TESTO 606-1 Bedienungsanleitung
Instruction manual
testo 606-1
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
11
Short manual testo 606-1
Protection cap: Park position
Sensing electrodes
Display
Control keys
Battery compartment (on rear)
Test resistance contact
List of settable materials, for
sticking into the protective cap
Basic settings
Instrument off > press and hold 2s > select with ( ),
confirm with ( ):
Auto off-Funktion: OFF,ON
Switching the instrument on
Press .
Switching the display light on(for 10s)
Instrument on > press
Select display mode
Instrument on > select with :
Current reading > Hold: Readings are held
Switching the instrument off:
Instrument on >press and hold 2s.
de
enfresitptsvnl????
Short manual testo 606-1
12
Safety and the environment
About this document
iPlease read this documentation through carefully and
familiarise yourself with the product before putting it to use.
Keep this document to hand so that you can refer to it when
necessary. Hand this documentation on to any subsequent
users of the product.
iPay particular attention to information emphasised by the
following symbols:
With the signal word Caution!:
Warns against hazards which could result in minor physical injury
or damage to equipment if the precautionary measures indicated
are not taken.
Important.
Avoid personal injury/damage to equipment
iOnly operate the measuring instrument properly, for its
intended purpose and within the parameters specified in the
technical data. Do not use force.
iNever store the product together with solvents, acids or other
aggressive substances.
iOnly carry out the maintenance and repair work that is
described in the documentation. Follow the prescribed steps
when doing so. Use only OEM spare parts from Testo.
Protecting the environment
iTake faulty rechargeable batteries as well as spent batteries to
the collection points provided for them.
iSend the product back to Testo at the end of its useful life. We
will ensure that it is disposed of in an environmentally friendly
manner.
Safety and the enviroment
13
Specifications
Functions and use
The testo 606-1 is a material moisture measuring instrument. It is
normally used to determine the material moisture content in wood
or building materials. The measurement procedure used is
suitable for overview measurement to determine whenther the
material is continuing to dry out. The material moisture is given in
% by weight.
Measurement data
· Sensors:
Electrical resistance (conductivity
measurement), Testo humidity sensor,
NTC temperature sensor
· Parameters:
% by weight material moisture (wood,
building materials), %rH, td, wb, °C, °F
· Measuring ranges:
See chapter Using the Product
· Resolutions:
0.1 %, 0.1 °C, 0.1 °F, 0.1 %rH
· Accuracies (Nominal temperature
25 °C, ±1 Digit):
Conductivity measurement ±1 %,
±0.5 °C, ±0.9 °F,
±2.5%rH (5...95%rH)
· Measuring rate:
0.5 s, humidity: 1s
Further instrument data
· Protection class: IP20
· Ambient conditions:
-10...50 °C, 14...122 °F
· Storage/transport conditions:
-40...70 °C, -40...158 °F
· Voltage supply:
2x 1.5 V type AAA
· Battery life:
130 h (without display light)
· Dimensions:
119x46x25mm / 4.69x1.81x0.98” (inc.
protection cap)
· Weight: 90 g / 3.2 oz (inc. batteries and
protection cap)
Directives, standards and tests
· EC Directive: 2004/108/EEC
Warranty
· Duration: 2 years
· Warranty conditions: see guarantee
card
de
enfresitptsvnl????
Specification
14
Product description
At a glance
Protection cap: Park position
Sensing electrodes
Caution! Risk of injury
from sensing electrodes!
iAttach protection cap
when not in use.
Display
Control keys
Battery compartment (on rear)
Test resistance contact
List of settable materials, for
sticking into the protective cap
First steps
²Inserting batteries:
1To open the battery compartment, push the battery cover
down.
2Insert batteries (2x 1.5 V type AAA). Observe the polarity!
3To close the battery compartment, push the battery cover
back on.
²Basic settings (configuration mode):
Adjustable functions
· Auto off function: OFF,ON (instrument switches off automatically if no key is
pressed for 10 minutes)
1When switching the instrument on, press and hold until
and appear on the display (configuration mode).
- The adjustable function is displayed. The current setting
flashes.
2Press ( ) several times until the desired setting flashes.
Product description
15
3Press ( ) to confirm the input.
- The instrument changes to measuring mode.
Using the product
To ensure correct readings, repeat the measurement at several
points. Always measure wood moisture across the grain.
The values displayed are highly dependent on the building
material/manufacturer used, and on the ambient conditions .
As the materials are natural, the same materials can vary from
batch to batch.
²Switching the instrument on:
iPress .
- Measuring mode is opened.
²Switching the display light on:
The instrument is switched on.
iPress .
- The display light goes out automatically if no key is
pressed for 10 seconds.
²Setting the material characteristic curve:
The material moisture is indicated in the top line of the
display. The material symbol (wood) or (building
material) is displayed with the relevant material number (see
enclosed sticker for the inside of the protective cap).
