Terex Z-30/20N Bedienungsanleitung

Operator's Manual

Serial Number Range

30/20N from Z30NF

22000 ANSI/CSA

North America

South America

Asia

30/20N RJ from Z30ND

1400

with

Maintenance

Information

Original Instructions

Seventh Edition

First Printing

Part No. 1297932GT

Operator's Manual Seventh Edition • First Printing

®-30/20N • Z®-30/20N RJ Part No. 1297932GT

Front Matter

Contents

Introduction ........................................................... 1

Symbol and Hazard Pictorials Definitions............. 6

General Safety ...................................................... 8

Personal Safety................................................... 12

Work Area Safety................................................ 13

Legend ................................................................ 21

Controls............................................................... 22

Inspections.......................................................... 24

Operating Instructions......................................... 39

Transport and Lifting Instructions ....................... 47

Maintenance ....................................................... 51

Specifications...................................................... 53

Seventh Edition: First Printing, February 2020

Genie and "Z" are registered trademarks of Terex South Dakota,

Inc. in the U.S.A. and many other countries.

These machines comply with

ANSI A92.20

CSA B354.6

Seventh Edition • First Printing Operator's Manual

Introduction

Part No. 1297932GT Z®-30/20N • Z®-30/20N RJ 1

Introducti on

About this manual

Genie appreciates your choice of our machine for

your application. Our number one priority is user

safety, which is best achieved by our joint efforts.

This book is an operation and daily maintenance

manual for the user or operator of a Genie

machine.

This manual should be considered a permanent

part of your machine and should remain with the

machine at all times. If you have any questions,

contact Genie.

Product Identification

The machine serial number is located on the serial

label.

Serial number stamped

on chassis

Serial label

(located under cover)

Intended Use and Familiarization

Guide

The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site. Before operating the machine, it’s

the operator’s responsibility to read and

understand this familiarization guide.

Each person must be trained to operate a

Mobile Elevating Work Platform (MEWP).

Familiarization with the MEWP must be given

to each person who is authorized, competent

and trained.

Only trained and authorized personnel should

be permitted to operate the machine.

The operator is responsible to read,

understand, and obey the manufacturer’s

instructions and safety rules provided in the

Operator’s Manual.

The Operator’s Manual is located in the

manual storage container, at the platform.

For specific product applications, see

Contacting The Manufacturer.

Operator's Manual Seventh Edition • First Printing

Introduction

2 Z®-30/20N • Z®-30/20N RJ Part No. 1297932GT

Platform controls symbology and related

machine movement:

Platform level swtich

Platform rotate switch

Jib boom up/down

Primary boom up/down

Turntable rotate

Primary boom extend/retract

switch

Secondary boom up/down

Drive forward/reverse

Steer right/left

Ground controls symbology and related

machine movement:

Platform level, jib

boom up/down,

primary boom

extend/retract,

primary boom

up/down, and

secondary boom

retract/lower.

Turntable rotate and

platform rotate

Sequential functions and movement:

Drive and steer.

Interlocked functions:

Elevated drive speed.

Elevated drive in an off-level condition.

Drive enable when the boom is rotated past the

non-steer wheels.

All platform and ground controls.

Limitations of use:

The intended use of this machine is to lift

personnel, including tools, and materials to an

aerial work site.

Do not elevate the platform unless the machine

is on firm level ground.

Stability enhancing means:

Foam filled tires.

Restricted operating envelope:

500 lbs/227 kg platform capacity.

Seventh Edition • First Printing Operator's Manual

Introduction

Part No. 1297932GT Z®-30/20N • Z®-30/20N RJ 3

Bulletin Distribution and

Compliance

Safety of product users is of paramount

importance to Genie. Various bulletins are used by

Genie to communicate important safety and

product information to dealers and machine

owners.

The information contained in the bulletins is tied to

specific machines using the machine model and

serial number.

Distribution of bulletins is based on the most

current owner on record along with their

associated dealer, so it is important to register your

machine and keep your contact information up to

date.

