fig.1/Fig.2)

FIG. 2

3. Disconnect all main wire harness connectors

from the existing scrub circuit board. Discard

all P2 / GND and P1 / B+ mounting hardware.

(Fig. 3)

4. Remove both M4 pan screws and nylon

washers securing the scrub circuit board to

the electrical enclosure. Set the M4 pan

screws and nylon washers aside. (Fig. 3)

5. Remove the scrub circuit board from the

plastic stand- offs in the electrical enclosure.

Discard the scrub circuit board. (Fig. 3)

6. Replace broken plastic stand- offs with new

plastic stand- offs (2). (Fig. 3)

7. Ensure the B+ and GND (ground) terminals

are tight on the new scrub circuit board (1).

(Fig. 3)

8. Place the scrub circuit board (1) onto the

plastic stand- offs (3) and use the two M4 pan

screws and nylon washers to secure the

scrub circuit board to the electrical enclosure.

(Fig. 3).

9. Reconnect all harness connections to the

scrub circuit board (1). (Fig. 3)

10. Use one M6 hex nut (8), one flat washer (6)

and one lock washer (7) to connect the P2 /

GND cable to the scrub circuit board (1). Hold

the circuit board stand- off with an open ended

wrench while tightening the M6 hex nut.

Torque the M6 hex nut to 36 in. lbs. (4.0 Nm).

Do Not over tighten hardware. (Fig. 3)

11. Use one M5 hex nut (5), one flat washer (6)

and one lock washer (4) to connect the P1 /

B+ cable to the scrub circuit board (1). Hold

the circuit board stand- off with an open ended

wrench while tightening the M6 hex nut.

Torque the M5 hex nut to 30 in. lbs. (3.4 Nm).

Do Not over tighten hardware. (Fig. 3)

12. Reinstall the electrical enclosure cover onto

the electrical enclosure. (Fig. 1)

13. Reconnect the battery cable to the machine.

14. Close the right shroud.

15. Start and test the machine. Operate all

machine functions to ensure all modes /

systems are functional. If there is a Pickup

Module CAN alert, confirm CB1 (circuit

breaker 1) is not tripped. Press the CB1

button to reset the circuit breaker if it is

tripped.

IB 9015101 (07- 2016) 3

Remove and set M4 pan

screws and nylon flat

washers aside (Qty. 2 each)

Replace existing

scrub circuit board

with new scrub

circuit board (1)

Electrical

enclosure

Replace broken plastic

stand- offs with new

plastic stand- offs (2)

Replace

with lock

washer (7)

Replace with lock

washer (4)

To P2 /

GND

To P1 /

B+

Scrub circuit board - Bottom view

Replace with M5

hex nut (5) -

Torque to 30 in. lbs.

(3.4 Nm)

Replace with M6

hex nut (8) -

Torque to 36 in. lbs.

(4.0 Nm)

Replace

with flat

washers(6)

Hold B+ and GND terminals with open ended

wrench while tightening hex screws securing main

harness connectors to scrub circuit board (1)

NOTE:To avoid damaging electronic

components, static ground strap (3) must be worn

at all times when handling / installing new scrub

circuit board (1) onto machine. Attach other end

of static ground strap to machine chassis.

FIG. 3

IB 9015101 (07- 2016)4

Bill Of Materials For Circuit Board Kit, Scrub, Afmkt [T17/M17] - 9015002

Ref.

Tennant

Part No. Description Qty.

11225443 Circuit Board Assy [Scrub, Mustang, M17] 1

2 1210399 Stand- Off, Circuit Board [0.25”] 4

3 27964 Strap, Ground, Static, Disposable 1

4 07514 Washer, Lock, Int, 10, SS 1

5 1202864 Nut, Hex, Std, M5 X 0.80, Brs 1

61061918 Washer, Flat, 0.25B 0.47D .06, Brs 4

7 07515 Washer, Lock, Int, 0.25, SS 1

81061910 Nut, Hex, Std, M6 X 1.00, Brs 1

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Andere Handbücher für M17 Series

Andere Tennant Bodenreinigungsmaschine Handbücher

Tennant

Tennant 6100 G/LP Bedienungsanleitung

Tennant

Tennant 2100 Produkthandbuch

Tennant

Tennant E5 Bedienungsanleitung

Tennant

Tennant 750 Produkthandbuch

Tennant

Tennant 443C Bedienungsanleitung

Tennant

Tennant 9045218 Schulungshandbuch

Tennant

Tennant T1 Bedienungsanleitung

Tennant

Tennant 6200 Bedienungsanleitung

Tennant

Tennant 6100 Schulungshandbuch

Tennant

Tennant 1186 Bedienungsanleitung

Tennant

Tennant 6400E Bedienungsanleitung

Tennant

Tennant 6080 Bedienungsanleitung

Tennant

Tennant 2550 Bedienungsanleitung

Tennant

Tennant 1530 Produkthandbuch

Tennant

Tennant 1120 Produkthandbuch

Tennant

Tennant 1240 Produkthandbuch

Tennant

Tennant 1465 Bedienungsanleitung

Tennant

Tennant Nobles QUICK CLEAN 1500 Produkthandbuch

Tennant

Tennant 355D Bedienungsanleitung

Tennant

Tennant 6200D Bedienungsanleitung

Tennant

Tennant S30 Schulungshandbuch

Tennant

Tennant M17 Series Schulungshandbuch

Tennant

Tennant 235E Bedienungsanleitung

Tennant

Tennant 1200 Produkthandbuch

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung

IPC

IPC CT51-71 BT Bedienungsanleitung