Settable materials Measuring range
1. beech, spruce, larch, birch, cherry, walnut 8.8...54.8 % by weight
2. oak, pine, maple, ash-tree, douglas fir, meranti 7.0...47.9 % by weight
3. cement screed, concrete 0.9...22.1 % by weight
4. anhydrite screed 0.0...11.0 % by weight
5. cement mortar 0.7...8.6 % by weight
6. lime mortar, plaster 0.6...9.9 % by weight
7. bricks 0.1...16.5 % by weight
iPress several times until the desired material
characteristic curve appears.
²Testing the instrument function:
1Press several times until Test: lights up.
de
enfresitptsvnl????
Using the product
16
2Connect sensing electrodes with the contacts of the test
resistor on the top of the protection cap.
-Test flashes.
-Test: ok lights up: instrument is functioning.
Test: ok does not light up: test not possible, see chapter
'Tips and assistance'.
3Press back to measurement menu.
²Changing the display view:
Adjustable views
· Current reading
·Hold: Readings are held.
iPress until the desired view appears.
²Switching the instrument off:
iPress and hold until the display goes out.
Maintaining the product
±Changing batteries:
1To open the battery compartment, push the battery cover
down.
2Remove used batteries and insert new batteries
(2x 1.5 V type AAA). Observe the polarity!
3To close the battery compartment, push the battery cover
back on.
±Cleaning the housing:
iClean the housing with a moist cloth (soap suds) if it is dirty.
Do not use aggressive cleaning agents or solvents!
Using the product
17
Tips and assistance
Questions and answers
Question Possible causes/solutions
Hi or Lo · Readings outside the measuring range (too high, too
low): Keep to the permitted measuring range.
· Residual capacity <10 min: Change batteries.
Testing the instrument
function: Test: ok does
not light up · Clean sensing electrodes and contacts on the top
of the protection cap.
· If the error message appears again, send the
instrument to Testo Customer Service.
Meas. electrodes defective/
worn · Send instrument to Testo customer service.
Typical values for equilibrium moisture (Air dryness in building
materials1):
Material Char. curve Material moisture
Anhydrite screed 4 <0.5 % by weight
Concrete 3 <2.2 % by weight
Plaster 3 <0.8 % by weight
Lime mortar 6 <2.0 % by weight
Brick, fireded
without hole 7 <1.0 % by weight
Cement screed 3 <3.0 % by weight
Cement mortar 5 <3.0 % by weight
1In ambient conditions of 20 °C and 65 % RH
Guideline values for the installation moisture of wood, which sets
in as an average after a certain period in use-status (DIN 1052-1
(4/88) Para. 4.2.1.):
Char. curve Application area Wood humidity in % by weight
1 or 2 buildings closed on all sides with heating 9 ± 3
1 or 2 buildings closed on all sides without heating 12 ± 3
1 or 2 roofed open buildings 15 ± 3
1 or 2 constructions which are open to the weather on all sides 18 ± 6
If we could not answer your question, please contact your dealer
or Testo Customer Service.
de
enfresitptsvnl????
Tips and assistance
18
Test Equipment Depot - 800.517.8431
99 Washington Street,Melrose, MA 02176
TestEquipmentDepot.com
0973.6063/03/Sh/dr/30.04.2008
Test Equipment Depot - 800.517.8431
99 Washington Street,Melrose, MA 02176
TestEquipmentDepot.com
Andere Handbücher für 606-1
5
Inhaltsverzeichnis
Andere TESTO Messgerät Handbücher
TESTO
TESTO 0564 2552 01 Bedienungsanleitung
TESTO
TESTO 570 Bedienungsanleitung
TESTO
TESTO 770 Bedienungsanleitung
TESTO
TESTO 606-2 Bedienungsanleitung
TESTO
TESTO 435 Bedienungsanleitung
TESTO
TESTO 174T Bedienungsanleitung
TESTO
TESTO 6448 Bedienungsanleitung
TESTO
TESTO 110 Bedienungsanleitung
TESTO
TESTO 300 LL Bedienungsanleitung
TESTO
TESTO 177-T1 Bedienungsanleitung
TESTO
TESTO 400 Handbuch
TESTO
TESTO 400 Bedienungsanleitung
TESTO
TESTO Smart Probes 115i Bedienungsanleitung
TESTO
TESTO 300 Handbuch
TESTO
TESTO 330 Bedienungsanleitung
TESTO
TESTO 420 Bedienungsanleitung
TESTO
TESTO Smart Probes 805i Installationshandbuch
TESTO
TESTO 512 Bedienungsanleitung
TESTO
TESTO 316-3 Bedienungsanleitung
TESTO
TESTO 535 Bedienungsanleitung