To ensure safety of personnel and the reliable

continued operation of your machine, be sure to

comply with the action indicated in a respective

bulletin.

Contacting the Manufacturer

At times it may be necessary to contact Genie.

When you do, be ready to supply the model

number and serial number of your machine, along

with your name and contact information. At

minimum, Genie should be contacted for:

Accident reporting

Questions regarding product applications and

safety

Standards and regulatory compliance information

Current owner updates, such as changes in

machine ownership or changes in your contact

information. See Transfer of Ownership, below.

Transfer of Machine Ownership

Taking a few minutes to update owner information

will ensure that you receive important safety,

maintenance and operating information that

applies to your machine.

Please register your machine by visiting us on the

web at www.genielift.com or by calling us toll free

at 1-800-536-1800.

Operator's Manual Seventh Edition • First Printing

Introduction

4 Z®-30/20N • Z®-30/20N RJ Part No. 1297932GT

Danger

Failure to obey the instructions and

safety rules in this manual will result

in death or serious injury.

Do Not Operate Unless:

You learn and practice the principles of safe

machine operation contained in this operator’s

manual.

1 Avoid hazardous situations.

Know and understand the safety rules

before going on to the next section.

2 Always perform a pre-operation inspection.

3 Always perform function tests prior to use.

4 Inspect the workplace.

5 Only use the machine as it was intended.

You read, understand and obey the

manufacturer’s instructions and safety

rules—safety and operator’s manuals and

machine decals.

You read, understand and obey employer’s

safety rules and worksite regulations.

You read, understand and obey all applicable

governmental regulations.

You are properly trained to safely operate the

machine.

Safety Sign Maintenance

Replace any missing or damaged safety signs.

Keep operator safety in mind at all times. Use mild

soap and water to clean safety signs. Do not use

solvent-based cleaners because they may damage

the safety sign material.

Seventh Edition • First Printing Operator's Manual

Introduction

Part No. 1297932GT Z®-30/20N • Z®-30/20N RJ 5

Hazard Classification

Decals on this machine use symbols, color coding,

and signal words to identify the following:

Safety alert symbol—used to alert

you to potential personal injury

hazards. Obey all safety

messages that follow this symbol

to avoid possible injury or death.

Indicates a hazardous situation

which, if not avoided, will result in

death or serious injury.

Indicates a hazardous situation

which, if not avoided, could result

in death or serious injury.

Indicates a hazardous situation

which, if not avoided, could result

in minor or moderate injury.

Indicates a property damage

message.

DANGER

WARNING

CAUTION

NOTICE

Operator's Manual Seventh Edition • First Printing

Symbol and Hazard Pictorials Definitions

6 Z®-30/20N • Z®-30/20N RJ Part No. 1297932GT

Symbol and Hazard Pic torials Definiti ons

Fire hazard Explosion hazard Explosion hazard Do not use ether or

other high energy

starting aids on

machines equipped

with glow plugs.

No smoking.

No flame.

Stop engine.

Crush hazard No smoking Explosion hazard Electrocution hazard Maintain required

clearance

Tip-over hazard Tip-over hazard Grounded AC

3-wire only

Replace damaged

wires and cords

Replace tires with

tires of same

specification.

Wheel load Wind speed Maximum capacity Side force Batteries used as

counterweights

Tie-down point Lifting point Platform tie-down

instructions

Lifting & tie down

instructions

Lanyard anchorage

points

Seventh Edition • First Printing Operator's Manual

Symbol and Hazard Pictorials Definitions

Part No. 1297932GT Z®-30/20N • Z®-30/20N RJ 7

Corrosive acid. Color coded direction

arrows

Runaway hazard Collision hazard Collision hazard

Electrocution hazard Avoid contact Disconnect battery Voltage rating for

power to platform

Pressure rating for air

line to platform

Recovery procedure if tilt alarm sounds while

elevated.

Platform uphill:

1Lower primary.

2Lower secondary.

3Retract primary.

Platform downhill:

1Retract primary.

2Lower secondary.

3Lower primary.

Read the operator’s

manual

Read the service

manual

Access by trained and

authorized personnel

only

Operator's Manual Seventh Edition • First Printing

General Safety

8 Z®-30/20N • Z®-30/20N RJ Part No. 1297932GT

General Safety

1280819

Annual Inspection Record

Failure to complete required inspections

could result in death or serious injury.

Model Serial number

Date of

Inspection

Inspected

Machine

Owner

52865 B

WARNING

Scheduled maintenance

inspections must be

completed as specified in

the appropriate service

manual.

Use this decal to record

the date of the annual

inspection, the initials of

the inspector and the

machine owner.

Use the maintenance

inspection report in the

service manual for required

recordkeeping. Keep

records on all inspections

for four years.

Maintenance inspections

must be completed by a

person trained and qualified

on the maintenance of this

machine.

114390

1267121

31060

52865

31060

114390

1263543

Andere Handbücher für Z-30/20N

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Terex Hubarbeitsbühne Handbücher

Terex

Terex Genie GR-20J Bedienungsanleitung

Terex

Terex Genie Z-34/22 Bedienungsanleitung

Terex

Terex Genie Z-62 Installations- und Betriebsanleitung

Terex

Terex Genie Z4525XCM-2501 Bedienungsanleitung

Terex

Terex Genie Z-34/22 IC Installations- und Betriebsanleitung

Terex

Terex Genie Lift Guard S-40 Installations- und Betriebsanleitung

Terex

Terex Genie S-60XC Bedienungsanleitung

Terex

Terex Genie Z-34 Bedienungsanleitung

Terex

Terex S85XCH-3740 Bedienungsanleitung

Terex

Terex S65XCM-101 Installations- und Betriebsanleitung

Terex

Terex L13I Bedienungsanleitung

Terex

Terex Z-33 Bedienungsanleitung

Terex

Terex Genie Z-45/25 Bi-Energy Bedienungsanleitung

Terex

Terex S8015-12264 Installations- und Betriebsanleitung

Terex

Terex TM Series Bedienungsanleitung

Terex

Terex Genie S-40/45 Bedienungsanleitung

Terex

Terex Genie Z-80/60 Bedienungsanleitung

Terex

Terex Genie Z-51/30J Bedienungsanleitung

Terex

Terex SLA04-25259 Bedienungsanleitung

Terex

Terex Genie TZ-50 Bedienungsanleitung

Terex

Terex Genie GTH-3007 Bedienungsanleitung

Terex

Terex Genie GS-4655 Bedienungsanleitung

Terex

Terex Genie Z-45/25 Bi-Energy Bedienungsanleitung

Terex

Terex Genie Z-34/22 Installations- und Betriebsanleitung

Beliebte Hubarbeitsbühne Handbücher anderer Marken

Genie

Genie Z-80 Bedienungsanleitung

Genie

Genie Z-45/25 Bedienungsanleitung

JLG

JLG Skytrak 6036 Gebrauchs- und Pflegehandbuch

LGMG

LGMG T65JE Bedienungsanleitung

Genie

Genie Z-135/70 Bedienungsanleitung

Oshkosh Corporation

Oshkosh Corporation JLG H800AJ Gebrauchs- und Pflegehandbuch

Oshkosh

Oshkosh JLG 1500SJ Installations- und Benutzerhandbuch

Skyjack

Skyjack SJ30AJE Bedienungsanleitung

Oshkosh

Oshkosh JLG 800A Installations- und Benutzerhandbuch

Skyjack

Skyjack SJ 46AJ Bedienungsanleitung

Molift

Molift Quick Raiser 205 Bedienungsanleitung

Snorkel

Snorkel SL26RTE Kurzanleitung

Oshkosh Corporation

Oshkosh Corporation JLG E300A Bedienungsanleitung

Skyjack

Skyjack SJ45 T+ Bedienungsanleitung

Genie

Genie S-105 Bedienungsanleitung

nifty

nifty 170SD series Montageanleitung

JLG

JLG 15MVL Series Bedienungsanleitung

Genie

Genie Z-45 XC Bedienungsanleitung